A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

核电材料在模拟反应堆环境中应力腐蚀破裂测试技术与性能评价

简要介绍了采用慢应变速率试验，Ｕ型弯曲和Ｃ形环试验等技术，分别对８００合金，３０４和３１６及３１６Ｔｉ不锈钢Ａ５３３Ｂ压力容器用多在模拟核反应堆环境中的应力腐蚀破裂敏感性性进行的试验研究的一些主要结果；并结合电化学测试和表面膜俄歇电子能谱分析结果进行了讨论。     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

NADRA 3D information technology for analysis of processes in multicomponent soil media

This paper considers the principles of algorithmic and software implementation of the software system NADRA 3D designed to analyze processes in three-dimensional multicomponent soil media. The principles of operation of NADRA 3D are described. __________ Translated from Kibernetika i Sistemnyi Analiz, No. 6, pp. 157–174, November–December 2006.     

晋城市煤炭加工利用现状、存在问题及发展建议

阐述了晋城市煤加工利用的现状 ,分析了煤炭加工利用存在的问题 ,提出了今后的发展建议     

鄱阳湖控制浅说

该控制工程主要效益是改变鄱阳湖“夏水冬陆”的现状，成为祖国名符其实的第一大淡水湖，水面与避署胜地庐山和历史名城南昌、景德镇等相连，改善沿湖环境，发展航运，增加水产，开发利用丰富的水资源和旅游资源使之与杭州西湖、瑞士日内瓦湖等并列为世界名湖。     

换热器小浮头螺栓断裂失效分析

针对换热器小浮头螺栓发生断裂的情况进行失效分析，找出原因，提出处理措施及材质选择时应注意的问题。     

CMF300M355NU型质量流量计在油库汽车装车中的应用

介绍了质量流量计的工作原理有应用效果。这种新型质量流量计精度高，稳定性好，示值计量简便，可直接显示质量、流量、介质温度、密度等，维护量低，但必须正确安装、使用，才能发挥其应有的作用。     

秸杆材料用作草皮栽培基质的研究

本文介绍了秸杆毡的成型工艺 ,通过植物所需的水、肥料和空气三种因素对秸杆毡的化学和物理性能进行了研究 ,该材料可被用作草皮栽培基质     

局部设有钢筋砼电梯井墙的设计探讨

本文就局部设有钢筋砼电梯井的工程计算及理论分析，阐明分析了少墙的框剪结构的设计及注意问题。