形变与热处理对Cu-Cr合金力学性能的影响

研究了不同形变与热处理工艺对多元Cu-Cr合金的力学性能的影响.结果表明该合金有显著的时效强化特性,强化相为Cr,当合金经65%变形再经500℃×4 h时效处理可获得较高的硬度;变形能降低合金的冲击韧度,而时效处理对合金的冲击韧度影响不大.     

大学生教育管理应以理性个性培养为导向

个性包括品德、品格、爱好、自我修养等,能够反映一个人的整个精神面貌。个性并非是与生俱来的,也并非完美无缺,有的还可能存在较大的缺陷。理性个性是个性的升华,是自由、全面、和谐和自律的个性,是一种理想,一种追求,是个性发展的最高境界。目前,高校在培养大学生理性个性的过程中还存在一定问题和矛盾。大学生教育管理应该在主导者的积极指导下,让学生来对自己的个性发展负责,培养理性个性,让他们懂得怎样去理解别人,同别人相处,懂得自己所肩负的责任。     

高强度钢焊接裂纹检测及其成因分析

为了充分认识高屈强比、高强度低温材料焊接裂纹的敏感性，通过对NK—HIT—EN610U2L低合金高强度钢球罐支柱角焊缝裂纹的检测、解剖对比和成因分析，发现焊缝外表面缺陷与内部焊接缺陷存在一定关系，高应力设计部位比较突出，因此检测与焊接要引起高度注意。     

快速凝固Mg94.6Zn4.8Y0.6镁合金薄带的组织与性能

采用单辊快速凝固技术制备了Mg94.6Zn4.8Y0.6合金薄带,研究了薄带的组织及性能特征。结果表明:Mg94.6Zn4.8Y0.6镁合金快速凝固薄带组织由过饱和的单相-αMg固溶体组成,沿厚度方向分为两个晶区:近辊面粗大等轴晶区和自由面细小等轴晶区。Mg94.6Zn4.8Y0.6合金快速凝固薄带的显微硬度为85.95HV,在250℃左右保温2 h的显微硬度最高,超过该温度(250~300℃)显微硬度显著下降。     

High-Temperature Corrosion Resistance of Al–Re and Re Coatings

The oxidation behavior in air at 1473 K, and sulfidation behavior in a H2S–H2 gas mixture with a sulfur partial pressure of 10^–2 Pa at 973 K of Al–Re coated CMSX-4 were studied. Investigation on the sulfidation behavior of the Re-coated CMSX-4 was carried out in a H2S–H2 gas mixture with a sulfur partial pressure of 10^–2 Pa at 973 K. The experimental results show that a Re-rich alloy layer was formed between an -Al₂O₃ layer and the inner concentration zone of Ta and Ti for the CMSX-4 single crystal alloy with an Al–Re coating after oxidation. The Re-rich alloy layer containing Cr, W, Ni, Co, and Mo effectively inhibited the outward diffusion of alloying elements and the inward diffusion of Al. The Al/Re-coated CMSX-4 single crystal alloy had excellent sulfidation resistance; the Re-rich alloy layer, containing W, Ti, Ta, and Mo, which formed during the sulfidation process and located between the alumina scale and the CMSX-4 base alloy, plays a role in inhibiting the outward diffusion of alloying elements. The sulfidation resistance of CMSX-4 single-crystal alloy is greatly improved by a Re coating on the CMSX-4 alloy surface; this is attributed to a Re–Cr–W alloy layer that retarded the outward diffusion of cations and the oxide layer containing Ta, Ti, and Al, which inhibited the inward penetration of sulfur.     

我国中厚钢板近期发展探讨

本文介绍了国内外中厚板轧机的发展简况并根据本世纪末中厚钢板的市场需求预测,对我国中厚板轧机的发展提出探讨。     

矿山磨光球用钢XK5159H的生产试制

XK5159H钢连铸连轧棒材用于制造矿山磨光球，对于钢的纯净度、低倍组织、探伤结果及DI值等均有严格的要求，很难控制。我们通过制定内控化学成分及合理的工艺路线，使生产试制一次成功。     

碳纳米管及稀土元素钇(Y)对高Ni含量Ti(C,N)基金属陶瓷组织与性能的影响

研究了不同含量的碳纳米管及0.8%稀土Y对高Ni含量Ti(C,N)基金属陶瓷组织性能的影响.将不同成分的试样分别于1400℃、1410 ℃、1420℃真空烧结,测试抗弯强度、洛氏硬度,观察背散射电子形貌、断口形貌并做能谱分析.结果表明,加入质量分数(下同)为0.8%Y及0.3%～1.0%的碳纳米管时,碳纳米管含量为0.5%的组织较均匀,芯壳结构明显,抗弯强度及硬度均较高.     

High-temperature corrosion and creep of Ni-Cr-Fe alloys in carburizing and oxidizing environments

The carburization of NiCr 32 20 and NiCrSi 60 16 has been studied in CH₄-H₂ mixtures in the temperature range 900–1100°C. The methods included thermogravimetric measurements and studies on reacted specimens by X-ray diffraction, metallographic, and chemical analysis. Upon carburization internal carbides M₇C₃ and M₂₃C₆ are formed (M=mainly Cr); the rate of carburization is determined by carbon diffusion in the Fe-Ni matrix with carbide precipitations. The effect of the alloying elements Ni and Si on the carburization resistance of austenitic alloys is explained. By the same methods the oxidation and carburization in CO-H₂O-H₂ mixtures have been studied. The important role of a stable chromium oxide layer for the carburization resistance was confirmed. Creep tests at 1000°C in a CO-H₂O-H₂ atmosphere where Cr₂O₃ is stable showed carburization occurring through cracks in the oxide layer. At high strain rates premature failure occurs by carburization, which is followed by internal oxidation and formation of cracks, voids, and holes.     

TiAl 合金中的γ→α析出转变行为

研究了Ti-48Al和Ti-48Al—0．8B合金中的γ→α析出转变，分析了α析出相的生长形态、晶体学特征、生长动力学及α／γ相界面结构。结果显示α相从γ相中析出有两种方式：一种是从γ晶粒内沿{111}，晶面以片状形貌析出，且α相与γ基体保持共格位向关系；另一种则是在γ晶界上通过不连续析出转变，以不规则的块状形貌析出，并向着晶界一侧与之无位向关系的γ晶粒内生长。添加0．8％(摩尔分数)B能显著降低γ晶粒内片状α析出相的形核率，并抑制α相生长。HREM分析表明：片状α相是在γ相的堆垛层错上形核，并通过“台阶-凸起-扭折”机制生长；α／γ相界面上复杂层错的存在及台阶形核率低是片状α相沿厚度方向生长缓慢的主要原因。