撬装式油井热洗装置研制及应用效果评价

油井热洗是油田最常用的一种清蜡方法。靖安长6油藏是采油三厂的主力油藏,截至2004年底建成油井1064口,由于长6层原油含蜡量高,油井结蜡严重,通常采用常规热洗方法进行油井清蜡。存在以下两方面问题：一是常规油井热洗方法操作比较复杂,运行动力设施多,热洗费用较高；二是常规洗井油源均来自联合站或接转站,为不同层所采的混合原油,进入地层后,会对地层造成一定程度的伤害。为此,我们认真分析了现有油井热洗工艺的不足,查找了油井热洗费用高的影响因素,结合靖安油田长6油藏丰富的伴生气资源,自主研发了撬装式油井热洗装置,经过现场应用取得了较好的效果。     

后热处理对新型马氏体耐热钢焊缝性能的影响

针对电力施工过程中对具有冷裂倾向的马氏体型耐热钢焊后后热处理时机选择与标准存在差异，即是否必要在冷却至100-120℃恒温一段时间后再进行后热处理的问题，安排了一系列的试验对后热处理的最佳时机予以讨论，对热处理后的焊缝组织进行力学性能试验和金相分析，对冲击后的试样进行了断口分析。试验证明，后热处理时机的不同对马氏体耐热钢焊缝冲击韧度有比较大的影响，马氏体耐热钢的后热处理应在马氏体转变完全后开始较为合适。     

冷却水污垢及其对冷却器换热的影响

分析了冷却器的结垢机理 ,提出了冷却器污垢层、污垢热阻随运行时间的规律 ,以及污垢热阻与换热系数、换热面积的关系式 ,并通过算例阐述了污垢热阻对冷却器的影响程度 ,进而定性地分析了污垢热阻对空分装置的影响。     

ESW激波吹灰器在余热锅炉的应用

介绍了ESW激波吹灰器的工作原理及其在茂名分公司Ⅲ套催化裂化装置余热锅炉的应用情况。应用结果表明，使用ESW激波吹灰器吹灰效果明显，吹灰后余热锅炉排烟温度可下降29℃，过热蒸汽产量增加7t/h，锅炉自产饱和蒸汽产量增加2t/h，有效提高了余热锅炉的传热效率和过热能力，节能效果显著。对应用中出现的一些问题提出了改进建议。     

Pulsating Jet Impingement Heat Transfer Enhancement

This article presents results from a numerical study of pulsating jet impingement heat transfer. The motivation is to seek conditions offering a significant enhancement compared to steady flow impingement drying. The CFD software package FLUENT was used for simulating slot-type pulsating jet impingement flows with confinement. The parameter study included velocity amplitude ratio, mean jet velocity, and pulsation frequency. The distance from nozzle exit to surface was three times the hydraulic diameter of the nozzle. The Reynolds number based on the nozzle hydraulic diameter and jet temperature was 2,460 with a mean jet velocity of 30 m/s, which is the base case of the numerical experiments. Results showed that time-averaged surface heat transfer increased with increasing velocity amplitude for the same mean jet velocity. Large velocity amplitudes helped enhance heat transfer by two mechanisms: high jet velocity during the positive cycle and strong recirculating flows during the negative cycle. For the cases with different mean jet velocities but the same maximum velocity, time-averaged surface heat flux decreased with decreasing mean jet velocity. As for the effects of pulsation frequency, with high-velocity amplitude ratio, time-averaged surface heat fluxes were at the same level regardless of frequency. However, at low-velocity amplitude ratio, high frequency caused stronger recirculating flows resulting in greater heat transfer compared to the cases with a lower frequency.     

Flammability characteristics at applied heat flux levels up to 200 kW/m2

This paper documents the first of the two interrelated studies that were conducted to more fundamentally understand the scalability of flame heat flux, the motivation being that it has been reported that flame heat flux back to the burning surface in bench‐scale experiments is not the same as for large‐scale fires. The key aspect was the use of real scale applied heat flux up to 200kW/m² which is well beyond that typically considered in contemporary testing. The main conclusions are that decomposition kinetics needs to be included in the study of ignition and the energy balance for steady burning is too simplistic to represent the physics occurring. An unexpected non‐linear trend is observed in the typical plotting methods currently used in fire protection engineering for ignition and mass loss flux data for several materials tested and this non‐linearity is a true material response. Using measured temperature profiles in the condensed phase shows that viewing ignition as an inert material process is inaccurate at predicting the surface temperature at higher heat fluxes. The steady burning temperature profiles appear to be invariant with applied heat flux. This possible inaccuracy was investigated by obtaining the heat of gasification via the ‘typical technique’ using the mass loss flux data and comparing it to the commonly considered ‘fundamental’ value obtained from differential scanning calorimetry measurements. This comparison suggests that the ‘typical technique’ energy balance is too simplified to represent the physics occurring for any range of applied heat flux. Observed bubbling and melting phenomena provide a possible direction of study. Copyright © 2007 John Wiley & Sons, Ltd.     

基于ADμC834芯片热泵热水机组控制器的研制

热泵热水机组是一种新型热水和供暖产品,它可以从空气、水等环境中吸取能量,热效率高,被公为是传统锅炉、电热水器及燃油(气)热水机组的更新换代环保型产品。详细阐述了以ADμC834芯片为核心的热泵热水机组控制器软硬件系统设计。论述了多路温度数据与压力数据采集、液晶显示等模块的硬件组成及各个模块的工作原理。控制器的软件系统采用前后台架构,用QuickStart平台开发完成。其人机界面系统由按键阵列和TG2401286V2型液晶显示屏组成。     

联合循环余热锅炉螺旋鳍片管烟气放热系数研究

东南大学建造了1座IGCC余热锅炉鳍片管受热面流动和传热热态试验装置,并先后在其上进行了2个不同螺旋鳍片管组的传热特性研究,通过分析比较实测的烟气侧对流放热系数与无量纲准则式计算的结果,得出了完全热模拟公式更为准确的结论。     

Effect of Hydrogen Heat Treatment on the Chemical Composition of Aluminum Nitride Powder

The effect of hydrogen heat treatment on impurity contents in aluminum nitride powder of different fineness is studied. Thermodynamic calculations are provided pointing to the possibility of forming gaseous hydrogen compounds with impurity elements. It is established that as a result of treatment the contents of impurity elements, i.e. oxygen, carbon, sulfur, are reduced by a factor of 3-13. The optimum hydrogen heat treatment regime is determined: a temperature of 1323 K and an exposure time of 30 min.     

地方热电联产企业发展对策的探讨

介绍了泰州热电企业的运行情况，分析了各热电厂在技术改造、扩大热用户和强化内部考核管理方面的措施，探讨了地方热电企业应采取的对策和发展思路。