积层板的制造方法

概述了积层板的开发背景、制造工艺和最近的开发动向。     

非线性扩频序列的三项式特性

讨论了三类非线性扩频序列(GMW序列、No序列和Kasami序列)的三项式特性，利用这三类序列的迹表示，证明了GMW序列、No序列和Kasami序列均具有正则三项式对。     

Effect of Stoichiometry on Properties of Rare-Earth-Based Hydrogen Storage Alloy for Nickel-Metal Hydride Secondary Battery

Effect of stoichiometry on microstructures, electrochemical properties and PCT characteristics of the alloys MI(Ni0.71Co0.15-Al0.06Mn0.08)x (MI=Lanthanum-rich Michmetal, x=4.6~5.2) have been investigated. The lattice constants a, c, and cellvolumes of non-stoichiometric alloys are bigger than those of the stoichiometric alloy. With the increasing stoichiometry x,the value of a decreases, and the value of c and cell volume increases except for those of the stoichiometric alloy; the plateaupressure of PCT curve, discharge capacity and cycling stability all increase. The alloy with x=5.2 shows the highest dischargecapacity and the best cycling stability among the studied alloys.     

Investigation into polishing process of CVD diamond films

A new technique used for polishing chemical vapor deposition (CVD) diamond films has been investigated, by which rough polishing of the CVD diamond films can be achieved efficiently. A CVD diamond film is coated with a thin layer of electrically conductive material in advance, and then electro-discharge machining (EDM) is used to machine the coated surface. As a result, peaks on the surface of the diamond film are removed rapidly. During machining, graphitization of diamond enables the EDM process to continue. The single pulse discharge shows that the material of the coated layer evidently affects removal behavior of the CVD diamond films. Compared with the machining of ordinary metal materials, the process of EDM CVD diamond films possesses a quite different characteristic. The removal mechanism of the CVD diamond films is discussed.     

烧结NdFeB合金中的夹杂物

使用金相显微镜、扫描电镜及Ｘ射线能谱和波谱观察并分析了ＮｄＦｅＢ烧结材料中夹杂物的形态、数量和组成。磁粉制备后立即烧结的ＮｄＦｅＢ磁体中的夹杂物是氧化钕；而在不同环境条件下放置后的ＮｄＦｅＢ粉再烧结的材料中发现，除了氧化钕的夹杂物外，还有钕的氮化物及钕的氮氧复合夹杂物。同时还论讨了这些夹杂物对于ＮｄＦｅＢ材料磁性能的影响。     

烧结工艺对液相合成（SrPb）TiO3基陶瓷热敏特性影响的研究

本文在液相合成（ＳｒＰｂ）ＴｉＯ３粉的基础上，研究了升温速率、保温时间、烧结温度及降温方式对（ＳｒＰｂ）ＴｉＯ３基陶瓷的Ｖ型ＰＴＣ热敏特性的影响。实验表明：升温速率对其热敏特性影响不大，保温时间和烧结温度的作用是一致的，具有一最佳范围。而降浊方式对材料的热敏特性影响较大。综合各因素的影响，本配方中，样品的烧结制度定为：以２００℃／ｈ的速率升温，在１２５０℃保温１ｈ，炉冷至９５０℃，保温０．５ｈ，再     

PP／SiO2／SBS共混复合材料性能的研究

通过加入增强剂、增韧剂、抗氧剂等添国剂可改善聚丙烯力学性能。以ＳｉＯ２为填料，丁苯橡胶（ＳＢＳ）为增韧剂，探讨ＳｉＯ２、丁苯橡胶含量对共混体系强度、韧性的影响，结果表明，在ＳＢＳ含量大于５％、ＳｉＯ２一小于１０％的范围内，可使ＰＰ／ＳｉＯ２／ＳＢＳ复合的拉伸弹性模量和冲击强度明显提高，其力学性能均为均衡。     

氢电弧等离子体法制备的纳米镍铈粒子的催化特性

利用氢电弧等离子法制备具有储氢特性纳米镍铈粒子，并在气相苯加氢反应中研究了其催化特性，发现其催化活性与储氢特性及表面层中ＮｉＣｅ合金存在有关，且具有高的选择性和热稳定性，这与纳米粒子独特的结构及铈的加入有关。     

低频电脉冲采油工程设备的开发与应用

低频电脉冲采油技术是通过升压、整流、充电等电路将电能蓄积在电容器中,通过触发电路,使能量瞬时释放,在井内液体中产生震动波,作用于地层,改善地层的渗流状况,达到提高采收率的目的。Ⅰ型设备在双河油田应用11井次,成功率72%;Ⅱ型设备在古城油田应用10井次,成功率90%。主要是由于Ⅰ型设备关键部件在处理油井时要放在井下,受高温、高压的影响及井下空间的限制,设备稳定性差、寿命短、能量小、效果差;Ⅱ型设备解决了上述问题,从而提高了试验成功率。     

秸杆材料用作草皮栽培基质的研究

本文介绍了秸杆毡的成型工艺 ,通过植物所需的水、肥料和空气三种因素对秸杆毡的化学和物理性能进行了研究 ,该材料可被用作草皮栽培基质