水文学的研究方法与理论创新

回顾了水文学在其 30 0余年的形成和发展中曾出现过的若干引人入胜、富有启发性、对学科发展起着重要推动作用的研究成果 .论述了“假设”、“猜想”、“推理”、“比拟”、“综合”和“实验”等研究方法的运用在水文学理论创新中的重要作用 .     

Optical analysis of crack tip stress fields: a comparative study

Four optical techniques for evaluating stress intensity factors in opaque specimens are described in outline, and compared for both an artificial crack and a fatigue crack. The results are compared to a standard solution for the geometry considered. All the techniques gave acceptable results over a range of stress levels and crack lengths. The methods of caustics and strain gauges were less good, whilst photoelasticity gave consistent results over a wide range of stress levels. Comments on the ease of application and the resource implications are also made in order to assist practitioners.     

迭加与量化水印嵌入方案的比较及量化参数优化

分别研究了迭加法和量化法的隐蔽性和稳健性，并且提出了量化调制水印方案中的参数优化方法。对两类方法的分析比较表明，迭加法适用于在高频分量嵌入水印，而量化法适用于在低频分量嵌入水印。并以实验验证了这一结论。     

Error Concealment Based on Semantic Prioritization with Hardware‐Based Face Tracking

With video compression standards such as MPEG‐4, a transmission error happens in a video‐packet basis, rather than in a macroblock basis. In this context, we propose a semantic error prioritization method that determines the size of a video packet based on the importance of its contents. A video packet length is made to be short for an important area such as a facial area in order to reduce the possibility of error accumulation. To facilitate the semantic error prioritization, an efficient hardware algorithm for face tracking is proposed. The increase of hardware complexity is minimal because a motion estimation engine is efficiently re‐used for face tracking. Experimental results demonstrate that the facial area is well protected with the proposed scheme.     

利用UTD修正的MoM-PO混合算法研究

介绍了利用矩量法(MoM)和物理光学(PO)混合方法处理复杂线体结构的电磁散射问题，提出利用pulse基函数对线电流进行展开，使得处理复杂线体结构问题变得简化，并推导出一般的矩阵方程。然后针对PO在阴影区域失效等问题，利用UTD(一致性几何绕射)对该简化模型结构下的PO区域电流进行了修正，使得其应用范围得到扩展、计算精度得到提高。文中的实例结果与传统的MoM很好的一致，从而说明了该方法的有效性和精确性。     

Scale‐up and Spouting of Two‐Dimensional Beds

The objective of this paper is to present an analysis on the scale‐up procedure of two‐dimensional spouted beds. The task was carried out with three different beds measuring 0.15, 0.30 and 0.80 in width. The conditions of scale‐up were studied through geometrical similitude analysis. Some parameters of scale were adimensionalised, tested and validated in order to propose relationships capable of predicting values of dependent properties. Those relationships should be followed in a prototype of an equipment of industrial scale. The study permitted the development of correlations to predict values of maximum pressure drop, minimum spout velocity and maximum height of spouting.     

Relating the Morphology of Poly(p‐phenylene vinylene)/Methanofullerene Blends to Solar‐Cell Performance

The performance of bulk‐heterojunction solar cells based on a phase‐separated mixture of donor and acceptor materials is known to be critically dependent on the morphology of the active layer. Here we use a combination of techniques to resolve the morphology of spin cast films of poly(p‐phenylene vinylene)/methanofullerene blends in three dimensions on a nanometer scale and relate the results to the performance of the corresponding solar cells. Atomic force microscopy (AFM), transmission electron microscopy (TEM), and depth profiling using dynamic time‐of‐flight secondary ion mass spectrometry (TOF‐SIMS) clearly show that for the two materials used in this study, 1‐(3‐methoxycarbonyl)propyl‐1‐phenyl‐[6,6]‐methanofullerene (PCBM) and poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene vinylene] (MDMO‐PPV), phase separation is not observed up to 50 wt.‐% PCBM. Nanoscale phase separation throughout the film sets in for concentrations of more than 67 wt.‐% PCBM, to give domains of rather pure PCBM in a homogenous matrix of 50:50 wt.‐% MDMO‐PPV/PCBM. Electrical characterization, under illumination and in the dark, of the corresponding photovoltaic devices revealed a strong increase of power conversion efficiency when the phase‐separated network develops, with a sharp increase of the photocurrent and fill factor between 50 and 67 wt.‐% PCBM. As the phase separation sets in, enhanced electron transport and a reduction of bimolecular charge recombination provide the conditions for improved performance. The results are interpreted in terms of a model that proposes a hierarchical build up of two cooperative interpenetrating networks at different length scales.     

Insulating safety analysis of the hot-line sweeping robot

This paper presents a method of calculating the insulating safety distances for hot-line working robots at high voltage when dielectric is adulterated with conducts. Also, finite element method is adopted to calculate the electric field strength to find whether it is beyond the critical. The above methods have been applied to analyze the insulating safety of the robot for hot-line sweeping post insulators in a 220 KV substation. They have also been testified by experimentations.     

Conducting composites of poly(N‐vinylcarbazole), polypyrrole,and polyaniline with 13X‐zeolite

N‐vinylcarbazole (NVC) was polymerized by 13X zeolite alone in melt (65°C) or in toluene (110°C) and a poly(N‐vinylcarbazole) (PNVC)‐13X composite was isolated. Composites of polypyrrole (PPY) and polyaniline(PANI) with 13X zeolite were prepared via polymerization of the respective monomers in the presence of dispersion of 13X zeolite in water (CuCl₂ oxidant) and in CHCl₃ (FeCl₃ oxidant) at an ambient temperature. The composites were characterized by Fourier transform infrared analyses. Scanning electron microscopic analyses of various composites indicated the formation of lumpy aggregates of irregular sizes distinct from the morphology of unmodified 13X zeolite. X‐ray diffraction analysis revealed some typical differences between the various composites, depending upon the nature of the polymer incorporated. Thermogravimetric analyses revealed the stability order as: 13X‐zeolite > polymer‐13X‐zeolite > polymer. PNVC‐13X composite was essentially a nonconductor, while PPY‐13X and PANI‐13X composites showed direct current conductivity in the order of 10^?4 S/cm in either system. However, the conductivity of PNVC‐ 13X composite could be improved to 10^?5 and 10^?6 S/cm by loading PPY and PANI, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 913–921, 2006     

A Micellar Route to Ordered Arrays of Magnetic Nanoparticles: From Size‐Selected Pure Cobalt Dots to Cobalt–Cobalt Oxide Core–Shell Systems

Starting with Co‐salt‐loaded inverse micelles, which form if the diblock copolymer polystyrene‐block‐poly(2‐vinylpyridine) is dissolved in a selective solvent like toluene and CoCl₂ is added to the solution, monomicellar arrays of such micelles exhibiting a significant hexagonal order can be prepared on top of various substrates with tailored intermicellar distances and structure heights. In order to remove the polymer matrix and to finally obtain arrays of pure Co nanoparticles, the micelles are first exposed to an oxygen plasma, followed by a treatment in a hydrogen plasma. Applying in‐situ X‐ray photoelectron spectroscopy, it is demonstrated that: 1) The oxygen plasma completely removes the polymer, though conserving the original order of the micellar array. Furthermore, the resulting nanoparticles are entirely oxidized with a chemical shift of the Co 2p_3/2 line pointing to the formation of Co₃O₄. 2) By the subsequent hydrogen plasma treatment the nanoparticles are fully reduced to metallic Co. 3) By exposing the pure Co nanoparticles for 100 s to various oxygen partial pressures pequation/tex2gif-inf-5.gif, a stepwise oxidation is observed with a still metallic Co core surrounded by an oxide shell. The data allow the extraction of the thickness of the oxide shell as a function of the total exposure to oxygen (pequation/tex2gif-inf-7.gif × time), thus giving the opportunity to control the ferromagnetic–antiferromagnetic composition of an exchange‐biased magnetic system.