碱性燃料电池用阴离子交换膜的研究进展

阴离子交换膜燃料电池（AEMFCs）因其具有环境友好、可使用非贵金属催化剂、电极反应速率快等特点而受到广泛关注。阴离子交换膜（AEMs）是AEMFCs的核心部件,其性质决定着燃料电池的性能、能量效率和使用寿命。从具有不同骨架结构的聚合物出发,介绍了聚苯醚、聚芳醚砜、聚烯烃和聚苯并咪唑等不同聚合物骨架结构的阴离子交换膜的制备、性能和应用,同时对具有不同聚合物骨架结构的阴离子交换膜在应用方面存在的问题及应用前景进行了评论和展望。     

Electrochemical and microstructural characterization of cyclic redox behaviour of SOFC anodes

The oxidation of Ni to NiO in solid oxide fuel cell (SOFC) anode will result in large bulk volume change, which may change the interfaces of the two phases in the anode cermet and thus may cause significant performance degradation. The reduction and oxidation (redox) of the Ni/YSZ cermet were studied at 800 ℃. Anodic polarization measurements were performed before and after redox cycles. The anode current density at an overpotential of 100 mV kept decreasing during the whole redox treatment. It decreased from 19.11 to 7.95 mA·cm-2 after two redox cycles. Anode supported unit cell was assembled for cell's discharge measurements. Cell performance declined after each redox cycle. The maximum power density decreased from 126.28 to 40.32 mW·cm-2 . The microstructural changes after redox cycling were recorded using scanning electron microscopy (SEM). The results reveal that after re-oxidation, the Ni gets coarse and has a higher porosity; the nickel network structure turns to be desultory.     

Characterization of YSZ solid oxide fuel cells electrolyte deposited by atmospheric plasma spraying and low pressure plasma spraying

Yttria doped zirconia has been widely used as electrolyte materials for solid oxide fuel cells (SOFC). Plasma spraying is a cost-effective process to deposit YSZ electrolyte. In this study, the 8 mol% Y₂O₃ stabilized ZrO₂ (YSZ) layer was deposited by low pressure plasma spraying (LPPS) and atmospheric plasma spraying (APS) with fused-crushed and agglomerated powders to examine the effect of spray method and particle size on the electrical conductivity and gas permeability of YSZ coating. The microstructure of YSZ coating was characterized by scanning electron microscopy and x-ray diffraction analysis. The results showed that the gas permeability was significantly influenced by powder structure. The gas permeability of YSZ coating deposited by fused-crushed powder is one order lower in magnitude than that by agglomerated powder. Moreover, the gas permeability of YSZ deposited by LPPS is lower than that of APS YSZ. The electrical conductivity of the deposits through thickness direction was measured by potentiostat/galvanostat based on three-electrode assembly approach. The electrical conductivity of YSZ coating deposited by low pressure plasma spraying with fused-crushed powder of small particle size was 0.043 S cm⁻¹ at 100 °C, which is about 20% higher than that of atmospheric plasma spraying YSZ with the same powder. This article was originally published inBuilding on 100 Years of Success, Proceedings of the 2006 International Thermal Spray Conference (Seattle, WA), May 15–18, 2006, B.R. Marple, M.M. Hyland, Y.-Ch. Lau, R.S. Lima, and J. Voyer, Ed., ASM International, Materials Park, OH, 2006.     

Preparation and characterization of TiO2 photoelectrode codoped with aluminum and boron and its application in dye-sensitized solar cell

Nanocrystalline titania films codoped with aluminum and boron were prepared by cathodic vacuum arc deposition. In the process, titanium alloy target was used under an O2/Ar atmosphere, and sensitization of films were carried out by natural dye-sensitized complex in anhydrous ethanol. The structure, surface morphology and UV-vis spectra of titania films codoped were measured by X-ray diffraction analysis, scanning electron microscopy and ultraviolet-visible spectrometer. Theas-deposited films are found to be amorphous. The films annealed were examinedto be of anatase structure with orientation along the (101) planes, the averagecrystal size is in the range between 41 and 45 nm. SEM results show that thereare some pores in the codoped titania films, the optical properties of the dye-sensitized films were also measured which reveals that the spectral responses of films shift to the visible region. Under simulated sunlight illumination, the overall energy conversion efficiency of dye-sensitized nanocrystalline solar cell is 0.9%.     

Synthesis and characterization of La0.8Sr0.2MO3−δ (M=Mn, Fe, or Co) cathode materials by induction plasma technology

In this work, nanopowders of perovskite cathode materials (La_0.8Sr_0.2MnO_3−δ, La_0.8Sr_0.2FeO_3−δ, and La_0.8Sr_0.2CoO_3−δ), for use in solid oxide fuel cells (SOFC), were successfully synthesized, using induction plasma techniques. Their compositions, structures, morphology, particle size distributions, and BET specific surface areas were determined for comparison with their counterparts prepared by the Pechini method and by the glycine-nitrate combustion (GNC) technique. The particle sizes of the plasma-synthesized powders are mostly around 63 nm. These plasma-synthesized powders are generally globular, their BET specific surface areas being about 26 m²g⁻¹, approximately twice those of powders prepared by the GNC and Pechini methods. These plasma-synthesized powders are readily reproducible and are not agglomerated. Their individual particle sizes and distributions are very independent of their composition.     

Influence of Plasma Instabilities in Ceramic Suspension Plasma Spraying

Direct current Suspension Plasma Spraying (SPS) allows depositing finely structured coatings. This article presents an analysis of the influence of plasma instabilities on the yttria-stabilized suspension drops fragmentation. A particular attention is paid to the treatment of suspension jet or drops according to the importance of voltage fluctuations (linked to those of the arc root) and depending on the different spray parameters such as the plasma forming gas mixture composition and mass flow rate and the suspension momentum. By observing the suspension drops injection with a fast shutter camera and a laser flash sheet triggered by a defined transient voltage level of the plasma torch, the influence of plasma fluctuations on jet or drops fragmentation is studied through the deviation and dispersion trajectories of droplets within the plasma jet. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

Proteomics of plaques and novel sources of potential biomarkers for atherosclerosis

Cardiovascular disease (CVD) is the leading cause of death and loss of productive life years in the world. The underlying syndrome of CVD, atherosclerosis, is a complex disease process, which involves lipid metabolism, inflammation, innate and adaptive immunity, and many other pathophysiological aspects. Furthermore, CVD is influenced by genetic as well as environmental factors. Early detection of CVD and identification of patients at risk are crucial to reduce the burden of disease and to allow personalized treatment. As established risk factors fail to accurately predict which part of the population is likely to suffer from the disease, novel biomarkers are urgently needed. Proteomics can play a significant role in identifying these biomarkers. In this review, we describe the progress made in proteome profiling of the atherosclerotic plaque and several novel sources of potential biomarkers, including circulating cells and plasma extracellular vesicles. The importance of longitudinal biobanking in biomarker discovery is highlighted and exemplified by several plaque proteins identified in the biobank study Athero-Express. Finally, we discuss the PTMs of proteins that are involved in atherosclerosis, which may become one of the foci in the ongoing quest for biomarkers through proteomics of plaque and other matrices relevant to the progression of atherosclerosis.     

Secretory profile of metapleural gland cells of the leaf-cutting ant Acromyrmex coronatus (Formicidae: Attini)

Ants present a pair of metapleural glands located at the posterolateral end of the thorax. Because of its importance in the social organization of ants, the present study was aimed at describing the morphophysiology of this gland in three worker castes of Acromyrmex coronatus, focused on secretory activity using histological and histochemical techniques. Our findings revealed that the secretory and the storage portions of this gland are connected by extracytoplasmic portion of canaliculi that drain the secretion from each secretory cell to the collecting chamber. This secretion contains glycoproteins. In minor workers, the secretion contains higher levels of polysaccharides when compared to that of major workers, supporting the role of the metapleural gland in the maintenance of the fungus garden. The nucleus as well as cytoplasm of secretory cells were strongly positive for RNA indicating that these cells are active in the synthesis of proteins and lipids, compounds found in the final secretion. The variant of the CEC revealed that the secretory activity of the entire gland is synchronous, as all cells exhibit the result.     

光伏电池最大功率点跟踪方法比较

根据太阳能光伏电池的工程数学模型,在Matlab环境下建立了光伏电池仿真模型,分析了光照强度和温度变化对光伏电池输出特性的影响。针对扰动观察法采用固定的扰动步长而难以获得较高跟踪精度和响应速度的问题,提出了一种基于变步长的改进的扰动观察法,并通过对光伏电池控制系统进行仿真,比较了这2种最大功率点跟踪方法的仿真曲线。结果表明,采用改进的扰动观察法的光伏电池控制系统能更快速跟踪最大功率点,且在最大功率点处稳定性较好。     

基于光伏电池输出特性的MPPT算法研究

为了寻找更好的实现光伏发电系统最大功率点跟踪控制方法,基于单个光伏电池的物理特性建立了太阳能光伏电池阵列的Matlab仿真模型,分析了太阳能光伏电池阵列所具有的随着光照强度和温度不同而变化的P-U和I-U非线性特性.基于光伏电池的动态特性,在最大功率点跟踪算法的设计中增加一个电流监测回路,并结合自寻优技术对电导增量法进行改进,提出了一种自适应变步长寻优算法.仿真结果表明,该算法能够快速准确的跟踪最大功率点.