由乙腈一步法制备乙酸丁酯的研究

以丁醇和制备丙烯腈的副产物乙腈为原料 ,采用一步法合成了乙酸丁酯。通过正交实验得到了影响反应的 4种因素。确定了最佳的工艺条件为 :催化剂的量为样品质量的 40 % ;n(CH3CN)∶ n(C4 H9OH) =1∶ 1 .0 5 ;反应温度为 1 0 5℃ ;反应时间为 8h。在此反应条件下 ,乙酸丁酯的收率为 88.8% ,纯度可达 99.5 %。并用气相色谱及红外光谱对产品的纯度进行了表征     

HP700圆锥破碎机动锥的有限元分析

对HP700圆锥破碎机的主要部件动锥建立了有限元分析模型，用ANSYS软件对动锥进行了有限元强度和刚度分析，结果输出了动锥分布及变形图，对圆锥破碎机的结够设计提供了依据。     

建筑墙体表面传热系数辨识研究

对实验房间南向墙体内表面中心区域的换热过程进行实验，发现当风速在0－5．5m/s之间时，表面传热系数在8－18W（m^2.K）之间波动，而风向对墙体表面传热系数影响不大；用辅助变量法分析墙体表面传热过程，并结合实验推导出墙体表面传热系数。模型的预测结果与实测结果吻合良好。     

燃烧—气体容量法测定冶金石灰中的二氧化碳

冶金石灰是石灰石经过工业煅烧的产品。其二氧化碳含量低，且经过高温煅烧后基本不含有机物。无需按照《石灰石、白云石化学分析国家标准中二氧化碳的化学分析方法》中用酸进行试样分解，只需在1200℃高温中灼烧，使石灰中残留的或煅烧后吸收空气中二氧化碳而形成的碳酸盐分解，象通常测定含碳耐火材料中二氧化碳那样，采用气体容量法进行测定。     

A continuum-based modeling of MEMS devices for estimating their resonant frequencies

A continuum-based modeling of coupled electrostatics-structure interactions is presented for the frequency computations of MEMS devices. The present general formulation of electrostatics accounting for free space is validated first by specializing it to one-dimensional uniform motion of conducting surfaces and comparing the resulting electrostatics to conventional lumped models. The general coupled electrostatics-structure interactions are then applied for the prediction of resonant frequencies of MEMS devices due to bias-voltage changes and temperature variations. Comparisons of predicted resonant frequencies obtained by the present coupled electrostatics-structure interaction models with experimental results available in the literature demonstrate that the proposed continuum-based interaction modeling yields high-confidence predictions of resonant frequencies of MEMS devices.     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

Cholesterol‐imprinted polymer receptor prepared by a hybrid imprinting method

A novel cholesterol‐imprinted polymer (CMIP‐H) was prepared by a hybrid method of covalent imprinting and non‐covalent imprinting. This approach involves the copolymerization of a template‐containing monomer, cholesteryl 2‐hydroxyethyl methacrylate carbonate, and a cross‐linker, followed by hydrolysis to afford a flexible guest‐binding site accompanied with the easy and efficient removal of a ‘sacrificial spacer’. The effect of solvent on the binding capacity of CMIP‐H towards cholesterol was studied, indicating that a good binding capacity towards cholesterol could be achieved in a less‐polar solvent. The binding experiments of CMIP‐H towards a series of structural analogues of cholesterol, including cholesterol acetate, progesterone and stigmasterol, were carried out in hexane. The results showed that CMIP‐H almost did not bind cholesterol acetate at all because the hydrogen‐bonding site is blocked. It exhibited a similar binding towards both cholesterol and stigmasterol, but much higher binding towards progesterone. Copyright © 2005 Society of Chemical Industry     

A comparative study of numerical solutions to non-linear discrete crack modelling of concrete beams involving sharp snap-back

Numerical problems are often encountered in modelling crack propagation in concrete beams using non-linear finite element (FE) analysis, especially when sharp snap-back behaviour in load-displacement relations occurs. This paper firstly identifies 16 arc-length control based numerical strategies based on extensive literature review. They are then used to carefully model the structural behaviour of a four-point single notched shear beam using discrete crack modelling approach in which cracks are represented by interface elements with bilinear softening constitutive laws. Based on extensive FE analyses, detailed comparisons of the merits and demerits of these numerical algorithms are then made. The results indicate that the effectiveness and efficiency of different algorithms may vary considerably from one to another, with the local arc-length based procedures in conjunction with tangential stiffness strategy and reversible unloading model being the most robust.     

真空制盐蒸发结晶器的设计与实践

真空蒸发制盐外热式强制逆循环轴向出料蒸发结晶器，经多个厂家生产应用实践证明是成功的，具有生命力的。这种新型结构，作为一项新技术新设备应加强研究，总结提高，推广应用。不断完善。文章从流体力学、结晶机理角度要求，到具体工程设计参数和材质选用。论述了该罐的特点。     

熔融碳酸盐燃料电池阴极材料的导电性

通过交流阻抗方法研究了熔融碳酸盐燃料电池阴极材料锂镍氧化物、锂钴氧化物和锂铁氧化物的导电性能。结果表明:锂镍氧化物电极的导电性最好,锂钴氧化物电极的导电性次之,锂铁氧化物电极的导电性最差;它们的导电性都随着温度的升高而按指数规律增加;在合成锂钴氧化物(或锂铁氧化物)的过程中,使Li2CO3轻微过量,可以提高锂钴氧化物(或锂铁氧化物)电极的导电性,而且在同一温度下,随着nLi∶nCo(或nLi∶nFe,摩尔比)值的增大,锂钴氧化物(或锂铁氧化物)电极的导电性显著增加。