特超稠油污水回掺降粘集输工艺

通过对河南古城油田BQ10区特超稠油乳状液的室内试验分析,指出该种乳状液的实际相突变点为68%左右,当相浓度Φ≥68%时,以W/O型为主的乳状液突变为以O/W型为主的乳状液.乳状液变型后,原油与管道内壁之间的摩擦以及原油之间的摩擦转变为水与管道内壁及水与水之间的摩擦,从而大幅度降低其粘度和摩阻损失;通过对古城BQ10区特超稠油区块单元内部污水回掺降粘集输的现场试验,证明与室内试验分析得出的结论相符合,说明区块单元污水回掺不同于常规的掺热水,也不同于掺联合站处理过的净化污水,它优于单井掺稀油.最后指出该工艺可有效地降低井站回压,方便生产管理,降低开采成本,提高采油效率和经济效益,具有低耗节能的优点.     

黄河下游平滩流量对来水来沙变化的响应

本文探讨了平滩流量对来水来沙的滞后响应规律，发现平滩流量不仅与当年的水沙条件有关，而且与前期水沙条件有关，是一定时期内的水沙条件累积作用的结果。当采用滑动平均值来反应前期水沙条件的累积影响时，得出平滩流量与滑动平均汛期流量和滑动平均来沙系数的相关程度分别在4年和5年时达到最大值。据此建立了能够反映来水流量和来沙系数前期综合影响的平滩流量计算方法，可以用来估算黄河下游主要测站平滩流量随水沙条件的变化。     

硅化腐植酸钠GFN-1的研制

针对目前生产腐植酸硅化产品原料受限的缺点,在大量试验的基础上,确定了一条以腐植酸和硅化剂为主要原料的生产工艺,合成了一种与有机硅腐植酸钾(OSAM-K)性能相当的硅化腐植酸钠产品GFN-1,对其常规性能指标和在清水及无固相聚合物钻井液体系中、在膨润土浆和低固相钻井液体系中应用指标,耐温性能进行了对比实验。实验结果表明,GFN-1作为钻井液添加剂,具有良好的降滤失、降黏、耐温及热稳定性,并兼有优良的控制页岩分散能力,其大多数应用性能相当于或略优于OSAM-K,作为替代品完全能够满足油田现场应用的需要。GFN-1的硅化原料性质稳定、来源广泛,生产工艺简单易行,产品质量稳定,具有较好的推广价值。     

重油纳米化助燃效果研究与表征

将复配的分散剂加入重油中制备得到重油纳米颗粒，采用氧弹热值对比法对所研制的纳米化重油进行实验室评价。研究结果表明，纳米化后的重油燃烧性能得到了改善，在掺水量为3％～12％时，重油的燃烧效率提高了2．5％～6．1％。通过TEM观察，纳米化后的重油呈水包油（O／W）型乳液结构，油水界面清晰，界面膜较厚，乳化油粒径约为20～50nm，油水分散均匀，并且分散后的重油粘度增幅小，掺水量在15％以内，粘度增幅不超过20％，并且随着掺水量的增加，乳化重油的粘度逐渐减少。另外，乳化重油稳定性好，室温下至少可保存6个月，在80℃下存放3天未发生破乳现象。     

注射成型中塑料熔体充填流动的粘度模型研究

对比研究了Cross_Exp 和Cross_WLF两种粘度模型 ,并分别利用这两种模型通过实例模拟研究了熔体粘度的压力依赖性对注射压力模拟的影响     

溶聚丁苯橡胶聚合溶液粘度的研究

研究了（乙二醇二甲醚、二乙二醇二甲醚）－正丁基锂－抽余油体系地溶聚乙苯橡胶不同聚合时间聚合溶液粘度的变化，发现聚合溶粘度与活性种的活性有关，高温严重破坏活性种的活性，计节剂量是杀死活性种活性的另一因素。同时考察了不同苯乙烯／丁二烯（S／B）体系，正丁基锂引发剂用量对聚合粘影响规律，发现S／B越大，聚合粘度越小，S／B越小，聚合粘度越大，引发剂用量减少，聚合液粘度增大。     

Linear viscoelastic properties of mixtures of 3- and 4-arm polybutadiene stars

The viscoelastic properties of a three-arm and a four-arm star polybutadiene with the same arm molecular weight (M_a) were studied. The zero-shear recoverable compliance (J⁰_e) and plateau modulus (G⁰_N) for these stars are the same. The zero-shear viscosity (η₀) of the three-arm star is 20% lower than that of the four-arm star. Mixtures of the stars had J⁰_e and G⁰_N unchanged. A $\text{50}\text{50}$ mixture of the three- and four-arm star was diluted with a low molecular weight linear polybutadiene. G⁰_N∝ø²; J⁰_e∝ø^?1 and M_e∝ø^?1, as expected for dilution with a θ-solvent.     

依靠弯道控导河势流路

在天然河道中，河势演变虽具有一定的随机性，但仍有一定的规律可循，在一个河段内，一般可归纳出2－3条基本流路，为控制河势变化，需要选择出一条基本流路进行河道整治，当连续发生枯水期或洪水期时，部分河段的河势可能出现大的变化，为防止不利河势向下游传播，可修建较长的龙头弯道工程，利用龙头弯道工程分段调整，控导河势，保持河势稳定。     

Oscillating Cup Viscosity Measurements of Aluminum Alloys: A201, A319 and A356

An oscillating cup viscometer was developed to measure the absolute viscosities of molten metals. Previous experiments established the capability of the apparatus to characterize the viscosities of molten nickel-based superalloys. However, modifications to the instrument and its theoretical analysis were required for reliable measurements on molten aluminum alloys, presumably due to their lower densities and lower viscosities. The theoretical literature for the fluid flow inside an oscillating cup is reviewed, and a working equation without any correction factor is developed for the improved viscometer. Some design parameters of the viscometer that directly affect the accuracy of viscosity estimation by using the working equation are discussed. A special vertical furnace was adopted to uniformly heat a longer cylindrical sample (10 mm inner diameter and 120 mm length) with a temperature difference of less than 2°C over the sample length. The measuring procedure was also improved to get more accurate motion parameters. It is estimated that the working equation and improved instrument provide an uncertainty of less than 4%. In addition, applications and experimental data are presented for pure aluminum and three aluminum alloys: A201, A319, and A356.     

降低彩板生产稀释剂消耗的方法探讨

结合彩涂板生产实际，介绍了几种降低稀释剂消耗的方法。