Structure and phase-composition of Ti-doped gas atomized Raney-type Ni catalyst precursor alloys

Raney-type Ni precursor alloys containing 75 at.% Al and doped with 0, 0.75, 1.5 and 3.0 at.% Ti have been produced by a gas atomization process. The resulting powders have been classified by size fraction with subsequent investigation by powder XRD, SEM and EDX analysis. The undoped powders contain, as expected, the phases Ni₂Al₃, NiAl₃ and an Al-eutectic. The Ti-doped powders contain an additional phase with the TiAl₃ DO₂₂ crystal structure. However, quantitative analysis of the XRD results indicate a far greater fraction of the TiAl₃ phase is present than could be accounted for by a simple mass balance on Ti. This appears to be a (Ti_xNi_1−x)Al₃ phase in which higher cooling rates favour small x (low Ti-site occupancy by Ti atoms). SEM and EDX analysis reveal that virtually all the available Ti is contained within the TiAl₃ phase, with negligible Ti dissolved in either the Ni₂Al₃ or NiAl₃ phases.     

Design and performance study of phase‐locked loop using fractional‐order loop filter

The present work reports the realization of an analog fractional‐order phase‐locked loop (FPLL) using a fractional capacitor. The expressions for bandwidth, capture range, and lock range of the FPLL have been derived analytically and then compared with the experimental observations using LM565 IC. It has been observed that bandwidth and capture range can be extended by using FPLL. It has also been found that FPLL can provide faster response and lower phase error at the time of switching compared to its integer‐order counterpart. Copyright © 2014 John Wiley & Sons, Ltd.     

Design guidelines for titania-silica-alumina ceramics with tuned anatase to rutile transformation

Titania-based ceramics with adjustable anatase-rutile fractions were obtained by milling of anatase, quartz and corundum precursors, uniaxial pressing and firing at 1100?°C. The influence of silica and alumina, combined with milling time and compaction pressure, was studied by design of experiments. The L9 orthogonal array with a three-level noise factor was employed. Firing of pure titania at 1100?°C yielded complete anatase to rutile transformation (ART), whereas stabilized samples show that an optimum amount of 9% silica and 33% alumina reduces phase transformation to only about 5?wt% rutile. An extended correlation matrix combined with analysis of variance (ANOVA) was applied to assess the combined effects of quartz, alumina, milling time and uniaxial compressing pressure on relative density, and anatase to rutile transformation. Results show absence of ART after milling, and controlled partial conversion of anatase to rutile after firing. Very good fitting was obtained by multivariate analysis on considering first and second order terms for dependence on silica contents and interactions between silica and each of the remaining factors, including milling time. This empirical dependence could be interpreted on a sound physicochemical basis, allowing the prediction of suitable compositions and processing conditions to obtain rutile-free samples by conventional ceramic processing, and to design ceramic samples with controlled fractions of anatase and rutile.     

致密油藏注天然气提高采收率研究现状

随着我国石油需求量不断增加,致密油藏的开发也愈发重要。如何高效开发致密油藏是一项重点难点,其中致密油藏注天然气提高采收率是一个极具潜力的研究方向。因此,本文着重介绍以天然气作为能量补充介质在国内外的研究现状和应用现状,并且从两相特征等方面总结了理论研究中的一些机理,对致密油藏注天然气提高采收率的发展前景进行了一定的展望。     

A miniature triaxial apparatus for investigating the micromechanics of granular soils with in situ X-ray micro-tomography scanning

The development of a miniature triaxial apparatus is presented. In conjunction with an X-ray micro-tomography (termed as X-ray μCT hereafter) facility and advanced image processing techniques, this apparatus can be used for in situ investigation of the micro-scale mechanical behavior of granular soils under shear. The apparatus allows for triaxial testing of a miniature dry sample with a size of \mathrm{8}\hspace{0.17em}\mathrm{mm}\times \mathrm{16}\hspace{0.17em}\mathrm{mm} (diameter \times height). In situ triaxial testing of a 0.4–0.8 mm Leighton Buzzard sand (LBS) under a constant confining pressure of 500 kPa is presented. The evolutions of local porosities (i.e., the porosities of regions associated with individual particles), particle kinematics (i.e., particle translation and particle rotation) of the sample during the shear are quantitatively studied using image processing and analysis techniques. Meanwhile, a novel method is presented to quantify the volumetric strain distribution of the sample based on the results of local porosities and particle tracking. It is found that the sample, with nearly homogenous initial local porosities, starts to exhibit obvious inhomogeneity of local porosities and localization of particle kinematics and volumetric strain around the peak of deviatoric stress. In the post-peak shear stage, large local porosities and volumetric dilation mainly occur in a localized band. The developed triaxial apparatus, in its combined use of X-ray μCT imaging techniques, is a powerful tool to investigate the micro-scale mechanical behavior of granular soils.     

Effect of spatial constraints on the phase evolution of YFeO3-based nanopowders under heat treatment of glycine-nitrate combustion products

Formation and structural transformations of yttrium orthoferrite crystals have been studied using X-ray diffractometry, Mössbauer spectroscopy and transmission electron microscopy combined with electron microdiffraction. Said processes have been studied under heat treatment of glycine-nitrate combustion products. There have been identified formations of three structural yttrium orthoferrite modifications – amorphized hexagonal <h₁>-YFeO₃ (P6₃cm) and nanocrystalline hexagonal h₂-YFeO₃ (P6₃/mmc), as well as nanocrystalline orthorhombic o-YFeO₃ (Pbnm), which are selectively formed depending on available three-dimensional confinements. Based on the analysis of changes in the fluid and size composition formulation, it has been proposed mechanism for formation and transformation of YFeO₃ nanocrystals, including growth stage of h₂-YFeO₃ crystals due to amorphized phase of <h₁>-YFeO₃ up to critical size of about 15?nm and their subsequent transformation into orthorhombic form o-YFeO₃.     

Temperature- and frequency-dependent hysteresis scaling behaviour and phase transitions in a [001]c 0.73Pb(Mg1/3Nb2/3)O3-0.27PbTiO3 single crystal

The dielectric properties and bipolar polarization-electric field (P-E) and strain-electric field (S-E) dynamic hysteresis of a relaxor [001]_c 0.73Pb(Mg_1/3Nb_2/3)O₃-0.27PbTiO₃ (PMN-0.27PT) single crystal were investigated to reveal more details of the temperature-induced phase transitions. Different linear scaling relations for ferroelectric hysteresis area <A>, coercive field E_c, saturation polarization P_s and remnant polarization P_r versus temperature τ were measured in different temperature regions. For each measurement frequency f, all hysteresis parameters were found to decrease linearly with temperature in the temperature range of the single rhombohedral (R) phase or tetragonal (T) phase, and the rate of decrease in the T phase was observed to be much larger than the corresponding rate in the R phase. In the temperature range near the R-T phase transition, the exponent α in the power law <A>∝f ^α for the R phase was found to be smaller than that for the T phase, and the magnitude of α depended strongly on temperature when the crystal was in the R-T coexisting phase state. Our experimental and theoretical results indicate that the difference in the activation energy and dipole moment in the R and T phases may lead to the observed discrepancy for the P-E and S-E hysteresis behaviour in different temperature regions.     

Doping-free hybrid white organic light-emitting diodes with fluorescent blue,phosphorescent green and red emission layers

Industrialized white organic light-emitting diodes (OLEDs) currently require host-guest doping, a complicated process necessitating precise control of the guest concentration to get high efficiency and stability. Two doping-free, hybrid white OLEDs with fluorescent blue, and phosphorescent green and red emissive layers (EMLs) are reported in this work. An ultra-thin red phosphorescent EML was situated in a blue-emitting electron transport layer (ETL), while the ultra-thin green phosphorescent EML was placed either in the ETL (Device 1), or the hole transport layer (HTL) (Device 2). Device 2 exhibits higher efficiency and more stable spectrum due to the enhanced utilization of excitons by ultra-thin green EML at the exciton generation zone within the HTL. Values of current efficiency (CE), power efficiency (PE), and CRI obtained for the optimized hybrid white OLEDs fabricated through a doping-free process were of 23.2 cd/A, 20.5 lm/W and 82 at 1000 cd/m², respectively.