液态中锰渣摇包生产高硅锰硅合金的探讨

论述了利用液态中锰渣摇包生产高硅锰硅的原理、工艺过程热平衡,并介绍了其操作过程、主要影响因素及所取得的经济、社会效益.     

水冷热模法离心铸造大口径球铁管用管模涂料

阐述水冷热模法管模涂料的组成。说明了耐火基料，悬浮剂、粘结剂，减水剂的各自作用机理，提出了合理的涂料配方、合适的喷涂方式。     

麻辣香肠的研制

香肠作为具有中国特色的传统肉制品，倍受广大消费者的喜爱，然而传统香肠单一口味已不能满足那些喜爱吃麻辣口味的消费者的需求，特别是在秋冬季节，吃麻辣已成为一种流行趋势，开发麻辣口味香肠，迎合消费者需求已是一种趋势；本试验采用正交设计方案。确定食盐、白糖、红辣椒粉、复合香辛料的添加量分别为：3％、2％、0．5％、0．41％。     

成形工艺对快速凝固Al—Cu—Mg合金组织和性能的影响

采用自制离心雾化装置制取了快速凝固LY12硬铝合金粉末,研究了以该粉末制成的真空热压件和挤压丝材的组织和性能。结果表明,所得粉末为泪滴状,其显微组织为树枝状晶和胞状晶。真空热压件密度高时所对应的强度高。450℃、10min、150MPa为较合理的工艺,此时粉末颗粒间结合密实,晶粒尺寸没有明显改变。在500℃热挤压时,挤压丝的组织已发生了再结晶,晶粒尺寸仍较细小。挤压丝材的抗拉强度达460MPa,其断口为韧窝状,韧窝尺寸小于3μm,且分布均匀。     

孔型热轧时轧制力的实用计算公式

采用修正系数法,利用板材在带刻槽的冲头进行深冲与平面冲头下深冲时的接触压力的比值确定孔型影响系数,进而推导出孔型热轧时轧制力的实用计算公式.     

熔融 NaCl-(Na,K)_2SO_4引起的 Fe-Cr 合金的热腐蚀

本文采用电化学方法研究了 Fe-Cr 合金在800℃、熔融 NaCl-(Na,K)_2SO_4中的腐蚀行为,并对腐蚀产物进行了观察和分析。结果表明,提高合金 Cr 含量可以改善合金耐蚀性能。氧化-硫化是Fe5Cr、Fe10Cr 合金腐蚀破坏的主要方式;氧化膜的熔融反应是 Fe20Cr、Fe25Cr 合金加速腐蚀的主要原因。同时,氧化膜的机械破裂也加速了合金的腐蚀。     

连铸坯红送热装应用效果分析

对加热炉用连铸坯红送热装效果的分析结果表明，该技术的应用可节能降耗，提高产量和加热质量。     

Partitioning multiple objective optimal solutions with applications in radiotherapy design

The optimal partition for linear programming is induced by any strictly complementary solution, and this partition is important because it characterizes the optimal set. However, constructing a strictly complementary solution in the presence of degeneracy was not practical until interior point algorithms became viable alternatives to the simplex algorithm. We develop analogs of the optimal partition for linear programming in the case of multiple objectives and show that these new partitions provide insight into the optimal set (both pareto optimality and lexicographic ordering are considered). Techniques to produce these optimal partitions are provided, and examples from the design of radiotherapy plans show that these new partitions are useful. A. Holder. Research conducted at Trinity University, TX, and The University of Mississippi, MS. This research was partially supported by ONR Grant N00014-01-1-0917.     

Phase Composition of Oxide Scales during Reheating in Hot Rolling of Low Carbon Steel

Low carbon steel was oxidized over the temperature range 1000‐1250°C in O₂‐CO₂‐H₂O‐N₂, O₂‐H₂O‐N₂, and O₂‐CO₂‐N₂ gas mixtures. Oxidation times were 12‐120 min. and the scales were 50‐2000 μm thick. The variations of these parameters were chosen to elucidate the phase composition of oxide scales under conditions similar to those of reheating furnaces in hot strip mills, using either thin slab casting or conventional casting and rolling technology. Two types of scales have been observed which are influenced by the furnace atmosphere, oxidation time, and temperature. The first type is a crystalline scale with an irregular outer surface, composed mostly of wustite (FeO), and a negligible amount of magnetite (Fe₃O₄). The second type is the classical three‐layer scale, composed of wustite (FeO), magnetite (Fe₃O₄), and hematite (Fe₂O₃). In general, the experiments showed that an increase in oxidation time decreased the percentage of wustite while the percentages of magnetite and hematite increased. A rise in oxygen concentration in the gas mixture increased the percentages of magnetite and hematite, confirming earlier experimental findings. In water vapour‐free atmospheres O₂‐CO₂‐N₂, the oxide scales had a low percentage of wustite, and high percentage of magnetite and hematite. Carbon dioxide showed a small influence at 1100°C, and a negligible one at 1250°C.