从煤炭、天然气制取石油石化产品工艺技术

在阐述煤炭、天然气通过吹氧气化制取CO +H2 合成气联产石油石化产品的基础上 ,详细介绍了甲醇、二甲醚、乙烯生产工艺技术的应用与开发 ,对各种工艺路线进行了论证和技术经济评估     

变压吸附富氧工艺用于合成氨制气过程的技术经济分析

本文介绍了变压吸附法制备富氧空气用于合成氨造气系统的新工艺，并对５００００ｔ／ａ合成氨厂进行了技术经济评估。结果表明，同间歇法气化相比，该技术工艺先进且具有显著的经济效益。     

A_1-A_2-O-M工艺处理焦化废水的实验研究

采用厌氧-缺氧-好氧-复合(A1-A2-O-M)工艺处理焦化废水,考察了外加碳源和碱源对焦化废水COD和NH4+-N脱除效果的影响。试验结果表明:外加甲醇和碳酸氢钠对焦化废水的硝化和反硝化效果影响很小;不外加碳源和碱源时,焦化废水经处理后出水的COD和NH4+-N平均质量浓度分别为125.0mg/L和1.12mg/L,分别达到《污水综合排放标准》(GB8978-1996)中的二级标准和一级标准。     

Surface and subsurface products of the interaction of O2 with Ag under catalytic conditions

Polycrystalline Ag treated with O₂ at pressures up to 1 bar and at temperatures up to 920 K was examined by TDS. It was found that the peak commonly observed at 595±25 K and assigned to adsorbed atomic oxygen (O_a) is shifted to higher desorption temperatures with rising dosing temperatures. Since saturation of the uptake was not possible either, this peak was identified as dissolved atomic oxygen (O_d). The existence of a maximum for the O₂ uptake after exposure at 820 K was found. Hence, under conditions of formaldehyde synthesis ( 920 K) the ability of the catalyst to dissolve oxygen is near its maximum.     

Augment low-field intra-operative MRI with preoperative MRI using a hybrid non-rigid registration method

Background

Preoperatively acquired diffusion tensor image (DTI) and blood oxygen level dependent (BOLD) have been proved to be effective in providing more anatomical and functional information; however, the brain deformation induced by brain shift and tumor resection severely impairs the correspondence between the image space and the patient space in image-guided neurosurgery.

Method

To address the brain deformation, we developed a hybrid non-rigid registration method to register high-field preoperative MRI with low-field intra-operative MRI in order to recover the deformation induced by brain shift and tumor resection. The registered DTI and BOLD are fused with low-field intra-operative MRI for image-guided neurosurgery.

Results

The proposed hybrid registration method was evaluated by comparing the landmarks predicted by the hybrid registration method with the landmarks identified in the low-field intra-operative MRI for 10 patients. The prediction error of the hybrid method is 1.92 ± 0.54 mm, and the compensation accuracy is 74.3 ± 5.0%. Compared to the landmarks far from the resection region, those near the resection region demonstrated a higher compensation accuracy (P-value = .003) although these landmarks had larger initial displacements.

Conclusions

The proposed hybrid registration method is able to bring preoperatively acquired BOLD and DTI into the operating room and compensate for the deformation to augment low-field intra-operative MRI with rich anatomical and functional information.     

改进氧气分布器,提高醋酸质量和收率

通过对氧气分布器的形状和孔径、开孔率进行分析,找到了湘维醋酸装置醋酸质量和醋酸收率偏低的原因.采用临界孔径和临界气速的理论对湘维醋酸装置氧气分布器进行了设计,实施后抑制了副反应,提高了醋酸质量和醋酸收率.     

Electrosynthèse des ions peroxodiphosphate sous potentiel constant ou pulsé

Electrosynthesis of peroxodiphosphate ions (P2O84–) was performed in 2m K3PO4, 1m K2HPO4 medium, using a platinum anode. The results showed that under conditions of potentiostatic polarization at constant potential, the reaction rate reaches a maximum value of 125mAcm–2 and a faradaic yield of 30%. From about 1.9V, the reaction kinetics are increasingly inhibited as the potential shifts positively. Rapid scanning potential voltammetry was used to characterize the oxidation state of the electrode surface. This method shows that the growth of (PtO) and (PtO2 or PtO3) oxides depend on the applied potential. It also establishes a correlation between the inhibition of P2O84– ion electrosynthesis and the oxide coating surface. When 2×10–3m KSCN is added to the solution, some oxygen evolution sites are selectively blocked and oxide occurs at more positive potential values. Consequently, the rate of peroxodiphosphate ion formation and the faradaic efficiency are increased to 380mAcm–2 and 75%, respectively. Under pulsed potential conditions it was possible to reach 1200mAcm–2 for P2O84– ion electrosynthesis with a faradaic yield of 82%.     

氟树脂涂料中氟含量测定方法的探讨

讨论了以氧气瓶燃烧法分解氟树脂,把氟树脂中的氟转化为氟离子,然后以硝酸镧标准溶液进行滴定,从而测定出氟树脂中的氟含量,再根据定量关系计算出氟树脂涂料中的氟含量的方法。该方法简单易行,准确可靠,省时省力。     

碳纤维经氧等离子/KH550处理后的表面形态和结构

碳纤维(CF)表面经氧等离子、KH550和 LiAlH_4处理后,其物理和化学性能得以改善.由于提高了 CF 和树脂间的联结,使 CF 复合材料的层间剪切强度提高50%以上,在湿热下的强度保留率达94%以上.使用纤维接触角测定仪,SEM 和 XPS 等对 CF 表面的浸润性、形态和化学组成进行了研究.实验指出:CF 经等离子和 KH550处理后,其临界表面能有了提高;CF 本身仅受氧离子刻蚀,故其拉伸强度的损失小于其他处理方法.