Determination of the Coordinates of the Center of a Gaussian Beam by Means of a Matrix Photodetector Using a Weighting Method

A weighting algorithm to determine the coordinates of the center of a Gaussian laser beam projected onto a matrix photodetector is considered. The influence of the internal noise of the photodetector, the maximum brightness of the signal at the beam maximum, and the beam radius on the precision of the algorithm is investigated. Recommendations on image processing are presented.     

Electron transport in InGaO3(ZnO)m (m=integer) studied using single-crystalline thin films and transparent MISFETs

We have investigated the characteristics of transparent metal-insulator-semiconductor field-effect transistors (MISFETs) fabricated using InGaO₃(ZnO)_m (m=integer) single-crystalline thin films as n-channel layers and amorphous alumina as gate insulator films. The MISFETs exhibit good characteristics such as insensitivity to visible light illumination, off-current as low as ∼1 nA with a positive threshold voltage of ∼3 V and on/off current ratio of 10⁵. The field-effect mobility increased from ∼1 to ∼10 cm² (V s)⁻¹ as the m-value increased. Room temperature Hall mobility also increased. However, unexpectedly these values were lower than the field-effect mobility. It is explained by existence of shallow localized state in the homologous compounds.     

25mm厚钢板产生层间撕裂的原因和防治

层间撕裂并非是厚板独有的质量问题 ,结合工程实例 ,分析 2 5mm厚低合金钢板产生层间撕裂的原因。通过对钢材的超声波探伤检测、化学成分分析和Z向性能检测 ,指出层间撕裂主要与节点设计不当和钢材内非金属夹杂物偏析、分层有关 ,并提出了预防措施。对产生裂纹的构件视严重情况提出了不同的修补处理方法     

A low cost calibration conditioner for dynamic strain gauge measurements

A conditioner for dynamic strain measurements that allows for a series of calibration signals with periodic and predefined time occurrence, during the whole period in which the measurements have to be carried out, is presented in this work. The calibration signals, having suitable size ratios between them, allow one to evaluate the linearity of the entire measurement chain.     

Degradation of NiCr/CuNiMn/NiCr films on alumina substrates

This paper addresses the aging behaviour of NiCr/CuNiMn/NiCr triple layers on Al₂O₃ ceramics at temperatures up to 200°C for film thicknesses d0.5 μm. Investigations of the film structure and the increase of resistance and its temperature coefficient during the annealing process and studies of the dependence of this aging drift on both the film thickness and the storage temperature have been carried out. Furthermore, the film stress and the effect of substrate bending on resistance have been measured. The results can be explained by the irregular film structure (columns and small bridges between them), which causes stress and current concentrations as well as local creeping, cracking and oxidation processes in the micro-bridges. They are compared with such for structurally homogeneous films on silicon wafers.     

Improvement of the methods of reproducing and transferring the dimensions of the unit of sound pressure in an aqueous medium under free-field conditions

Methods of reducing the predominant components of uncertainty in standards of sound pressure in an aqueous medium in a free field, and also methods of increasing the accuracy when the dimensions of the unit of a physical quantity are transferred by the means employed in natural measurements are reviewed. __________ Translated from Izmeritel’naya Tekhnika, No. 8, pp. 59–63, August, 2007.     

The initial behaviour of freshly etched copper in moderately acid, aerated chloride solutions

When freshly etched samples of various types of copper were exposed in moderately acid, aerated chloride solutions, two phenomena were observed. First the corrosion potential and the pH of the solution decreased over a shorter time, then the potential increased over a long period (600-1500 min), following an s-shaped pattern. Increase in pH during the second stage was avoided using a pH-stat. The corrosion rate increased little or not at all over the entire period. A tentative interpretation of the short-term behaviour is presented with some reservation. The long-term development of the potential suggests phase formation or transformation following the Avrami pattern. By suitable derivations it was possible to fit the development of potentials to the Avrami equation. Subsequent examinations by Auger spectroscopy proved the presence of thin layers of Cu₂O on the copper surfaces, increasing in thickness with exposure time. The dissolution kinetics can be described in terms of two parallel electrochemical reactions and a simultaneous non-electrochemical dissolution reaction.     

A new ‘tailor-made’ methodology for the mechanical behaviour analysis of rubber-like materials: I. Kinematics measurements using a digital speckle extensometry

This paper is the first part of a work devoted to the setting-up of a methodology for the mechanical behaviour characterization of rubber-like materials, using a digital speckle extensometer. We present here the experimental approach, specific to large strain measurements. The proposed method is based on in-plane kinematics measurements using an optical extensometer. The whole two-dimensional field of in-plane displacements is obtained by a digital image processing. We discuss then the correlation calculations and how to achieve the optimal subset matching. Next, we specify how to derive the principal stretch ratios, and the accuracy on these components, issued from a subsequent numerical calibration.Finally, we present experimental data dealing with a carbon black, filled natural rubber, issued from uniaxial traction tests, pure shear tests, and tensile tests performed on double-edge notched tensile specimens.     

Spatiotemporal aspects of jerky flow in Al–Mg alloys, in relation with the Mg content

The spatiotemporal aspects of the Portevin–Le Chatelier effect in Al–Mg alloys are investigated using direct observations of the sample surface with a digital camera. Optical measurements of the surface profile using a white light interferometer allow the estimation of the local strain and strain rate associated with the bands. The effect of Mg content on instability characteristics is analyzed. The reloading time is shown to depend on the Mg content only at the strain and strain rates where type C bands are observed.     

Mesomorphism of Lanthanide(Ⅲ) 4-Hexyloxybenzoates

The 4-alkoxybenzoic acids are well-known liquid crystals showing several mesophases(nematic,smectic C phase or both)depending on the alkoxy chain length and whereby the rigid core of the mesogen is formed by intermolecular hydrogen bonds.In this paper it is shown that the thermal behaviour of lanthanide salts of 4-hexyloxybenzoic acids depends on the lanthanide ion(Ln=La,Pr,Nd,Sm,Eu).The lanthanum(Ⅲ)and praseodymium(Ⅲ)4-hexyloxybenzoates exhibit a smectic A mesophase.No mesophase is found for the corresponding compounds of heavier lanthanides.The thermal properties of the lanthanide(Ⅲ)4-hexyloxybenzoates were investigated by differential scanning calorimetry(DSC),polarising thermo-optical microscopy and synchrotron X-ray radiation.