超细粉在内循环流化床中的流态化特性

在内径120 mm的半圆柱形内循环流化床中,以平均粒径387 nm的Ti O2为原料,考察了单独通入流化气、射流气和同时通入流化气和射流气三种流化方式下超细粉的流化特性以及射流气速对超细粉聚团尺寸的影响。结果表明:同时通入流化气和射流气时,流化气能促进粉体循环,消除环隙死区;高速射流能有效破碎聚团,显著减小聚团尺寸,从而使超细粉在环隙区与导流管之间形成稳定循环,小聚团在环隙区实现平稳流态化。随着射流气速的增大,聚团尺寸减小,粒度分布变窄,在射流气速分别为60,90,120,150 m/s的条件下,聚团平均直径分别为194,158,147,135μm。     

Separation of hematite from banded hematite jasper (BHJ) by magnetic coating

The separation of iron oxide from banded hematite jasper(BHJ) assaying 47.8% Fe, 25.6% Si O2 and 2.30%Al2O3 using selective magnetic coating was studied. Characterization studies of the low grade ore indicate that besides hematite and goethite,jasper, a microcrystalline form of quartzite, is the major impurity associated with this ore. Beneficiation by conventional magnetic separation technique could yield a magnetic concentrate containing 60.8% Fe with 51% Fe recovery. In order to enhance the recovery of the iron oxide minerals, fine magnetite, colloidal magnetite and oleate colloidal magnetite were used as the coating material. When subjected to magnetic separation, the coated ore produces an iron concentrate containing 60.2% Fe with an enhanced recovery of56%. The AFM studies indicate that the coagulation of hematite particles with the oleate colloidal magnetite facilitates the higher recovery of iron particles from the low grade BHJ iron ore under appropriate conditions.     

Magnetic Nanoparticle Arrays Self-Assembled on Perpendicular Magnetic Recording Media

We study magnetic-field directed self-assembly of magnetic nanoparticles onto templates recorded on perpendicular magnetic recording media, and quantify feature width and height as a function of assembly time. Feature widths are determined from Scanning Electron Microscope (SEM) images, while heights are obtained with Atomic Force Microscopy (AFM). For short assembly times, widths were ~150 nm, while heights were ~14 nm, a single nanoparticle on average with a 10:1 aspect ratio. For long assembly times, widths approach 550 nm, while the average height grows to 3 nanoparticles, ~35 nm; a 16:1 aspect ratio. We perform magnetometry on these self-assembled structures and observe the slope of the magnetic moment vs. field curve increases with time. This increase suggests magnetic nanoparticle interactions evolve from nanoparticle–nanoparticle interactions to cluster–cluster interactions as opposed to feature–feature interactions. We suggest the aspect ratio increase occurs because the magnetic field gradients are strongest near the transitions between recorded regions in perpendicular media. If these gradients can be optimized for assembly, strong potential exists for using perpendicular recording templates to assemble complex heterogeneous materials.     

Se doped nickel-molybdenum bimetal sulfide with enhanced electrochemical activity for hydrogen evolution reaction

In this work, we synthesized Se doped MoS₂@Ni₃S₂ with nanosheets coated nanorods structure supported on Ni foam (MoNiSeS). Firstly, MoS₂@Ni₃S₂ (MoNiS) nanorods was synthesized by hydrothermal method. After selenization treatment, MoSe₂ successfully formed on the edge of MoS₂ nanosheets and particle Ni₃S₂ transformed into NiSe, in which MoSe₂ and NiSe acted as new phase in MoNiSeS. The obtained MoNiSeS only needs a low overpotential of 68 mV to reach the current density of 10 mA cm^?2, and has a low Tafel plots of 72.77 mV dec^?1 and good electrochemical durability, whose electrochemical activity is much better than that of MoNiS and NiSeS, implying the introduction of Mo and Se is beneficial to improve the electrocatalytic performance of NiS for HER. In addition, the proper amount of Mo source, which has an effect on the morphology of product, has also been investigated. For MoNiSeS, the typical nanosheets coated nanarods expose more active sites and the synergic effects is good to the improvement of the catalytic activity. Meanwhile, WNiSeS has also been prepared using the same method and the corresponding results show that the electrochemical activity of WNiSeS is much better than that of NiSeS, proving the universality of this strategy.     

Ga-doped IZO films obtained by magnetron sputtering as transparent conductors for visible and solar applications

C-axis textured thin films of gallium-doped indium zinc oxide (GIZO) with a 2% ratio of Ga/Zn, were obtained via RF-magnetron sputtering with high transparency and electrical conductivity. A Box-Behnken response surface design was used to evaluate the effects of the deposition parameters (In₂O₃ target power, deposition time, and substrate temperature) on the chemical composition, optical, electrical, and structural properties of the GIZO films. The optical constants and the electrical properties were obtained using optical models. The GIZO stoichiometry, and therefore the In/Zn atomic ratio, affected the crystallinity, crystalline parameters, band gap, and charge carrier mobility of the GIZO films. The charge carrier density was related to the change in the crystalline parameters of the hexagonal structure and the In/Zn atomic ratio. The best electrical conductivity values (1.75?×?10³ Ω^?1 cm^?1) were obtained for GIZO films with In/Zn ratio ≥?1. Several figures of merit (FOM) defined for the visible and solar regions were comparatively used to select the optimal In/Zn atomic ratio that provided the best balance between the conductivity and the transparency. The optimal In/Zn ratio was in a range of 0.85–0.90 for the GIZO films.     

Digital image correlation strain measurement of thick adherend shear test specimen joined with an epoxy film adhesive

Structural bonding and bonded repairs of composite materials become more and more important. Understanding the strain within the bondline leads to suitable bonding design. For new design approaches the strain distribution within the bondline has to be analyzed. Thus, often finite element analysis (FE) are used. However, a huge challenge is the availability of reliable material properties for the adhesives and their validation. Previous work has shown that it is possible to measure the small displacements resulting within thin epoxy film adhesives using high resolution digital image correlation (DIC). In this work a 2D DIC setup with a high resolution consumer camera is used to visualize the strain distribution within the bondline over the length of the joint as well as over the adhesive thickness. Therefore, single lap joints with thick aluminum adherends according to ASTM D 5656 are manufactured and tested. Local 2D DIC strain measurements are performed and analyzed. Two different camera setups are used and compared. The evaluation provides reliable material data and enables a look insight the bondline. The results of the full field strain data measured with DIC are compared with numerical simulations. Thus, material models as well as chosen parameters for the adhesive are validated. Compared to extensometers, giving only point-wise information for fixed measuring points, the DIC allows a virtual point-wise inspection along the complete bondline. Furthermore, it allows measuring close to the bondline to reduce the influence of adherend deformation.     

Dihydrotanshinone,a Natural Diterpenoid,Preserves Blood-Retinal Barrier Integrity via P2X7 Receptor

Activation of P2X7 signaling, due to high glucose levels, leads to blood retinal barrier (BRB) breakdown, which is a hallmark of diabetic retinopathy (DR). Furthermore, several studies report that high glucose (HG) conditions and the related activation of the P2X7 receptor (P2X7R) lead to the over-expression of pro-inflammatory markers. In order to identify novel P2X7R antagonists, we carried out virtual screening on a focused compound dataset, including indole derivatives and natural compounds such as caffeic acid phenethyl ester derivatives, flavonoids, and diterpenoids. Molecular Mechanics/Generalized Born Surface Area (MM/GBSA) rescoring and structural fingerprint clustering of docking poses from virtual screening highlighted that the diterpenoid dihydrotanshinone (DHTS) clustered with the well-known P2X7R antagonist JNJ47965567. A human-based in vitro BRB model made of retinal pericytes, astrocytes, and endothelial cells was used to assess the potential protective effect of DHTS against HG and 2′(3′)-O-(4-Benzoylbenzoyl)adenosine-5′-triphosphate (BzATP), a P2X7R agonist, insult. We found that HG/BzATP exposure generated BRB breakdown by enhancing barrier permeability (trans-endothelial electrical resistance (TEER)) and reducing the levels of ZO-1 and VE-cadherin junction proteins as well as of the Cx-43 mRNA expression levels. Furthermore, HG levels and P2X7R agonist treatment led to increased expression of pro-inflammatory mediators (TLR-4, IL-1β, IL-6, TNF-α, and IL-8) and other molecular markers (P2X7R, VEGF-A, and ICAM-1), along with enhanced production of reactive oxygen species. Treatment with DHTS preserved the BRB integrity from HG/BzATP damage. The protective effects of DHTS were also compared to the validated P2X7R antagonist, JNJ47965567. In conclusion, we provided new findings pointing out the therapeutic potential of DHTS, which is an inhibitor of P2X7R, in terms of preventing and/or counteracting the BRB dysfunctions elicited by HG conditions.     

Experimental study to assess the effect of carbon nanotube addition on the through-thickness electrical conductivity of CFRP laminates for aircraft applications

The present paper tests experimentally the through-thickness electrical conductivity of carbon fiber-reinforced polymer (CFRP) composites laminates for aircraft applications. Two types of samples were prepared: Type A samples with carbon nanotubes (CNTs) and Type B samples without CNTs. During the electrical experiments, electrical currents of several mA were injected through the specimens. Electrical resistance was monitored simultaneously in order to deduce the changes in the through-the-thickness electrical conductivity caused by the addition of CNTs. Improvement of electrical conduction by two orders of magnitude was achieved through the addition of 1 wt% carbon nanotubes as compared to classic CFRP without CNTs. For moisture saturated samples, the influence of moisture absorption on such measures was found to be negligible.     

Thermoplastic and low dielectric constants polyimides based on BPADA-BAPP

ABSTRACT

The thermoplastic and low dielectric constants polyimides were introduced. The polyimides were prepared by pyromellitic dianhydride (PMDA) or 4,4?-(4,4?-Isopropylidenediphenoxy)diphthalic anhydride (BPADA) as anhydride monomer and 4,4?-oxydianiline (ODA) or 2,2-bis(4-(4-aminephenoxy)phenyl)propane (BAPP) as amine monomer. The polyimides were well characterized by FT-IR, thermogravimetric analysis, dynamic thermomechanical analysis, dielectric measurement, and tensile test. The dielectric constants were 2.32–2.95 compared with 3.10 of ODA-PMDA polyimide, while partly polyimides were thermoplastic. The results indicated anhydride monomers, containing lateral methyl groups, made polyimides become thermoplastic. The results of molecular simulations via Materials Studio also proved this conclusion.     

Importance of finding the proper ratio of alkaline earth oxide in a lithium-bismuthate-phosphate glass in order to enhance the tailoring of structural and electrical properties

Structural features of the glass family xLi₂O- yMgO (4.8 Bi₂O₃ 47.6 P₂O₅) obtained by melt quenching technique were studied taking into account the density, FTIR and UV–vis spectra and also the electrical response observed by impedance spectroscopy. In this work it becomes clarified how the alkaline earth oxides stabilize the glassy matrix and also, the fundamental importance of determining the optimal proportion in order to obtain a flabby easily polarizable matrix to enhance the electrical behavior due to a boosted cation mobility. It is evidenced that when the glass composition becomes complex it is needed to take into account a larger number of structural parameters to understand, to predict or to design the resulting physical properties.