Passivation effects of deuterium exposure on boron-doped CVD homoepitaxial diamond

The deuterium (hydrogen) passivation effect on acceptors in boron-doped CVD homoepitaxial diamond was studied by electrical (Hall-effect) and secondary ion mass spectroscopy (SIMS) measurements. Deuterium was incorporated into the samples using microwave (MW) deuterium plasma at 673 K for 2–24 h. We observed the progress of acceptor passivation with p-type conduction, which finally resulted in a highly resistive state.     

Electrical/electronic effects of titanium and iron impurities in EFG and FZ solar cell silicon: SPV/EBIC analysis

In this paper results on surface photovoltage (SPV) and electron beam induced conductivity (EBIC) studies of edge-defined film-fed growth (EFG) and floating zone (FZ) silicon solar cell materials (both p-type) are presented. A systematic comparison based on minority carrier diffusion length and carrier recombination is made between: (i) samples contaminated with Ti and/or Fe, (ii) samples gettered by phosphorous diffusion, and (iii) as-received samples. Deep level transient spectroscopy (DLTS) measurements, together with the iron-boron (FeB) pairing kinetics [1] have successfully been used to detect the presence of Fe in the samples. Even though this process is effective in revealing Fe impurities in p-type FZ silicon it is evidently not suitable for Fe identification in p-type EFG silicon. Ti, like Fe, is found to be a prominent lifetime-limiting metallic impurity in both EFG and FZ silicon. Phosphorous diffusion is proven to be an effective external gettering technique for fast-diffusing impurities such as Fe, but not for Ti.     

A comparative thermodynamic study of sorption systems: second law analysis

As a consequence of the phasing out of CFCs, sorption systems appear to be potential candidates to replace vapour compression systems. Amongst sorption systems there exists a choice between several systems, such as liquid absorption, solid adsorption and chemical reaction heat pumps. Nevertheless, few comparative studies between these systems have been undertaken so far. It is the aim of this paper to present such a study based on combined first and second law thermodynamical analysis of the different cycles. Simple entropy generation processes explain why the basic cycles for these systems yield performances much lower than the Carnot efficiency. The possibility of operating regenerative cycles with internal heat recovery and higher efficiencies has also been considered for typical common base conditions. Different entropy generation considerations have been visualised, such as thermal coupling (external/internal), non-uniform temperature component entropy production and other irreversible processes for the COP degradation in these systems. It is found that thermal coupling irreversibilities in solid sorption systems and other internal irreversibilities in liquid sorption systems with solution heat exchanger are dominant in the actual COP degradation with respect to the reversible Carnot COP.     

WC对Cu/WC_P复合材料性能及组织的影响

通过ＷＣ含量对ＷＣ／Ｃｕ复合材料性能的影响，确定了冷压－烧结法制备Ｃｕ／ＷＣ材料的适宜ＷＣ含量为１０ｖｏｌ％左右。并就ＷＣ对该材料组织和再结晶行为的影响进行了有益的探讨。     

地震数据采集系统中频谱均衡滤波器的理论设计

地层的高频吸收衰减效应是导致地震勘探分辨率不高的主要原因，在高分辨率野外地震数据系统中，频谱均衡滤波器所设置的重要部件。文章以频谱均衡滤波器的原理和地层吸收衰减特性为基础，用计算机模拟的方法研究地层吸收衰减使分辨率降低的程度和频谱均衡滤波器对分辨率的补偿效果，给出了较好的频谱均衡滤波器的设计方案。     

Preparation of polyimide-epoxy composites

The formation of a three dimensional network of crosslinked epoxy leads all unmodified epoxies to have inherent brittleness and relatively low degradation temperatures. Polyimides, on the other hand, are widely used for applications that require high degrees of flexibility and thermal resistance. Here, we have focused on the preparation of epoxy systems cured with polyamic acids instead of traditional amino-group-containing hardening agents. The cure behavior and potential reaction mechanisms of EPON 828 resin and polyamic acid mixtures were evaluated by DSC and TGA. Thermal analysis showed a complex reaction sequence taking place in the mixture and also determined the extent of reaction of the polyamic acid with itself and the competitive reaction of the polyamic acid with the epoxy. The compositions of the mixtures were varied to see the dependence of the cure behavior on component concentrations. Solutions of the two components did not phase separate and also phase separation was not apparent either optically or microscopically in the cured samples. This phase behavior was attributed to a unique in situ reaction. A novel solvent system for the polyamic acid precursor was also used.     

反应堆材料热物性数据库管理系统

衡量一个数据库的质量，不以要看其所包含的数据还应考虑数据库管理系统的使用功能。为了更有效地实施ＩＡＥＡ的ＣＲＰ（ＣｏｏｒｄｉｎａｔｅｄＲｅｓｅａｒｃｈＰｒｏｇｒａｍｍｅ）中有关建立反应堆材料热物性数据库的计划，并考虑到能使所收集的数据方便地为用户服务和进行广泛的国际交流，为此设计并编制了该数据库的软件管理系统ＴＰＳＹＳ。这个系统可在ＩＢＭ－ＰＣ（３８６，４８６）等兼容机上运行，采用人机对话、菜单提示、全屏幕操作。其主要功能有：数据库维护、数据检索、与大型计算程序ＭＡＴ－ＰＲＯ接口和与国际上现有的数据库ＴＨＥＲＳＹＳＴ接口。     

Mechanical degradation of coating systems in high temperature cyclic oxidation

Cyclic oxidation tests were performed on a large variety of commercially available overlay coatings. The results of cyclic oxidation tests confirmed that the composition of the coating as well as the processing method of the coating can affect the life of the system. Coating life was determined by the time to coating penetration and initiation of substrate attack. As this work was part of a effort to evaluate the relative protectiveness of available coating systems for Industrial Gas Turbine applications at relatively high temperature, an extensive testing programme was undertaken. The different coatings were tested to visual failure. The results presented in this paper concentrate on the surface instability of the coating. Apart from usual oxidation of the coating an additional degradation mechanism was observed. A mechanical effect caused by the instability of the coating as a result of the difference in the thermal coefficient of expansion and mechanical properties between the substrate and coating. This effect, the so-called “rumpling” effect, resulted in a significant reduction in time to penetration and was in some systems the life controlling factor.     

Structural properties of inorganic materials: tungsten bronze SBN ceramics

Rare-earth doped strontium barium niobates were synthesized using usual ceramic technique. The dopants are La, Ce, Gd, Sm and Nd. The materials were characterized by XRD and density measurements. The grain sizes were determined from SEM analysis. Lattice parameters changed uniformly with rare-earth dopants in unfilled structures. Density measurements and SEM analysis confirmed only minute changes in the densities of the ceramics.