Complex study of protective Cr3C2–NiAl coatings deposited by vacuum electro-spark alloying,pulsed cathodic arc evaporation,magnetron sputtering,and hybrid technology

Coatings were obtained by vacuum electro-spark alloying (VESA), pulsed cathodic arc evaporation (PCAE), magnetron sputtering (MS) techniques and VESA-PCAE-MS hybrid technology using Cr₃C₂–NiAl electrodes. The structure of the coatings was analyzed using scanning and transmission electron microscopy, X-ray diffraction and energy-dispersive spectroscopy. Mechanical properties were determined by nanoindentation, while tribological properties were assessed using pin-on-disk tribometer. Corrosion resistance was estimated by voltammetry in 1 N H₂SO₄ and 3.5%NaCl solutions. Oxidation resistance tests were performed at 800°С in air. The VESA coating had the highest thickness, low friction coefficient and high wear resistance. PCAE coating demonstrated the highest hardness (24 GPa) and elastic recovery (59%), oxidation resistance and superior corrosion resistance both in 1 N H₂SO₄ (i_corr = 70 μА/cm²) and 3.5%NaCl (i_corr = 0.74 μА/cm²) solutions. The MS coating had average mechanical properties and low corrosion current density (71 μА/cm²) in 1 N H₂SO₄. Deposition of coatings using VESA-PCAE-MS hybrid technology led to an increase in corrosion and oxidation resistance at least by 1.5 times in comparison with the VESA coating.     

The effect of particle size distribution on the microstructure and properties of Al2O3 ceramics formed by stereolithography

Stereolithography (SL) shows advantages for preparing alumina-based ceramics with complex structures. The effects of the particle size distribution, which strongly influence the sintering properties in ceramic SL, have not been systematically explored until now. Herein, the influence of the particle size distribution on SL-manufactured alumina ceramics was investigated, including bending strength at room temperature, post-sintering shrinkage, porosity, and microstructural morphology. Seven particle size distributions of alumina ceramics were studied (in μm/μm: 30/5, 20/3, 10/2, 5/2, 5/0.8, 3/0.5, and 2/0.3); a coarse:fine particle ratio of 6:4 was maintained. At the same sintering temperature, the degree of sintering was greater for finer particle sizes. The particle size distribution had a larger influence on flexural strength, porosity and shrinkage than sintering temperature when the particle size distribution difference reached 10-fold but was weaker for 10 μm/2 μm, 5 μm/2 μm and 5 μm/0.8 μm. The sintering shrinkage characteristics of cuboid samples with different particle sizes were studied. The use of coarse particles influenced the accuracy of small-scale samples. When the particle size was comparable to the sample width, such as 30 μm/5 μm and 5 mm, the width shrinkage was consistent with the height shrinkage. When the particle size was much smaller than the sample width, such as 2 μm/0.3 μm and 5 mm, the width shrinkage was consistent with the length shrinkage. The results of this study provide meaningful guidance for future research on applications of SL and precise control of alumina ceramics through particle gradation.     

基于PBFT区块链技术的电网企业仓储系统

提出了一种基于实用拜占庭容错(PBFT)算法的区块链技术,首先对传统的实用拜占庭容错算法原理进行了阐述,该传统算法包含前期、需求、预准备、准备、确认、答复6个阶段,但传统算法具有实时性差、缺乏惩罚机制、带宽高的缺点。针对出现的这些问题,又对传统算法进行了改进,具体涉及记账节点、共识过程以及视图切换过程。通过测试进一步证明了该改进算法的实用性,并将该算法应用于电网企业中,构建的虚拟仓库实现了联储联备,降低了库存资金的耗费,并且提高了电网企业库存管理的效率。     

外墙保温系统中粘结材料的检测技术分析

选择了几份典型的外墙外保温系统标准,通过对这几份标准中胶粘剂和抹面胶浆的成型和检测方法的比较,分析了现有检测技术的优劣,并结合工作实践提出了建议。     

基于熵权TOPSIS的工程咨询机构BIM技术应用能力评价

构建工程咨询机构BIM技术应用能力评价的指标体系,提出改进的熵权TOPSIS评价模型,以4个典型的工程咨询单位为例,进行BIM技术运用能力评价。研究表明,BIM行业的整体水平已经有了明显的提升,但是区域间的发展还存在一定差距。     

增材制造技术在超高膨胀封隔器中的应用

石油和天然气行业不断关注增材制造技术在航空航天和汽车行业的应用发展。研发了利用增材制造技术的超高膨胀封隔器,该封隔器的支承环系统由增材制造。增材制造设计大幅减少了支承系统的构件数量,同时显著提高了膨胀能力和额定压力。密封元件系统与增材制造支承环安装在一起,提供了极端膨胀比、零挤压间隙和对不规则孔的良好适应性。分析和测试结果表明:直径膨胀比高达111%,与常规封隔器相比,提高50%以上; 至少涵盖5种线重的套管(外径相同); 在148.89 ℃的温度下,密封元件能够保持压力68.95 MPa。介绍了增材制造技术、增材制造支承环概念、增材制造材料力学性能、密封元件系统优化和测试情况,以期给我国的完井作业提供借鉴。     

基于物联网的智慧林业可持续发展策略研究

随着我国科技的不断进步,在“互联网+”大数据的背景下,林业的智慧化发展是必经之路。虽然我国智慧林业的发展已经取得了一定的突破,但是仍然存在着许多问题。基于此,文章在物联网技术的基础上,对智慧林业的可持续发展策略进行探讨。     

Lean production system design for fishing net manufacturing using lean principles and simulation optimization

Value stream mapping (VSM) is a useful tool for describing the manufacturing state, especially for distinguishing between those activities that add value and those that do not. It can help in eliminating non-value activities and reducing the work in process (WIP) and thereby increase the service level. This research follows the guidelines for designing future state VSM. These guidelines consist of five factors which can be changed simply, without any investment. These five factors are (1) production unit; (2) pacemaker process; (3) number of batches; (4) production sequence; and (5) supermarket size. The five factors are applied to a fishing net manufacturing system. Using experimental design and a simulation optimizing tool, the five factors are optimized. The results show that the future state maps can increase service level and reduce WIP by at least 29.41% and 33.92% respectively. For the present study, the lean principles are innovatively adopted in solving a fishing net manufacturing system which is not a well-addressed problem in literature. In light of the promising empirical results, the proposed methodologies are also readily applicable to similar industries.     

Design of delayed reconfigurable manufacturing system based on part family grouping and machine selection

To improve the convertibility of reconfigurable manufacturing system (RMS), the concept of delayed reconfigurable manufacturing system (D-RMS) was proposed. RMS and D-RMS are both constructed around part family. However, D-RMS may suffer from ultra-long system problem with unacceptable idle machines using generic RMS part families. Besides, considering the complex basic system structure of D-RMS, machine selection of D-RMS should be addressed, including dedicated machine, flexible machine, and reconfigurable machine. Therefore, a system design method for D-RMS based on part family grouping and machine selection is proposed. Firstly, a part family grouping method is proposed for D-RMS that groups the parts with more former common operations into the same part family. The concept of longest relative position common operation subsequence (LPCS) is proposed. The similarity coefficient among the parts is calculated based on LPCS. The reciprocal value of the operation position of LPCS is adopted as the characteristic value. The average linkage clustering (ALC) algorithm is used to cluster the parts. Secondly, a machine selection method is proposed to complete the system design of D-RMS, including machine selection rules and the dividing point decision model. Finally, a case study is given to implement and verify the proposed system design method for D-RMS. The results show that the proposed system design method is effective, which can group parts with more former common operations into the same part family and select appropriate machine types.     

Distributed ledger technology in supply chains: a transaction cost perspective

With the emergence of distributed ledger technology (DLT), numerous practitioners and researchers have proclaimed its beneficial impact on supply chain transactions in the future. However, the vast majority of DLT initiatives are discontinued after a short period. With the full potential of DLT laying far down the road, especially managers in supply chain management (SCM) seek for short-term cost-saving effects of DLT in order to achieve long-term benefits of DLT in the future. However, the extant research has bypassed grounding long-term as well as short-term effects of DLT on supply chain transaction with empirical data. We address this shortcoming, following an abductive research approach and combining empirical data from a multiple case study design with the corresponding literature. Our study reveals that the effects of DLT on supply chain transactions are two-sided. We found six effects of DLT solutions that have a cost-reducing or cost avoidance impact on supply chain transactions. In addition, we found two effects that change the power distribution between buyers and suppliers in transactions and a single effect that reduces the dependency of supply chain transactions on third parties. While cost-reducing and avoidance as well as dependency-reducing effects are positive effects, the change in power distribution might come with disadvantages. With these findings, the paper provides the first empirical evidence of the impact of DLT on supply chain transactions, which will enable managers to improve their assessment of DLT usage in supply chains.