Effect of C/Ti ratio on the laser ignited self-propagating high-temperature synthesis reaction of Al-Ti-C system for fabricating TiC/Al composites

TiC/Al composite was successfully synthesized utilizing laser ignited self-propagating high-temperature synthesis (SHS) of Al-C-Ti system with the different C/Ti molar ratio. When the molar ratio of C to Ti is below 1:1 in the starting materials, in addition to fine TiC particulates, a large amount of Al₃Ti phase was found in the composites; however, when the molar ratio of C to Ti is 1:1 in the starting materials, the Al₃Ti phase was almost completely eliminated and the distribution of TiC particulates generally appeared to be more homogeneous throughout the products synthesized.     

KATRIN NEG pumping concept investigation

The Karlsruhe Tritium Neutrino experiment (KATRIN) is going to use a very large electro-static tandem spectrometer to measure the electron spectrum from the tritium beta decay, where several kilometers of non-evaporable getter (NEG) strips (type ST707) are to be used to achieve the UHV requirements. Different geometrical configurations of the NEG strips have been studied by Monte Carlo simulations. It is shown that the resulting pumping speed of the getter pumps will allow to get a pressure below 10⁻¹¹ mbar in the huge vessel with a volume of 1400 m³. By systematic assessment of the statistics of the pumping surfaces, it could be demonstrated that the design is sound.     

运用PLC技术改造385m~2凯利式叶滤机控制系统

根据生产实践 ,结合PLC的技术特点和 385m2 凯利式叶滤机的电气联锁特性 ,阐述了应用PLC技术 ,可进一步提高 385m2 凯利式叶滤机的运转率和自动化水平。     

Influence of Ni Interlayers on the Mechanical Properties of Ti6Al4V/(WC-Co) Friction Welds

Ni interlayers were introduced prior to dissimilar friction welding of Ti6Al4V base material to three cemented carbide substrates. The fracture strength of Ti6Al4V/(WC-6 wt% Co) welds were poor and were markedly improved when 20-µm thick Ni interlayers were introduced prior to dissimilar friction welding. These results were only produced when the (WC-6 wt% Co) cermet was electroplated prior to friction welding. When the Ti6Al4V alloy was electroplated prior to friction welding, fractured WC particles and cracking were observed in the (WC-Co) carbide substrate. The fracture strengths of Ti6Al4V/(WC-11 wt% Co) and Ti6Al4V/(WC-24 wt% Co) welds were not improved when 20-µm thick Ni interlayers were introduced prior to friction welding. During mechanical testing, the Ni layer retained at the dissimilar joint interface created a region of weakness.     

溶胶-凝胶生物玻璃多孔材料显微结构和生物活性的扫描电镜及红外光谱分析

本文利用溶胶．凝胶法制备了CaO-P2O5-SiO，系统生物活性玻璃，并以其为原料制备了用于骨修复及骨组织工程支架的块状生物活性材料。利用体外实验方法(invitro)结合x射线衍射(XRD)、扫描电子显微镜(SEM)和傅立叶变换红外光谱分析(FTIR)技术对不同烧结工艺制备的材料结构、晶相和生物活性的影响进行了分析研究。研究表明，经800℃和1100℃烧结5min的两种材料均有硅磷酸钙Ca5(PO4)2SjO4微晶相析出。烧结温度越高，析出微晶相的体积比例越大，材料的生物活性则越低。在模拟生理溶液中碳酸羟基磷灰石(HCA)只在烧结体中的玻璃颗粒表面形成，而在其硅磷酸钙Ca5(PO4)2SiO4微晶相表面未发现HCA形成。     

未来航空润滑油基础油

介绍了未来航空涡轮发动机对润滑油性能的要求:在260,-54℃时,试样运动黏度分别大于1.0 mm2/s和小于15 000 mm2/s,热氧化安定性温度为260~427℃。该要求已超出了目前使用的酯类润滑油所能承受的最大极限。为了满足要求,需开发全氟聚醚、改性硅油、聚苯醚、C-型醚、氟醚三嗪及环三磷偶氮润滑油基础油,它们的使用温度依次为:-34~316,-60~260,5~288,-29~260,-30~343,-15~343℃。     

乙烯装置失效模式分析及基于风险的检验

简述了乙烯装置的工艺流程,分析了装置中常见的几种失效模式及其分布;以乙烯裂解装置为例,简述了RBI的执行过程和结果,从基于风险的检验理念,对制订设备检验策略提出了几点建议。     

A novel optical burst switching scheme—logical cascaded private subnet with start wavelength assignment policy

Many recent studies have convincingly demonstrated that network traffic exhibits a noticeable self-similar nature, which has a considerable impact on network performance, and most studies of optical burst switching (OBS) networks are under a fundamental assumption that full wavelength conversion is available throughout the network. In practice, however, economic and technical considerations are likely to dictate a more limited and sparse deployment of wavelength converters in the optical network. Therefore, we present a novel scheme for OBS networks, called logical cascaded private subnet (LCPN) with start wavelength assignment policy. We define the concept of canoe relative to cluster in self-similar traffic, and introduce a new device named payload segregator at the edge node as a gateway to the core node in OBS Networks. According to the changes in the edge node framework, we put forward the concept of cluster private subnet and canoe private subnet in the core node correspondingly. A new start wavelength assignment policy is proposed for the absence of (full) wavelength conversion capabilities in the core node of OBS Networks. The performance study indicates that, our new scheme is robust under self-similar traffic and wavelength continuity constraint.     

金属包覆平板波导模式特性的有限元法分析

采用有限元法（FEM）分析了具有复数折射率的金属包覆介质波导的模折射率与模场分布情况。计算了具有损耗层的6层介质平板波导模折射率，并与解析解比较，二者有较好的一致性；分析了金属包覆3层平板波导中TM模折射率与波导芯厚度的变化关系，计算了金属包覆5层平板波导中TM模折秧经与金属层厚度的变化关系，并结合对模场分布的分析对模式进行了定性判断，给出了其模式演变过程。