Thermal transport and chemical conversion in single reacting sorbent particles

The effects of particle size and carbon dioxide concentration on chemical conversion in engineered spherical particles undergoing calcium oxide looping are investigated. Particles are thermochemically cycled in a furnace under different carbon dioxide concentrations. Changes in composition due to chemical reactions are measured using thermogravimetric analysis. Gas composition at the furnace exit is evaluated with mass spectroscopy. A numerical model of thermal transport phenomena developed previously is adapted to match the physical system investigated in the present study. The model is used to elucidate effects of reacting medium characteristics on particle temperature and reaction extent. Experimental and numerical results show that (1) an increase in particle size results in a decrease in carbonation extent, and (2) the carbonation step consists of fast and slow reaction regimes. The reaction rates in the fast and slow carbonation regimes increase with increasing carbon dioxide concentration. The effect of carbon dioxide concentration and the distinction between the fast and slow regimes become more pronounced with increasing particle size.     

Electrical and magnetic properties of double perovskite: Y2CoMnO6

In this communication, the structural, micro-structural, dielectric, electrical, magnetic, and leakage-current characteristics of a double perovskite (Y₂CoMnO₆) ceramic material have been reported. The material was synthesized via a high-temperature mixed-oxide route. The compound crystallizes in a monoclinic structure which is confirmed from preliminary X-ray structural study. The morphological study by using scanning electron micrograph reveals the almost homogeneous distribution of grains throughout the surface of the sample. The nature of frequency-dependence of dielectric constant has been described by the Maxwell-Wagner model. The occurrence of a dielectric anomaly in the temperature dependence of dielectric permittivity study demonstrates the ferroelectric-paraelectric phase transition in the material. From the Nyquist plots, we found the existence of both grain and grain boundary effects. The frequency dependence of conductivity was studied by the Jonscher’s Power law, and the conduction phenomenon obeys the large overlapping polaron tunneling model. By using the Arrhenius equation, the activation energy has been calculated which is nearly equal to the energy required for the hoping of the electron. Both impedance and conductivity analysis demonstrate that the sample exhibits negative temperature coefficient of resistance (NTCR) properties indicating the semiconducting type of material at high temperatures. The anti-ferromagnetic character of the material is observed from the nature of magnetic hysteresis loop. The leakage current analysis suggests that the conduction process in the material follows the space charge limited conduction phenomenon. Such material will be helpful for modern electronic devices and spintronic applications.     

Current Status of Angiogenic Cell Therapy and Related Strategies Applied in Critical Limb Ischemia

Critical limb ischemia (CLI) constitutes the most severe form of peripheral arterial disease (PAD), it is characterized by progressive blockade of arterial vessels, commonly correlated to atherosclerosis. Currently, revascularization strategies (bypass grafting, angioplasty) remain the first option for CLI patients, although less than 45% of them are eligible for surgical intervention mainly due to associated comorbidities. Moreover, patients usually require amputation in the short-term. Angiogenic cell therapy has arisen as a promising alternative for these “no-option” patients, with many studies demonstrating the potential of stem cells to enhance revascularization by promoting vessel formation and blood flow recovery in ischemic tissues. Herein, we provide an overview of studies focused on the use of angiogenic cell therapies in CLI in the last years, from approaches testing different cell types in animal/pre-clinical models of CLI, to the clinical trials currently under evaluation. Furthermore, recent alternatives related to stem cell therapies such as the use of secretomes, exosomes, or even microRNA, will be also described.     

Comparative analysis of formaldehyde and toluene sorption on indoor floorings and consequence on Indoor Air Quality

Indoor surfaces may be adsorptive sinks with the potential to change Indoor Air Quality. To estimate this effect, the sorption parameters of formaldehyde and toluene were assessed on five floorings by an experimental method using solid-phase microextraction in an airtight emission cell. Adsorption rate constants ranged from 0.003 to 0.075 m·h⁻¹, desorption rate constants from 0.019 to 0.51 h⁻¹, and the partition coefficient from 0.005 to 3.9 m, and these parameters vary greatly from one volatile organic compound/material couple to another indicating contrasted sorption behaviors. A rubber was identified as a sink of formaldehyde characterized by a very low desorption constant close to 0. For these sorbent floorings identified, the adsorption rates of formaldehyde are from 2 to 4 times higher than those of toluene. Two models were used to evaluate the sink effects of floorings on indoor pollutant concentrations in one room from different realistic conditions. The scenarios tested came to the conclusion that the formaldehyde sorption on one rubber (identified as a sink) has a maximum contribution from 15% to 21% for the conditions of low air exchange rate. For other floorings, the sorption has a minor contribution less than or equal to 5%, regardless of the air exchange rate.     

Effects of the film thickness and poling electric field on photovoltaic performances of (Pb,La)(Zr,Ti)O3 ferroelectric thin film-based devices

The ferroelectric photovoltaic (FPV) effect obtained in inorganic perovskite ferroelectric materials has received much attention because of its large potential in preparing FPV devices with superior stability, high open-circuit voltage (V_oc) and large short-circuit current density (J_sc). In order to obtain suitable thickness for the ferroelectric thin film as light absorption layer, in which, the sunlight can be fully absorbed and the photo-generated electrons and holes are recombined as few as possible, we prepare Pb_0.93La_0.07(Zr_0.6Ti_0.4)_0.9825O₃ (PLZT) ferroelectric thin films with different layer numbers by the sol-gel method and based on these thin films, obtain FPV devices with FTO/PLZT/Au structure. By measuring photovoltaic properties, it is found that the device with 4 layer-PLZT thin film (~300 nm thickness) exhibits the largest V_oc and J_sc and the photovoltaic effect obviously depends on the value and direction of the poling electric field. When the device is applied a negative poling electric field, both the V_oc and J_sc are significantly higher than those of the device applied the positive poling electric field, due to the depolarization field resulting from the remnant polarization in the same direction with the built-in electric field induced by the Schottky barrier, and the higher the negative poling electric field, the larger the V_oc and J_sc. At a -333 kV/cm poling electric field, the FPV device exhibits the most superior photovoltaic properties with a V_oc of as high as 0.73 V and J_sc of as large as 2.11 μA/cm². This work opens a new way for developing ferroelectric photovoltaic devices with good properties.     

Digital Microfluidics for Manipulation and Analysis of a Single Cell

The basic structural and functional unit of a living organism is a single cell. To understand the variability and to improve the biomedical requirement of a single cell, its analysis has become a key technique in biological and biomedical research. With a physical boundary of microchannels and microstructures, single cells are efficiently captured and analyzed, whereas electric forces sort and position single cells. Various microfluidic techniques have been exploited to manipulate single cells through hydrodynamic and electric forces. Digital microfluidics (DMF), the manipulation of individual droplets holding minute reagents and cells of interest by electric forces, has received more attention recently. Because of ease of fabrication, compactness and prospective automation, DMF has become a powerful approach for biological application. We review recent developments of various microfluidic chips for analysis of a single cell and for efficient genetic screening. In addition, perspectives to develop analysis of single cells based on DMF and emerging functionality with high throughput are discussed.     

基于三维胞元空间的MA双向并行路由算法

针对传统移动代理(MA)在监测无线传感器网络(WSNs)的感兴趣信息时产生的延迟较大和能耗较多问题,提出了基于三维胞元空间的MA双向并行(3D-BPMA)路由算法.3D-BPMA将MA与传统的客户/服务器(c/S)模式相结合,在胞元内利用C/S模式搜集信息,在单层胞元系统和路由器与路由器之间采用MA双向并行的策略进行传输.仿真结果表明:3D-BPMA与LCF,DSG-MIP算法相比减少了平均响应时间和网络平均能耗,提高了MA发送率.