高度有序多孔氧化铝模板的制备工艺与生长机制的研究

采用二次氧化法制备出高度有序的多孔氧化铝模板，结合扫描电镜和原子力显微镜对其结构、形貌进行观察和表征。研究了铝箔预处理和温度等对多孔氧化铝模板孔洞有序性的影响，讨论了有序孔洞的自组织生长机理。     

氧化锌颗粒膜电阻响应-恢复特性研究

测试了氧化锌颗粒膜电阻响应-恢复特性，讨论了颗粒形态，加热电压、环境气氛、气氛浓度和注入方式等因素对电阻响应-恢复特性的影响。结果表明，随着加热电压的升高，电阻响应-恢复的速度和程度明显加大；断续注入时颗粒膜电阻值的响应随着浓度的增加逐步减弱．     

Effect of fiber types on relevant properties of porous asphalt

The research was conducted to evaluate the effects of cellulose and polyester fibers on the properties of porous asphalt mixes, using the tests of draindown, abrasion, volumetric properties, rutting, and moisture damage. Images of scanning electron microscopy and X-ray computerized tomography were adopted to identify the microstructure of the fiber and inner stone skeleton of porous asphalt. The influence of rutting parameter （G＊/sin δ） of asphalt modified by different fibers on the rutting resistance of the mixes was investigated. Based upon MOHR-COULOMB theory, the cohesion and the angle of internal friction of the mixes were derived from both indirect tension and unconfined compression strength. The experimental results indicate that fibers mainly stabilize asphalt binder and thicken asphalt film around aggregates. Furthermore, they result in the improved mechanical strength of porous asphalt mixes at high temperature slightly. From comparison analysis, cellulose fibers appear to perform better than polyester fibers in porous asphalt mixes.     

Influence of the deposition atmosphere on the characteristics of Pd–Mg thin films prepared by pulsed laser deposition

Bilayered palladium (30 nm thick)–magnesium (350 nm thick) thin films were prepared using the pulsed laser deposition technique in the presence of various background gases (Ar, He and a mixture He + H₂) under different partial pressures (47 and 27 Pa). According to the deposition atmosphere, the Pd/Mg interface shows either a sharp or an extended transition. The electrochemical hydriding properties and the mechanical stability upon cycling of the Pd/Mg film are greatly improved when an extended «intermixing» zone between the Pd and Mg layers is present. The Pd–Mg films prepared under pure helium fulfill these conditions.     

Thin film deposition on a corrugated surface: A molecular dynamics approach

This paper presents the use of molecular dynamics (MD) simulation in the investigation of the surface topography of early-stage film growth on a GMR (giant-magnetoresistance) corrugated structure. The size of the simulated system is limited in order to reduce the computational workload. The numerical model adopts the Morse potential and the Verlet-leapfrog time evolution scheme [R.W. Hockney, 1970; D. Potter, 1972 (Chapter 5). [1]] to describe the atomic interactions which take place between the atoms. The impact energy transferred from the incident atoms to the substrate is modeled by rescaling the atoms within the upper substrate layers. It is found that the important properties of the film-substrate system may be obtained after the deposition of just several atomic layers. The influence of the impact velocity upon the coating parameters is investigated by varying the incident energy of the deposited atoms. The current results indicate that the surface coverage is poor, when atoms are deposited at low incident energies upon a low temperature substrate. At a higher incident energy, the deposited film tends to exhibit a quasi-layer-by-layer growth mechanism, which results in an improved surface coverage. Finally, it is demonstrated that a distinct quasi-fluid behavior is evident on the substrate when the atoms are deposited at high incident energies.     

基于PTFE的PCB的多层层压方法

介绍了采用不同材料类型的粘结膜、半固化片、所需设备和粘结材料,用于生产低到高层数的PTFE多层板的情况。     

Synthesis and characterization of polyaniline films using Fenton reagent

The chemical oxidation of aniline to form polyaniline (PANI) films and powder samples was made using Fenton reagent as an oxidizing agent in aqueous sulfuric acid medium. The PANI films were monitored by using the quartz crystal microbalance and the electronic absorption techniques. The optimum concentration was determined and the results were justified by measuring the UV–vis absorption spectra for the in situ PANI films. The conductivity for the PANI films and powder samples, prepared in different conditions, was measured. Also, the IR spectra, X‐ray and the thermogravimetric analysis for the PANI powder formed in the bulk were measured and compared with the polymer prepared using ammonium peroxydisulfate. A preliminary investigation to the dielectric properties of the polymer powder was measured and discussed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structure and processability of iodinated poly(vinyl alcohol). IV. Drawability of the films iodinated at solution before casting

The drawability of iodinated at solution before casting (IBC) polyvinyl alcohol films prepared by casting aqueous solutions of 10 wt % PVA containing 15.2, 39.8, 83.2, 117.0, and 140.1% was examined with a tensile tester at 20–60°C. The tensile behavior of IBC films showed that the yield and breaking loads were much lower, and the breaking elongation was even higher than those of the unoriented iodinated after casting (IAC) films as well as the untreated PVA films. The maximum draw ratios of the films with the weight gain of 15.2, 39.8, 83.2, 117, and 140.1% were 4.5, 5.5, 8.5, 8.0, and 7.5, respectively, which were achieved at 20°C in all. The crystallinity of all films increased by the maximum draw, regardless of crystallinity before drawing. The crystalline structure was recovered to the original PVA crystalline lattice by deiodination. Amorphous orientation and initial moduli increased with the maximum draw ratio, while the orientation of crystals was constant. The orientation and moduli increased up to the weight gain of 83.2%, whose highest draw ratio and initial modulus were 8.5 and of 7.1 GPa, respectively, and then decreased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

二次电池电极基板用复合多孔金属材料的研究

介绍了一种复合金属多孔体的制备及其方法，首先以泡沫塑料为芯膜，经过导电化处理使其具有导电性，其次进行电沉积金属铁，再进行电沉积金属镍，经过热处理后可制备出复合金属多孔体。该复合金属多孔体用铁取代金属镍，其抗拉性能优于单质泡沫镍，同时可以降低制造成本，主要用于载体如电池电极。