A novel quasi-oppositional harmony search algorithm and fuzzy logic controller for frequency stabilization of an isolated hybrid power system

The intermittent wind power in isolated hybrid distributed generation (IHDG) may cause serious problems associated with frequency (f) and power (P) fluctuation. Energy storage devices such as battery, super capacitor, and superconducting magnetic energy storage (SMES) may be used to reduce these fluctuations associated with f and P. This paper presents a study of IHDG power system for improving both f and P deviation profiles with the help of SMES. The studied IHDG power system is consisted of wind turbine generator and diesel engine generator. Both f and P control problems of the studied power system model are addressed in presence or absence of SMES. Fuzzy logic based proportional–integral–derivative (PID) controller with SMES is used for the purpose of minimization of f and P deviations. The different tunable parameters of the PID controller and those of the SMES are tuned by a novel quasi-oppositional harmony search algorithm. Performance study of the IHDG power system model is carried out under different perturbation conditions. The results demonstrate minimum f and P deviations may be achieved by using the proposed fuzzy logic based PID controller along with SMES.     

Core–shell NTC materials with low thermal constant and high resistivity for wide-temperature thermistor ceramics

Core–shell structures have been proposed to improve the electrical properties of negative-temperature coefficient (NTC) thermistor ceramics. In this work, Al₂O₃-modified Co_1.5Mn_1.2Ni_0.3O₄ NTC thermistor ceramics with adjustable electrical properties were prepared through citrate-chelation followed by conventional sintering. Co_1.5Mn_1.2Ni_0.3O₄ powder was coated with a thin Al₂O₃ shell layer to form a core–shell structure. Resistivity (ρ) increased rapidly with increasing thickness of the Al₂O₃ layer, and the thermal constant (B) varied moderately between 3706 and 3846 K. In particular, Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ ceramic with 0.08 wt% Al₂O₃ showed the increase of ρ double, and the change in its B was less than 140 K. The Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ NTC ceramics showed high stability, and their grain size was relatively uniform due to the protection offered by the shell. The aging coefficient of the ceramic was less than 0.2% after aging for 500 hours at 125°C. Taken together, the results indicate that as-prepared Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ NTC ceramics with a core–shell structure may be promising candidates for application as wide-temperature NTC thermistor ceramics.     

大口径光学元件装夹转运结构设计及分析

为了实现大口径光学元件的安全装夹、转运,通过光学元件开槽与不开槽两种装夹方式的分析,得出开槽夹紧转运方式将带来微裂纹、应力集中、成本高等缺陷,提出了利用摩擦力克服光学零件的重力和惯性力的低应力装夹转运方案。通过对光学元件低应力夹紧结构设计,并利用有限元分析方法,得到不开槽装夹方式下,光学元件的最大主应力为1.11 MPa,最大切应力为0.73 MPa,远低于光学元件破坏的强度极限,且受力均匀,无应力集中现象。     

Viscoelastic Behavior of Synthesized Liquid Soaps and Surface Activity Properties of Surfactants

In the present work, a rheological study of liquid soaps prepared from different mixture of surfactants as a function of surfactant type and concentration was performed. The curves of shear stress vs. shear rate and viscosity vs. shear rate were recorded at constant temperature, 294 ± 0.1 K. The surface activity properties were also studied. The results of the study showed that values of surface tension, γ, were in the range 31–40 mN m⁻¹ and the critical micelle concentration (CMC), was of the order 10⁻⁴ mol L⁻¹. The calculated maximum surface excess, Γ_max, varied from 2.40 to 3.66 μmol m⁻², while minimum area per molecule, A_min, varied from 41.1 (for amphoterics) to 81.4 Ų (for nonionic surfactants). The standard free energy of micellization, −29.8 and −29.3 kJ mol⁻¹ for anionic and amphoteric surfactants, respectively, were while values for nonionic surfactants varied between −31.8 and − 30.3 kJ mol⁻¹. The free energy of adsorption, was the lowest for amphoteric surfactants (−37.9 kJ mol⁻¹), followed by anionics (−40.4 kJ mol⁻¹) and nonionics (−43.34 to −46.84 kJ mol⁻¹), indicating that micellization process is spontaneous in the examined medium. The synthetized liquid soaps show pseudoplastic behavior and they achieved pipe flow. The results of this research indicate that flow behavior was affected significantly by the ionic charge of the surfactant and the ionic strength of the formulation, suggesting that the flow behavior could be changed by manipulating the choice of the surfactant and salinity. The pH value of all liquid soaps examined were weakly acidic, in the range of 5.0–6.4.     

Stress distribution in thick-walled cylinder due to non-uniform radial pressure on the example of reinforcement corrosion in concrete

This paper presents an analytical solution to the non-uniform pressure on thick-walled cylinder. The formulation is based on the linear elasticity theory (plain strain) and stress function method. As an example, the proposed solution is used to model the stress distribution due to non-uniform steel reinforcement corrosion in concrete. The model is formulated considering different scenarios of corrosion pressure distribution. It is validated against the finite element model for different cases of non-uniform pressure distributions. The results show that the corrosion-induced cracks are likely to start just beyond the anodic zone. This is confirmed by the experimental tests on concrete cylinder exposed to non-uniform accelerated corrosion of steel reinforcement. The model can be effectively used to calculate the distribution of corrosion-induced stresses in concrete.     

公路隧道喷射混凝土套拱加固结构力学特性

为研究喷射混凝土套拱加固前后二次衬砌与混凝土套拱的受力状况,依托陕西汉中至留坝段八里关隧道,运用有限元软件建立隧道混凝土结构套拱加固分析模型,并通过现场监测获取二次衬砌与套拱间的接触压力、套拱格栅拱架钢筋应力、套拱混凝土应力,将数值模拟结果与现场测试结果相结合,得出套拱结构的一般受力变化规律。结果表明:套拱加固前衬砌结构的最不利荷载位置位于施工缝附近的拱顶、拱肩与拱脚处; 由于衬砌局部变形与温度应力的影响,套拱混凝土应力变化呈现反复“上升-下降-上升”最后趋于稳定的特点; 套拱的作用是控制二次衬砌的进一步变形,套拱施作后所承受荷载较小,套拱反作用力远小于围岩作用于衬砌的应力,在应力计算中不应将衬砌与套拱作为整体计算; 套拱结构数值模拟所得的结果与现场测试套拱结构内力(轴力、弯矩)的大小及分布相似度高,但在衬砌裂损严重部位,数值模拟所得结果误差较大,应以现场测试结果为准。     

Crystallization and spectroscopic properties in Er3+ doped oxyfluorogermanate glass ceramics containing Na

The Er³⁺ doped oxyfluorogermanate glasses, with a composition containing Na element, were synthesized by the conventional melting–quenching technique. When Na element was introduced into the composition of oxyfluorogermanate glass, the crystals behavior was investigated in details. Depending on the annealing procedure supplied, thermal annealing of precursor glasses in the system GeO₂/BaF₂/AlF₃/Na₂O/NaF/ZnO/GdF₃/ErF₃ led to the precipitation of different crystal phase nanocrystals. It was confirmed the nanocrystals in GC600 is orthorhombic NaBaAlF₆ which led to enhance obviously in the UC luminescence of Er³⁺. However, the nanocrystals in G585 led to decrease in the UC luminescence, which indicated few Er ions enter into the lattice of this nanocrystal phase. The reason of the decrease in UC emission intensity of GC585 was analyzed.     

Thermal and transport properties of as-grown Ni-rich TiNi shape memory alloys

Electrical resistivity, Seebeck coefficient, specific heat and thermal conductivity measurements on the Ti_50−xNi_50+x (x = 0.0–1.6 at.%) shape memory alloys are performed to investigate their thermal and transport properties. In this study, anomalous features are observed in both cooling and heating cycles in all measured physical properties of the slightly Ni-rich TiNi alloys (x ≤ 1.0), corresponds to the transformation between the B19′ martensite and B2 austenite phases. Besides, the transition temperature is found to decrease gradually with increasing Ni content, and the driving force for the transition is also found to diminish slowly with the addition of excess Ni, as revealed by specific heat measurements. While the signature of martensitic transformation vanishes for the Ni-rich TiNi alloys with x ≥ 1.3, the characteristics of strain glass transition start to appear. The Seebeck coefficients of these TiNi alloys were found to be positive, suggesting the hole-type carriers dominate the thermoelectric transport. From the high-temperature Seebeck coefficients, the estimated value of Fermi energy ranges from ∼1.5 eV (Ti_48.4Ni_51.6) to ∼2.1 eV (Ti₅₀Ni₅₀), indicating the metallic nature of these alloys. In addition, the thermal conductivity of the slightly Ni-rich TiNi alloys with x ≤ 1.0 shows a distinct anomalous feature at the B19′ → B2 transition, likely due to the variation in lattice thermal conductivity.     

Manganese ferrite-polyaniline hybrid materials: Electrical and magnetic properties

Magnetic MnFe₂O₄ nanopowders were synthesized by an original solvothermal method in the absence and in the presence of tetra-n-butylammonium bromide (TBAB) and Tween 80 (TW) as surfactants. Manganese ferrite/polyaniline (PANI) hybrid materials were synthesized by in situ polymerization of aniline on the surface of MnFe₂O₄ using ammonium persulfate as oxidant. The purpose of the study was to investigate the influence of the two surfactants on the properties of the MnFe₂O₄ powders and of their composites with PANI. The specific surface area, the cumulative surface area of pores and the cumulative volume of pores are influenced by the nature of surfactant in case of MnFe₂O₄ powders and are higher by comparison to those of the MnFe₂O₄/PANI hybrid materials. The values of saturation magnetization in case of MnFe₂O₄ powders are higher than those of the hybrid materials and are not influenced by the surfactant nature. These features revealed that MnFe₂O₄ powders can be efficiently used as adsorbents for the purification of wastewaters. The values of the electrical conductivity of the composites exhibit a significant increase in comparison to the MnFe₂O₄ powders and depend on the surfactant nature. The highest value of electrical conductivity was achieved by the composite obtained using Tween 80 as surfactant (σ_DC = 54.5·10^?5S?m^?1) which was close to that of PANI (σ_DC = 61.2·10^?5 S?m^?1). The fact that the magnetic and electric properties of the synthesized MnFe₂O₄/PANI composites can be changed by design, demonstrate the high potential of these materials to be used in magneto-electric applications.     

Static and free vibration analysis of functionally graded plates based on a new quasi-3D and 2D shear deformation theories

In this study, two dimensional (2D) and quasi three-dimensional (quasi-3D) shear deformation theories are presented for static and free vibration analysis of single-layer functionally graded (FG) plates using a new hyperbolic shape function. The material of the plate is inhomogeneous and the material properties assumed to vary continuously in the thickness direction by three different distributions; power-law, exponential and Mori–Tanaka model, in terms of the volume fractions of the constituents. The fundamental governing equations which take into account the effects of both transverse shear and normal stresses are derived through the Hamilton's principle. The closed form solutions are obtained by using Navier technique and then fundamental frequencies are found by solving the results of eigenvalue problems. In-plane stress components have been obtained by the constitutive equations of composite plates. The transverse stress components have been obtained by integrating the three-dimensional stress equilibrium equations in the thickness direction of the plate. The accuracy of the present method is demonstrated by comparisons with the different 2D, 3D and quasi-3D solutions available in the literature.