可发泡性酚醛树脂的合成研究

考查了可发泡性酚醛树脂的合成条件,如反应时间、温度和催化剂用量等对树脂活性、物理以及酚醛泡沫塑料容重和表观品质的影响,结果表明:催化剂用量越大,树脂粘度越大,泡沫固化时间越长;反应时间介于65～95min,泡沫塑料容重和表观品质较好;用加热板测定了合成的可发泡性树脂的固化速度,并求出固化反应活化能。     

Epoxy-Polysulfone Networks as Advanced Matrices for Composite Materials

Compatibility between polysulfone (PSF) and epoxy oligomers in the melt state as well as the morphology and properties of alloys obtained were studied as a function of composition. The compatibility depends on the length and structure of epoxy molecules, and is best in the case of epoxysulfone oligomers (ESO).

The properties of hybrid matrices are determined by their composition and morphology. The most pronounced effects are observed in the regions of small concentrations of either component. A small quantity of PSF significantly improves thermal stability and heat resistance of the epoxy resin as well as its impact strength. On the other hand, on addition to PSF of small amounts of epoxysulfone oligomers, the processability of the matrix can be substantially improved. In particular, the melt viscosity decreases, and wetting and impregnation of fibrous reinforcement is facilitated. Besides, the matrix adhesion to fibers is increased.

Powdered PSF/ESO/curing agent mixtures are good for application in solvent-free technological processes of fibrous composites production, e.g. in electrostatic deposition of matrix particles onto a reinforcing fabric. Plastics based on hybrid matrices are distinguished by improved strength.     

泡沫塑料主要力学性能及其力学模型

描述发泡塑料力学性能的模型,讨论了普通发泡塑料的力学性能以及它和发泡塑料密度的关系。并且比较了硬质聚氨酯(RPUR)和聚氯乙烯(PVC)泡沫塑料的主要力学性能随密度的变化。最后介绍了微孔发泡塑料的几项优良的力学性能。     

Effect of coal filler on the properties of soy protein plastics

The influence of ultrafine coal filler (UFC) content on tensile properties, water absorption, and biodegradability of soy protein plastics were investigated. The addition of UFC in the soy protein plastics, with different content of glycerol as a plasticizer, was at different ratio varying from 10:0 to 6:4. Blend sheets of the soy protein composites were prepared by the compression molding processing. The results show that, with 23.08 wt % glycerol, the tensile strength and elongation at break for the soy protein sheet with coal filler (range from 5 to 30 parts) can be enhanced as compared with nonfilled soy protein plastics. Water resistance of the soy protein plastics improves with the increase in UFC content. The derivative thermogravimetry (DTG) curves indicate a double‐stage degradation process for defatted soy flour (SPF), while three‐stage degradation process for soy plastics and the soy protein composites. FT‐IR, XPS, and SEM were applied to study the interfacial interaction between coal macromolecules and soy protein molecules in UFC filled soy protein plastics. The results demonstrated that there is strong interfacial interaction in the soy protein plastics caused by the compression molding processing. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3134–3143, 2006     

塑料挤出成型模具流道优化设计

本文依据流变学理论，采用优化方法进行挤出成型模具（即机头）流道设计，探讨了建立流道优化数学模型的有关问题。     

1991—1992国外工程塑料进展

介绍了1991～1992年国外工程塑料研究和生产概况。论述了通用工程塑料、特种工程塑料和聚合物合金的研究开发、改性和应用方面的进展。且指出工程塑料发展趋势和特点;对复合材料技术进展作了较详尽的分析与阐述。     

淀粉-聚乙烯醇可生物降解塑料研究进展

本文详细综述了近年来国内外淀粉基聚乙烯醇塑料的研究进展。     

现代塑料注射成型机的操作技术

主要介绍了现代塑料注射机的操作技术,对注射机动作选择作了较详细的介绍,也简要介绍了塑料注射成型工艺的控制原则和注射机操作的注意要点,对于注射机操作过程中可能出现的问题结合实际经验进行了分析,以期对从事塑料注射成型加工的人员有所帮助。     

导电性塑料的研究进展

本文介绍了导电性塑料的发现、分类、品种、应用、研究重点和发展前景。对导电性高聚物的一般合成方法如链聚合法和分步聚合法、特殊的合成方法如光化学聚合进行了总结，并对共轭高聚物的导电机理作了简单的评述。     

挤出机各段温度对开孔型橡塑共混材料性能的影响

研究开孔型橡塑共混材料在不同挤出加工工艺中结构形态及力学性能的变化规律。结果表明，挤出机的机头温度应稍高于发泡剂的分解温度，均化段温度要设在发泡剂分解温度区的低温段，在挤出加工工艺中，要特别注意挤出机均化段温度及机头温度的设定，温度设定不好会使发泡剂无法发挥作用。