OPGW与普通地线构成的双地线系统中单相短路电流分流的计算

单相短路电流分布的准确计算对输电系统的安全有重要影响。文中说明了双侧消去法的特点,采用回路法对短路电流分布进行了量化计算和算例验证,将计算结果与双侧消去法的结果进行了比较,讨论了普通地线绝缘间隙不击穿情况下短路电流分布的变化。结果表明:回路法得到的短路电流分布与双侧消去法的结果一致,证明了采用回路法计算的结果是正确的;假定绝缘间隙不击穿时,相应线路段的光纤复合架空地线(optical fiber composite overhead ground wire,OPGW)要承受更大的电流,为实现OPGW与普通地线匹配,降低实际线路成本,绝缘间隙整定时,确保绝缘间隙击穿有重大的现实意义。     

编码TCP的建模与性能分析

研究了无线网络端到端分组丢失和编码纠错对TCP协议工作过程的影响机制,基于三维Markov链建模描述TCP拥塞窗口和可用窗口的变迁过程,在忽略慢启动阶段的条件下,以最大窗口尺寸、端到端分组丢失率和编码冗余系数为输入参数,通过数值计算求解编码TCP的吞吐率,据此定量分析影响编码TCP性能的因素。基于NS2的模拟实验结果表明基于Markov链的数值计算结果具有较高的准确度。     

多跳认知无线Mesh网络中频谱决策与路由的跨层设计

灵活高效的频谱共享技术能够实现频谱资源的最大化利用,有效地缓解了无线频谱紧缺的现状。在一个与TDMA/FDMA蜂窝网络共存的多跳认知无线Mesh网络环境下,基于覆盖式（Underlay）与机会式（Overlay）相结合的频谱共享机制,提出了一种有效的链路层频谱决策与网络层路由的跨层设计方案。仿真结果表明,该方案比基于最小跳数的随机信道选择算法在网络端到端传输性能上有显著的优势。     

Agitation of Herschel–Bulkley fluids with the Scaba–anchor coaxial mixers

The design of the coaxial mixers depends on many interrelated parameters including the geometry and dimensions of the mixing vessel, the location and type of the impellers, speed ratio, impeller diameter, rotation mode, and fluid rheology. No study has been reported in the literature regarding the mixing performance of the coaxial mixers in the agitation of yield-pseudoplastic fluids. Thus, the main objective of this study was to evaluate the performance of a Scaba–anchor coaxial mixer (a novel configuration) in the mixing of xanthan gum solutions (yield-pseudoplastic fluids). The Herschel–Bulkley model was used to describe the rheological behavior of the xanthan gum solutions. To develop new correlations for the generalized Reynolds and power numbers of the coaxial mixers employed in the agitation of this class of non-Newtonian fluids, we utilized numerous experimental and computational fluid dynamics (CFD) data. The new correlations were tested successfully at different operating conditions (e.g. speed ratio, fluid rheology, and operation mode).     

Throughput oriented forwarders selection analysis for opportunistic routing in wireless mesh network

Opportunistic routing explicitly takes advantage of the broadcast nature of wireless communications by using a set of forwarders to opportunistically perform packet forwarding. A key issue in the design of opportunistic routing protocols is the forwarder list selection problem. This paper proposes a novel routing metric which shows the end-to-end throughput and a corresponding throughput oriented opportunistic routing forwarder-selecting algorithm throughput oriented forwarders selection (TOFS) through analyzing forwarding characteristics of forwarders. The algorithm puts forward a constraint mechanism that controls the number of forwarders by constraint of throughput for forwarders selection, achieving a better balance between number of forwarders and effective link stability by introducing the factor of transmission time. Simulation results show that the algorithm can improve the network end-to-end throughput effectively over existing methods.     

基于有限元算法的戴罩天线辐射特性快速求解

提出一种基于矢量有限元算法来分析天线罩与天线系统辐射特性的等效方法。在传统有限元方法中,需对整个求解区域进行网格剖分。由于天线局部细小结构的电尺寸与整个求解区域有较大的差距。因此,在网格划分时容易导致剖分奇异性的出现以至于无法顺利剖分或矩阵无法求解。为避免上述问题并提高计算效率,文中将原求解区域进行区域分解,天线在子区域中单独求解,再将子区域边界得到的场值提取出来,同其他求解区域进行耦合,求解耦合矩阵,从而得到整体区域的场值,然后计算所需的增益等辐射参数。并快速准确地得到整个系统计算模型的辐射特性。     

Performance evaluation of an IEEE 802.11g mesh network with multiradio nodes

Wireless mesh networks are usually formed by self‐organized nodes and characterized by high reliability and modularity, low‐cost deployment, and easiness of reconfigurability. In order to improve wireless mesh network performance, several approaches have been recently proposed. Among them, one promising solution seems to be the multiradio interface approach where nodes forming the mesh network are equipped with more than one radio interface. The aim of this paper is to provide an IEEE 802.11 distributed coordination function analytical model to study the behavior of single‐hop multi‐interface mesh networks in which nodes use a uniform random interface selection strategy to identify the radio interface to be used. The accuracy of the proposed analytical approach is validated by comparing analytical predictions with simulation results under actual conditions. Copyright © 2011 John Wiley & Sons, Ltd.     

A high‐performance switch architecture based on mesh of trees

With emergence of various new Internet‐enabled devices, such as tablet PCs or smart phones along with their own applications, the traffic growth rate is getting faster and faster these days and demands more communication bandwidth at even faster rate than before. To accommodate this ever‐increasing network traffic, even faster Internet routers are required. To respond for these needs, we propose a new mesh of trees based switch architecture, called MOTS(N) switch. In addition, we also propose two more variations of MOTS(N) to further improve it. MOTS(N) is inspired by crossbar with crosspoint buffers. It forms a binary tree for each output line, where each gridpoint buffer ? ? Because the fabric of MOTS(N) switch is not pure crossbar, we call the buffers in the same location in pure crossbar gridpoint buffers. Details will be presented in the following sections.
is a leaf node and each internal node is 2‐in 1‐out merge buffer § § 2‐in 1‐out merge buffer can accommodate two memory writes and one memory read simultaneously by using its modularized architecture 31 .
emulating FIFO queues. Because of this FIFO characteristic of internal buffers, MOTS(N) ensures QoS like FIFO output‐queued switch. The root node of the tree for each output line is the only component connected to the output port where each cell is transmitted to output port without any contention. To limit the number of buffers in MOTS(N) switch, we present one of its improved (practical) variations, IMOTS(N) switch, as well. For IMOTS(N) switch architecture, sizes of the buffers in the fabric are limited by a certain amount. As a downside of IMOTS(N), however, every cell should go through log ₂N + 1 number of buffers in the fabric to be transmitted to the designated output line. Therefore, for even further improvement, IMOTS(N) with cut‐through, denoted as IMOTS‐CT(N), is also proposed in this paper. In IMOTS‐CT(N) switch, the cells can cut through one or more empty buffers to be transferred from inputs to outputs with simple 1 or 2 bit signal exchanges between buffers. We analyze the throughput of MOTS(N), IMOTS(N), and IMOTS‐CT(N) switches and show that they can achieve 100% throughput under Bernoulli independent and identically distributed uniform traffic. Our quantitative simulation results validate the theoretical analysis. Copyright © 2012 John Wiley & Sons, Ltd.     

Integration of microbial fuel cell with independent membrane cathode bioreactor for power generation,membrane fouling mitigation and wastewater treatment

A microbial fuel cell (MFC) was integrated with flat sheet membrane bioreactor (MBR) and studied for electricity generation, membrane fouling mitigation and artificial wastewater treatment. The cell potential was ∼0.2 V with 100 Ω external load during closed circuit operation. Batch tests identified that the sludge properties and aeration in cathodic chamber were the main affecting factors on electricity generation. Integration of microbial fuel cell can significantly alleviate membrane fouling, under closed circuit condition, membrane filtration lasted 21 days – 27 days and under the open circuit condition it lasted only 13 days - 15 days, before the transmembrane pressure (TMP) reached 0.03 MPa. The calculated electrostatic repulsion force between membrane surface and membrane foulant was about 2.5 × 10⁻¹⁴ N in this integrated reactor. The chemical oxygen demand (COD), ammonia nitrogen, phosphorus and offensive smell could be effectively removed by the sequential anaerobic-aerobic treatment system. The effluent pH was neutral and turbidity was very low.     

浅谈网格密度对叶片频率的影响

采用有限元法对整圈叶片一阶频率进行分析时,由于叶片网格划分的不同,可能对频率计算造成较大影响。通过研究叶片网格密度变化对整圈叶片一阶频率的影响,发现叶片径向网格密度变化对整圈叶片的一阶频率影响不大;叶片厚度方向网格密度最好不少于4层;弧形叶根轴向网格密度小于一定数值时计算结果相差很大。