三元乙丙橡胶－甲基丙烯酸甲酯溶胀机械接枝共聚研究

采用直接溶胀法，在叶片混合器中以不同条件制备了三元乙丙橡胶－甲基丙烯酸甲酯接枝共聚物。通过动态力学粘弹谱表征，该接枝共聚物具有稳定的双相体系相态。在适宜条件下，可以制得较好综合性能的接枝共聚物。     

导静电乳液胶粘剂的研制

用多元乳液共聚法制备了用于粘贴导静电PVC地板胶粘剂,加入乙炔碳黑赋予乳液胶粘剂导静电性能。研究了影响胶接强度和初粘力的主要因素,确定m(VAc)/m(BA+VAc)较合适比为1∶3;研究了乳化剂和交联单体对乳液性能的影响,研究得出,适量加入AA和HMAM可以减少乳化剂的用量,提高乳液的性能;考查了影响导静电性能的因素,研究表明,导静电性能由乙炔碳黑决定,其加入量越大,导静电性能越好。得到的导静电乳液胶粘剂胶接强度达到0.51MPa以上,导静电可达到7.2×103Ω,两项指标均超过国家标准。     

阳离子改性苯乙烯-马来酸酐共聚物的制备与表征及应用

以2,3-环氧丙基三甲基氯化铵(ETA)为阳离子化试剂,对苯乙烯-马来酸酐共聚物(SMA)进行阳离子化改性,制备出一种阳离子性高分子分散剂(SMG)。通过红外光谱、含氮量、表面张力以及溶解性等的测定,研究了SMG的结构与性质;通过对颜料黄14的分散性考察,研究了SMG的分散性能。结果表明,SMA在阳离子化过程中,酸酐基团全部开环,部分形成酯键,阳离子化度达到7.5%左右;SMG的表面活性较低,但对颜料黄14的分散稳定性较好,在pH=7.0条件下,可以使颜料的Zeta电位提高至 35.4 mV。     

原子转移自由基聚合法制备聚乳酸三嵌段共聚物的研究

以自制的双端羟基聚乳酸与α-溴代丙酰溴反应而制得的含溴端基的聚乳酸为大分子引发剂,溴化亚铜/2,2′-联吡啶为催化体系,研究了N-乙烯基吡咯烷酮的原子转移自由基聚合行为,制得了具有两亲性聚乳酸嵌段共聚物。随单体/引发剂摩尔比的增大、聚合温度的升高,共聚物溶液的特性黏度增大,共聚物薄膜的吸水率增加;共聚物在不同降解介质中的降解规律相似,均随降解时间的延长,共聚物薄膜的失重增加,且在不同介质中呈现的降解速率表现为碱液>酸液>水>缓冲液。对聚合物进行了结构表征。     

PP-R管材料熔融挤出过程MFR控制研究

分析了PP-R（无规共聚聚丙烯）管材料MFR（熔体流动速率）的变化对力学性能的影响，着重通过双螺杆挤出机研究了PP—R管材料熔融挤出过程中影响MFR变化的因素。结果表明，合适的加工工艺控制和优良的抗氧体系是保证PP-R管材料加工过程中MFR稳定的前提。     

AM／AMPS／AMC16S共聚物的合成与性能

采用氧化－还原引发体系合成了丙烯酰胺（ＡＭ）／２－丙烯酰胺基－２－甲基丙磺酸（ＡＭＰＳ）／２－丙烯酰胺基十六烷磺酸（ＡＭＣ１６Ｓ）三元共聚物，借助红外光谱和差热分析测定了基结构和热稳定性，初步评价了共聚物的溶液性能，结果表明：ＡＭ／ＡＭＰＳ／ＡＭＣ１６Ｓ共聚物热稳定性好，耐温抗盐能力强。     

6，7-二氢-5H-环戊烷并[b]吡啶

6,7-二氢-5H-环戊烷并[b]吡啶主要用于药物、杀菌剂和抗菌剂的研究,也被广泛应用于制备植物保护剂和合成树脂、防老剂以及塑料制品等。目前因其被作为第四代抗生素头孢匹罗的侧链而成为研究者竞相开发的热点。6,7-二氢-5H-环戊烷并[b]吡啶有实用价值的合成方法主要有N-羟基邻苯二甲酰胺法、丙烯醛法和己二酸二乙酯法。丙烯醛法中6,7-二氢-5H-环戊烷并[b]吡啶的收率为87.4%,具有较好的开发前景。     

Synthesis of poly[(methyl methacrylate)-co-acrylamide] modified by titanium-triisopropoxide and their thermal stability

Poly[(methyl methacrylate)-co-acrylamide] of various compositions were previously prepared by the radical copolymerization reaction of methyl methacrylate and the acrylamide monomer in a solvent. The copolymers were modified through a resonating salt by the addition reaction of a chlorotitanium-triisopropoxide; the modified resins are called Ti hybrid copolymers. The chemical structure of acrylamide side chain groups in the Ti hybrid copolymers was confirmed by the ash weight after combustion, the characteristic absorption band determined by Fourier transform infrared spectrophotometry (IR) and elementary analysis (EA). The curing temperature and time of the resins were determined from the change in the insoluble resin weight when the extraction was done with a mixture of acetone and methanol using the curing resin samples. The thermal stability of the Ti hybrid copolymers was evaluated using both the thermal-degradation temperature (T_x) measured by thermogravimetric analysis and the thermal degradation at 130 °C for 720 h. The cured resins improved the weight loss of the resins at the T_x, and exhibited a high thermal stability.     

Phase morphology and impact toughness of impact polypropylene copolymer

Factors influencing the impact toughness of two impact polypropylene copolymers (IPC) with almost the same ethylene content, molecular weight and molecular weight distribution were studied by temperature gradient extraction fractionation (TGEF), scanning electron microscopy (SEM), nuclear magnetic resonance (NMR) and differential scanning calorimetry (DSC). The results indicate that poor interfacial adhesion between the disperse phase and the continuous matrix, larger dimensions and non-uniform distribution of disperse phases are main reasons for the low impact toughness of IPC B that possesses of a low content of ethylene-propylene segmented copolymer with long crystallizable PE and PP sequences as a compatibilizer between the disperse phase and the matrix.     

刚柔嵌段共聚物聚苯基喹啉-b-聚苯乙烯的合成

利用原子转移自由基聚合合成了端羧基聚苯乙烯,然后与4-氨基苯乙酮反应,生成末端为乙酰基的聚合物,以P2O5为催化剂,将功能化的聚合物与5-乙酰基-2-氨基二苯甲酮共聚,合成出刚柔嵌段共聚物聚苯基喹啉-b-聚苯乙烯(PPO-b-PS),用红外光谱(IR)、氢核磁共振(1HNMR)和热重分析(TGA)对其结构和性能进行了表征,并在三氟乙酸／二氯甲烷混合溶剂中进行了初步的自组装研究。