高Al2O3物料对镍电炉渣粘度的影响

论文对Al2O3高达69．46％的含镍物料电炉处理时对炉渣性能的影响进行了研究。研究表明：吉林镍业公司冶炼厂电炉渣1340℃时黏度为0．538P．s；电炉渣在不添加任何其它试剂的情况下，渣中Al2O3含量不宜高于9％；加入添加剂后，炉渣黏度降低，当在配料中加入20％此种含镍物料时，添加剂加入量7％为宜，此时炉渣黏度为0．74P．s（1340℃）。     

The Synthesis of Sulfated Titanium Oxide Nanotubes

TiO₂ nanotubes can be prepared in gram quantities by treating anatase TiO₂ powder with concentrated NaOH solution. These TiO₂ nanotubes acquired strong acidity after being impregnated with sulfuric acid solution and calcined at 300 °C. The anatase TiO₂ powder used to prepare the nanotube did not catalyze the esterification between cyclohexanol and acetic acid, while sulfated TiO₂ nanotubes were very reactive toward the esterification reaction.     

Growth Stresses in the Oxide Scales on TiAl Alloys at 800 and 900°C

In the oxidation of TiAl alloys, the role of scale-growth stresses formed during oxidation has, thus far, been unknown. In the present paper the oxide-growth stresses were investigated by the deflection-test method in monofacial oxidation (DTMO) accompanied by acoustic-emission measurements. On unmodified surfaces the growth stresses are compressive and reach levels of around –100 MPa. At the same time, significant acoustic emission occurs indicating that even under isothermal conditions, stresses are relieved by a scale-cracking mechanism. For oxide scales on TiAl surfaces, which had been ion implanted with chlorine before oxidation, a very thin protective alumina layer is formed which, however, develops growth stresses in the range of several GPa, accompanied by intensive acoustic emission. In all stress–time curves, a dynamic situation is observed. This consists of phases of stress relief by scale microcracking and phases of stresses increase due to crack healing and further oxide growth. As a result, the level of stress as a function of oxidation time, is characterized by an oscillating course.     

Quantitative analysis of Ni effect on CCT diagrams of novel air-cooled bainite steels using artificial neural network models

The quantitative effect of Ni content on continuous cooling transformation （CCT） diagrams of novel air-cooled bainite steels was analyzed using artificial neural network models. The results showed that Ni may retard the high- and medium-temperature transformation and martensite transformation. The results conform to the materials science theories.     

场激活加压燃烧合成WC-Ni复合材料的工艺参数研究

以钨、碳和镍为原料,在电场激活下,材料的燃烧合成和致密化同时进行,短时间内完成了碳化钨镍复合材料的制备。研究了场激活 加压燃烧合成中的工艺参数,如脉冲电流、能量控制模式、升温速率、最高温度和压力对反应的影响。测量了在反应合成和致密化前后的样品 收缩率。所制备的复合材料的相对密度,490N载荷下Vickers硬度和断裂韧性分别为99.2%,13.965GPa和5.9MP·m1/2。     

熔融碳酸盐燃料电池阴极材料的导电性

通过交流阻抗方法研究了熔融碳酸盐燃料电池阴极材料锂镍氧化物、锂钴氧化物和锂铁氧化物的导电性能。结果表明:锂镍氧化物电极的导电性最好,锂钴氧化物电极的导电性次之,锂铁氧化物电极的导电性最差;它们的导电性都随着温度的升高而按指数规律增加;在合成锂钴氧化物(或锂铁氧化物)的过程中,使Li2CO3轻微过量,可以提高锂钴氧化物(或锂铁氧化物)电极的导电性,而且在同一温度下,随着nLi∶nCo(或nLi∶nFe,摩尔比)值的增大,锂钴氧化物(或锂铁氧化物)电极的导电性显著增加。     

Relating catalyst structure and composition to the water–gas shift activity of Cu–Zn-based mixed-oxide catalysts

In order to investigate the effect of cerium oxide on Cu–Zn-based mixed-oxide catalysts four catalyst samples were characterized by means of XRD, in situ XANES and thermogravimetric analysis. The activity of the catalyst samples was tested for the forward water–gas shift reaction. Cerium oxide was found to increase the crystallinity of the ZnO phase indicating a segregation of the Cu and ZnO phases. The TOF of the water–gas shift reaction based on chemisorption data was found to be independent of composition and preparation conditions of the four catalyst samples. In contrast, the catalyst stability depends on composition and preparation conditions. Cerium oxide impregnated before calcination of the hydrotalcite-based Cu–Zn precursors leads to a more stable water–gas shift catalyst.     

介孔氧化铁对正辛醇乙氧基化反应的催化性能

以十二烷基磺酸钠为模板剂、乙二胺为碱性介质,将水热法合成的氧化铁/十二烷基磺酸钠复合中孔材料在550℃、空气气氛中煅烧10h,除去模板剂,得到介孔氧化铁。通过X射线衍射、氮气吸附-脱附方法对介孔氧化铁的晶体结构和表面物性进行表征。表征结果显示,煅烧后的介孔氧化铁具有典型的六方介孔的结构特征,平均孔径为5.4nm。将介孔氧化铁用于催化正辛醇乙氧基化反应,研究结果表明,升高反应温度和初始压力、增加催化剂用量,可加快环氧乙烷的反应速率,同时产物的相对分子质量分布较窄。当平均聚合度为6.5时,正辛醇聚氧乙烯醚相对分子质量分布的选择性系数达到21.1。     

Formation and electronic structure of interface

In the present work the formation of the interface between polycrystalline silver and thin films of titanium oxide was studied with photoelectron spectroscopy (XPS, UPS) and time-of-flight secondary ion mass spectrometry (TOF-SIMS). Titanium oxide was deposited stepwise on 100 nm thick silver films by reactive magnetron sputtering allowing to study the evolution of the interface formation process. The process involves two steps: formation of thin layer of silver oxide and subsequent growth of the TiO₂ film. For better understanding of the silver oxidation process, pure silver films were exposed to a low temperature Ar/O plasma for different time intervals providing a possibility to investigate early stages of the oxide film growth.     

Preparation and Properties of Rare Earth Modified Carbon Black/Natural Rubber Composites

The oxides Eu, Ho, Er and Dy were used to prepare the hydroxides of rare earth modified carbon black. Then natural rubber latex （NRL） was added into the reactor. The system reacted at 85 ℃ with stirring for 1 h to prepare powdered HAF-Ln（OH）3/NR composites. The effects of the kind and content of Ln on the particle size distribution of P [ NR/HAF-Ln （OH）3 ] and mechanical properties of its vulcanizate were studied respectively. It is found that rare earth can help to get the powder of the composite, the product particle with a diameter less than 0.9mm will be get when the composites containing the compound of Ho, Er and Dy with dosage of 1.0, 1.0, O. 5 percent, respectively. The adding of Ln can improve the tensile strength and tear strength of the vulcanizate effectively, what＇s more, Er and Dy can decrease the permanent set of vulcanizate significantly. The SEM studies shows that P[ NR/HAF-Dy （OH）3 ] vulcanizate shows superior mechanical properties that depend primarily on the absence of free carbon black, the fine dispersion of carbon black in the rubber matrix and better polymer-filler interaction.