An effect of side chain length on the solution structure of poly(9,9-dialkylfluorene)s in toluene

The effect of side chain length of π-conjugated poly(9,9-dialkylfluorene)s has been studied in semi-dilute (10 mg/mL) toluene solutions using small-angle neutron scattering (SANS) and ¹H and ²H NMR spectroscopies. Under these conditions, SANS data indicate that poly(9,9-dinonylfluorene) and poly(9,9-dioctylfluorene) are dissolved down to the molecule level and appear as elongated one-dimensional chains (length >20-30 nm). In contrast, the shorter side chain polymers exhibit a self-association so that poly(9,9-diheptylfluorene) forms thin sheet-like (∼1 nm) and poly(9,9-dihexylfluorene) thin (∼1 nm) and thick sheet-like (>6 nm) aggregates. ¹H NMR data, together with the density functional theory (DFT) calculations, however, show that this occurs without changes in the conformation of the polymer backbone.     

F2.4微孔膜的制备及在膜蒸馏过程中应用的初步研究

采用相转化法制备了F2 4的疏水微孔膜 ,并对F2 4和PVDF微孔膜的机械性能以及疏水性等方面进行了对比 .结果表明 ,F2 4微孔膜在拉伸时的应变以及断裂伸长率约为PVDF微孔膜的 6～ 9倍 ;其接触角 (77 4°)也大于PVDF膜的接触角 (6 6 7°) .尽管膜蒸馏的数据显示F2 4微孔膜的蒸馏通量尚不及PVDF膜 ,但通过调节各项制膜参数 ,F2 4可能具有良好的应用前景     

Emission Of Volatile And Semivolatile Organic Compounds From Waterborne Paints – The Effect Of The Film Thickness

A waterborne paint was applied to tin plated steel sheets with three different film thicknesses. The emission of volatile and semivolaile organic compounds ((S) VOCs) from the samples was measured in small climatic chambers under standard conditions over a two-week period. The purpose of the study was to evaluate the effect of the film thickness on the emission rate decay. First order decay models, including sink effects for the high boiling (S) VOCs, were fitted to the concentration versus time data. The results showed that the first order rate constants decrease with increasing film thickness. In uddition, the results indicated that the emissions of the (S)VOCs in the waterborne paint film seemed to be controlled by evaporation. The thicknesses of paint films used in climatic chamber tests to estimate emission rates for product compurison or emission prediction must be known in order to prevent erroneous conclusions     

A study of the static and dynamic properties of side-chain liquid crystalline polymers in low molar mass mesogens

The static and dynamic properties of solutions of a side chain polysiloxane liquid crystal polymer have been studied in a cyanobiphenyl nematic host as a function of concentration and temperature. Refractive index measurements were carried out on aligned samples and the data used to determine the macroscopic order parameter, S, using Haller's method. Photon correlation spectroscopy has been used to measure ($\text{k}{}_{22}\text{γ}{}_1$) for the pure nematic solvent and the solutions. From these measurements it appears that the static properties vary slowly and linearly with increasing polymer concentration whilst the dynamic or viscoelastic properties change markedly. This change has been attributed to γ₁, the twist viscosity, and the results have been discussed in terms of the function of the siloxane polymer backbone.     

Carbon fibre composites based on polyimide/silica ceramers: aspects of structure-properties relationship

Polyimide/silica ceramers, based on the products of the hydrolysis of tetraethoxysilane (TEOS) and a commercial poly(amic acid) solution, were used to fabricate unidirectional carbon fibre composites, which were subsequently evaluated with respect to thermal and mechanical properties. There is evidence to suggest that the silica component of these ceramers is present as dispersed discrete particles at low silica concentration (i.e. 7 wt%) and as fine interconnected domains trapped within the polyimide matrix at higher silica content (i.e. 14 wt%). The dimensions of the silica domains were in the region of 7–20 nm. Carbon fibre composites produced from ceramer solutions (CF/ceramers) were found to exhibit lower thermal expansion and a greater retention of flexural and interlaminar shear properties at elevated temperature than the corresponding polyimide-matrix composites (CF/polyimide). The properties of CF/ceramers were generally better for systems containing the higher amount of silica and were improved further by lowering the pH value of the precursor ceramer solution. This is believed to have resulted from the enhanced fluidity of the ceramer gel within the pre-impregnated fibres, giving rise to a higher packing density of the fibres and a more homogeneous distribution of fibres. CF/ceramers were also found to exhibit a better thermal oxidative stability at 350°C than the corresponding CF/polyimide, although a substantial amount of porosity developed in the case of ceramers with the higher silica content.     

Fenton试剂处理苯酚和甲醛废水的研究

用H2O2同Fe^2 结合的Fenton试剂处理有机废水是一种经典的催化氧化法，这种方法适合于处理废水中高浓度、难降解的有机物质。主要研究了Fenton试剂处理含苯酚和甲醛有机废水样的反应机理和影响因素，试验结果表明：废水中苯酚和甲醛的去除率均可达到95％以上，COD去除率达到85％以上，表明用Fenton法处理含苯酚和甲醛的有机废水是一种非常有效的方法。     

Surface Areas of Nitrated Hydrotalcites

Hydrotalcites in the nitrate form were prepared using microwave irradiation in the hydrotreatment step. The surface area (BET) of nitrated hydrotalcites was evaluated. Solids were characterized by atomic absorption, X-ray diffraction and BET analysis. Thermal pretreatment temperature determined the surface area of the hydrotalcites.     

Degree of crosslinking and mechanical properties of crosslinked poly(vinyl alcohol) beads for use in solid-phase organic synthesis

The limited swellability in polar media of the commonly used polystyrene/divinylbenzene (PS-DVB) support materials for solid-phase organic synthesis has led to the development of novel, highly swellable hydrophilic gels designed for use in aqueous or polar media. Poly(vinyl alcohol) beads crosslinked with epichlorohydrin (PVA-EP) were prepared by a two-step inverse-suspension polymerization method. While it is known that the morphology of the resulting beads can be controlled by the ratio of EP versus PVA as well as by the pre-crosslinking time, the actual degree of crosslinking of the beads and their mechanical properties remain unknown. It is therefore the purpose of this study to evaluate the actual degree of crosslinking of beads prepared with different quantities of crosslinker in the feed by spectroscopic (Raman, nuclear magnetic resonance) and chemical (functional group loading) methods. The mechanical properties of these swollen PVA-EP beads will be evaluated by single-bead unconfined compression in solvents such as water, N,N-dimethylformamide (DMF), and tetrahydrofuran (THF) and compared to model PS-DVB beads commonly used for solid phase synthesis.     

Biomimetic Polymer Nanostructures by Injection Molding

The nanometer scale topography of self‐assembling structural protein complexes in animals is believed to induce favorable cell responses. An important example of such nanostructured biological complexes is fibrillar collagen that possesses a cross‐striation structure with a periodicity of 69 nm and a peak‐to‐valley distance of 4–6 nm. Bovine collagen type I was assembled into fibrillar structures in vitro and sedimented onto solid supports. Their structural motif was transferred into a nickel replica by physical vapor deposition of a small‐grained metal layer followed by galvanic plating. The resulting inverted nickel structure was found to faithfully present most of the micrometer and nanometer scale topography of the biological original. This nickel replica was used as a die for the injection molding of a range of different thermoplastic polymers. Total injection molding cycle times were in the range of 30–45 seconds. One of the polymer materials investigated, polyethylene, displayed poor replication of the biological nanotopographical motif. However, the majority of the polymers showed very high replication fidelity as witnessed by their ability to replicate the cross‐striation features of less than 5 nm height difference. The latter group of materials includes poly(propylene), poly(methyl methacrylate), poly(L ‐lactic acid), polycaprolactone, and a copolymer of cyclic and linear olefins (COC). This work suggests that the current limiting factor for the injection molding of nanometer scale topography in thermoplastic polymers lies with the grain size of the initial metal coating of the mold rather than the polymers themselves.