Mechanical and dynamic mechanical properties of jute fibers–Novolac–epoxy composite laminates

A study was done of jute composite using a polymer matrix of epoxidized Novolac resin (ENR), diglycidyl ether of bisphenol A (DGEBA)–based epoxy, and their blends with different weight percentages of the resins. It was found that on blending ENR with DGEBA, the storage modulii at room temperature are enhanced by about 100% or more in the case of 30 and 40% ENR‐containing matrices, whereas the enhancement in the case of 20 and 12% ENR‐containing matrices is only 50% that of the pure matrix. It was also observed that the tan δ peak heights of the composites containing 30 and 40% ENR are closer to that of 20% ENR‐containing composite. The probable explanation drawn on the basis of experimental findings of DMA and mechanical analysis is that by blending ENR with DGEBA epoxy it is possible to manufacture jute composites with increased stiffness without sacrificing their ductility. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2800–2807, 2002     

Intrinsic Elastic, Dielectric, and Piezoelectric Losses in Lead Zirconate Titanate Ceramics Determined by an Immittance-Fitting Method

The material coefficients of "soft" and "hard" lead zirconate titanate (PZT) ceramics were determined as complex values by the nonlinear least-squares-fitting of immittance data measured for length-extensional bar resonators. The piezoelectric d -constant should be a complex value to obtain a best fitting between observed and calculated results. Because the elastic, dielectric, and piezoelectric losses determined in this process were not "intrinsic" losses, a calculation process to evaluate the "intrinsic" losses was proposed. It was confirmed that the intrinsic losses were smaller than the corresponding extrinsic losses. The intrinsic piezoelectric loss existed in both soft and hard PZTs; ∼50% of the loss of piezoelectric d -constant was derived from the elastic and dielectric losses. The most notable difference between the soft and hard PZTs was observed in their elastic losses.     

准同型相界附近(Na1-xKx)0.5Bi0.5TiO3的制备及性能研究

利用固相法制备了（Na1-xKx）0.5Bi0.5TiO3系压电陶瓷，XRD分析表明所得陶瓷样品为纯的钙钛矿结构，其准同型相界在x=0．18～0．22之间；电子探针显微分析显示所做陶瓷样品晶粒发育良好，具有规则的外形和明显的晶界；实验所得陶瓷样品损耗tanδ最大不超过5％，最好的压电常数d33=153 pC／N，平面机电耦合系数kp=0．299，它们分别出现在x=0．22和0．20处。     

Damping of vinyl acetate–n‐butyl acrylate copolymers

A photopolymerization process at room temperature was devised to copolymerize vinyl acetate (VAc) and n‐butyl acrylate (BA) mainly to prepare rubber‐like damping sheet bearing pressure‐sensitive adhesive property in this study. The investigations using both the differential scanning calorimeter and rheometric dynamic analysis show the existence of two glass transition temperatures for each copolymer. The scanning electron microscopic pictures reveal that the degree of microphase separation increases with increasing annealing time at 70°C. It was suggested that the rubbery domain (formed by the PBA blocks) disperses in the glassy domain (constituted by the PVAc blocks), making an effective damping entity. Excellent damping was observed for the copolymer samples, with the tanδ peak values as high as 1.76–1.80 at a certain temperature range and with tanδ> 0.3 at quite wide temperature ranges. In addition, the copolymers containing more VAc tend to have the higher damping. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1396–1403, 2004     

压挤成形--固化法制备0-3型压电复合材料的性能研究

详细地叙述了室温压挤成形———固化工艺制备 0 -3型压电复合材料工艺 ,使用XRD、SEM和HP42 94测试并分析了样品的结构和性能 ,并与压电陶瓷性能参数进行了对比 ;同时用这种工艺制备可以获得介电损耗小、机电耦合系数为 2 5 .11%、压电应变常数为 3 2PC N和机电品质因数可达到 3 0 2的 0— 3型压电复合材料。     

国内互穿网络结构阻尼涂料的研究进展

在总结了国内聚合物基阻尼涂料的研究基础上,详细综述了互穿网络(IPN)结构、乳液互穿网络(LIPN)结构聚合物基阻尼涂料的种类及研究现状,并展望了聚合物基阻尼涂料研究的发展趋势和前景。     

惯性往复振动机械阻尼值设计的理论研究

建立了双旋转偏重激振的惯性往复振动机械的状态方程,将该状态方程与两驱动电机的状态方程一起组成机电耦合系统的数学模型,对不同阻尼的机电耦合数学模型进行数值求解,得到不同阻尼时系统的瞬态和稳态解.通过综合分析系统阻尼对最大共振振幅、启动时间、稳态功率消耗及阻尼力的影响,提出了惯性往复振动机械阻尼率的合理设计值为0.1左右.     

压电双晶片型旋转精密驱动器动态特性和控制

提出了以自由端带有集中质量的悬臂式压电双晶片为驱动单元的新型冲击式旋转精密驱动器.制作了驱动器样机,建立了基于Lugre摩擦模型的驱动器动力学模型.对驱动器动态特性进行了仿真分析和实验对比研究.根据驱动器的动态特性,提出了冲击式压电双晶片型精密驱动器特定的定频调压控制方法.仿真分析结果和实验结果吻合较好,表明该动力学模型符合驱动器的动态特性,可用于对冲击式压电双晶片型旋转精密驱动器的理论分析.     

Alkaline treatment kinetics of calcium phosphate by piezoelectric quartz crystal impedance

Calcium phosphate film was prepared by electrochemical deposition technology. Subsequently, the alkaline treatment process of calcium phosphate film in 0.1 mol/L NaOH solution was monitored on real time by the piezoelectric quartz crystal impedance (PQCI) technique. The variations of morphology and composition for the alkaline treatment products were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) and X-ray diffraction (XRD), respectively. The dynamic variations of calcium phosphate can be characterized by the change of equivalent circuit parameters. The results show that the forming process of hydroxyapatite (HA) is composed of three stages: (1) acidic calcium phosphate dissolution; (2) phase transformation; and (3) HA formation. Furthermore, the correlative kinetic equations and parameters are obtained by fitting the static capacitance (C _s)—time curves. Foundation item: Project(2005CB623901) supported by the Major State Basic Research and Development Program of China     

智能材料二维问题的状态空间解

抛弃任何有关位移或应力模式的人为假设,引入状态空间理论,从压电、压磁智能材料和电磁耦合弹性介质材料二维问题的基本方程出发,建立了压电、压磁智能材料和弹性介质二维问题的状态变量方程,得到状态变量空间解,此解形式简单、便于应用.