超高吨位灌注桩静载试验中的预应力混凝土反力装置

在复兴大桥超高吨位灌注桩的静载试验,预应力混凝土反力装置替代了传统的钢梁反力系统。这套装置主要包括预应力锚桩、预应力承台与预应力反力梁。试验结果表明,直接获得超高吨位大直径嵌岩桩的极限承载力相当不易,而对这类问题预应力混凝土反力装置是值得考虑的。     

Diurnal and environmental characterization of solar photovoltaic panels using a PC-AT add on plug in card

This article describes the development of an instrumentation system for characterizing photovoltaic panels. It uses an add on card (which contains DAC, ADC and digital input/output ports) in conjunction with a PC-AT. The panels in a field are selected in succession through a set of relays actuated by the digital output port. The selected panel is loaded in discreet steps by a transistor loading circuit which is activated by the digital to analog convertor to trace the most significant portion of the I-V curve. The data shows that the power output is invariably lower than that specified by the manufacturer. The reasons for drop in output have been analyzed. It is shown that these effects can be represented by the curvature of I-V characteristic at the maximum power point (OP). The loss of power due to accumulation of dust and the increase in temperature of the panels can be significant.     

非牛顿流体在气液搅拌槽内强制流动传热特征研究

为了确定非牛顿流体气流搅拌流动传热特征，对气体有效分散区域（载点）提出了无因次准数关联式，并就两种不同叶轮搅拌的通气管外传热系数作了比较。     

V型天线的行波加载公式

本文研究了ｖ型天线上电流分布与阻抗加载的关系，导出了支持天线上行波电流的阻抗加载公式。讨论了天线张角、振子半径以及振子长度与加载量的关系和规律，说明了加载Ｖ型天线的宽带特性。文中还计算了在高斯脉冲激励下，不同加载量的天线上瞬态电流的分布，由此可以表明所导加载公式的正确性与重要性。     

土石坝工程领域的若干创新与发展

我国高土石坝数量居世界之首,保证高坝大库建设与长期运行安全是国家经济和公共安全保障的重大需求。系统总结了长江科学院近年来在土石坝工程领域的若干创新与发展。提出了基于“旁压模量当量密度法”的粗粒料级配相似理论试验方法;介绍了研发的系列CT三轴仪,实现了粗粒料组构要素的定量测量;提出了三轴试验中加载板与试样之间由滑动摩擦变为滚动摩擦、整体式接触变为分散式接触的减摩新方法,研发了相关减摩装置;研制了大尺寸、高压力、微摩擦、刚柔复合加载的土工真三轴仪;揭示了粗粒料真实三维应力条件下的强度与变形变化规律、湿化与蠕变变形特性;构建了粗粒料三参量非线性K-K-G剪胀模型、六参数湿化模型、九参数蠕变数学模型及相应的参数确定方法;基于当量密度法的原创思想,提出了利用旁压试验间接确定超百米级深厚覆盖层现场密度的试验方法。上述研究成果可为高土石坝工程建设提供重要科技支撑。     

石英砂加载混凝工艺的DOM去除特征与混凝机理

为处理未纳入管网的市政污水,采用石英砂加载混凝工艺,考察石英砂的粒径及其投加量对处理效能的影响,分析了溶解性有机物(dissolved organic matters,DOM)的去除特征,并探讨了石英砂加载混凝机理。结果表明,与常规混凝相比,当石英砂的粒径和投加量分别为200目和 1.0 mg/L 时,石英砂加载混凝工艺对污水中浊度、COD的去除率分别为97.55%、59.2%,优于常规混凝;石英砂加载混凝工艺可明显去除芳香类、共轭双键、疏水性有机物,主要促进了腐殖质类物质的削减;石英砂通过架桥作用增加了絮体的密度,进而显著改善了絮体的沉降性能、强度;絮体的沉降性能、强度及再稳性能随着石英砂粒径的降低而升高。     

An improved bacterial foraging algorithm for combined static/dynamic environmental economic dispatch

Economic dispatch is carried out at the energy control center to find out the optimal output of thermal generating units such that power balance criterion is met, unit operating limits are satisfied and the fuel cost is minimized. With growing environmental awareness and strict government regulations throughout the world, it has become essential to optimize not only the total fuel cost but also the harmful emissions, both, under static as well as dynamic conditions. The static environment economic dispatch finds the optimal output of generating units for a fixed load demand at a given time, while the dynamic environmental economic dispatch schedules the output of online generators with changing power demands over a certain time period (normally one day) so as to minimize these two conflicting objectives, simultaneously. In this paper, the price penalty factor approach is employed for simultaneous minimization of cost and emission. The generator ramp rate constraints, non-convex and discontinuous nature of cost function and the large number of generators in practical power plants, make this problem very difficult to solve. Here, a fuzzy ranking approach is employed to identify the solution which offers the best compromise between cost and emission objectives.     

一种高效的同尺寸长方体的装箱算法

针对应用广泛的同尺寸长方体货品的装箱问题,本文运用分层装载方案,根据货品的长宽高采用三种不同的层高,利用动态规划算法分别计算三种层的最大装载量,再通过背包算法对层进行组合,得出装箱的最优方案。该算法复杂度低,装载方案简单。     

双轴加载条件下疲劳裂纹扩展的研究

在双轴加载条件下对Ⅰ型疲劳裂纹扩展进行了研究。载荷范围从0.08σ_s到0.71σ_3,包括比例加载和非比例加载。基于对Von Mises理论的讨论,提出一个新的力学参数。双轴加载条件下的弹塑性参数P成功地描述了双轴比例加载和非比例加载下的疲劳裂纹扩展。     

加载速率对结构钢力学性能和断裂韧度的影响

在常温下进行了常用建筑结构钢(16Mn和Q235B钢)动态拉伸和动态断裂韧度试验。试验结果表明，材料在动载下无论是屈服强度还是抗拉强度均有一定的提高，塑性有了一定的降低；由于缺口尖端区域温度的升高，常温下动载对于16Mn钢母材和焊缝的断裂韧度是有利的；Q235B钢常温下，焊缝的断裂韧度值较低，且动载对母材的断裂韧度影响较大，和静载相比动载下断裂韧度值降低了4倍有余，可以看出，Q235B钢的抗震性能较差。通过研究发现，对于低韧度水平的材料，研究动载下结构的断裂行为时．材料的强度也应该作为一个考虑因素。