部分可渗透直立圆柱的消波作用研究

本文导出了线性波浪作用于上部可渗透的直立刚性圆柱体上的水动力的解析解。在线性有势流的假定下，用特征函数展开方法求出了内部和外部流场的解。给出了不同波浪要素及结构尺寸参数下的数值结果。由结果可知，提高可渗透性可以有效消减波幅。     

Pad effects on material-removal rate in chemical-mechanical planarization

The role of a porous pad in controlling material-removal rate (MRR) during the chemical-mechanical planarization (CMP) process has been studied numerically. The numerical results are used to develop a phenomenological model that correlates the forces on each individual abrasive particle to the applied nominal pressure. The model provides a physical explanation for the experimentally observed domains of pressure-dependent MRR, where the pad deformation controls the load sharing between active-abrasive particles and direct pad-wafer contact. The predicted correlations between MRR and slurry characteristics, i.e., particle size and concentration, are in agreement with experimentally measured trends reported by Ouma¹ and Izumitani.²     

Forecasting Capillary Characteristics for Aluminum Nitride Ceramic ― Liquid Metal Systems

A test has been devised that allows one to determine the work of adhesion and wettability in a system composed of aluminum nitride ceramics with a liquid metal without the need for experimental examination. A correlation is examined between the work of adhesion on the one hand and that criteria or others on the other that have been proposed by various researchers. Forecasts are made for the work of adhesion and wetting angle for a series of metals that have not been examined previously. An experimental check has been made on the forecast adhesion activity for some elements.     

TiB2与BN复相陶瓷的渗流模型

试验结果证实,TiB₂与BN复相陶瓷的导电性能符合渗流理论,原料粉粒度配比下,其渗流阀值为V_c%=22.9%;原料粉粒度比的改变将改变渗流阀值,从而改变各配比下的电阻率值;TiB₂与BN在SPS系统中快速烧结,晶粒的尺度比与原料粉的粒度比基本保持一致。     

工艺条件对薄片陶瓷材料凝胶流延成型的影响

利用有机单体的聚合原理，成功进行了陶瓷薄片材料的凝胶流延成型。讨论了工艺条件对成型的影响。使用惰性气氛保护克服了单体聚合反应中的氧气阻聚问题，浆料在一定温度和气氛条件下能够顺利完成聚合反应。所成型的坯体具有良好的强度和柔韧性，在1550℃经2h烧结，烧结样品显微结构均匀，没有发现晶粒异常长大现象，烧结体致密度达到97．7％。     

金属PTC陶瓷复合材料结构及其导电机理

研究了金属ＰＴＣ陶瓷复合材料的电学性能和其材料组分。结果表明，掺入金属的ＰＴＣ陶瓷材料经氮气中烧结，然后在空气中进行热处理，材料表面形成高势垒层，金属ＰＴＣ陶瓷复合材料的室温电阻较ＰＴＣ的陶瓷高。样品之中存在大量不同类型的极化，在低温时样品电阻较高，温度增加后，大量各种类型离子极化出现，在变价金属铁的变价导电作用下，削弱表面势垒，使金属ＰＴＣ陶瓷复合材料电阻降低，表现出ＮＴＣ现象。在电场作用下，正负电荷、晶粒畸变和空位缺陷等产生空间电荷极化使金属ＰＴＣ陶瓷复合材料有较高介电常数。介电损耗（ｔｇδ）频谱和介电δ温度谱上都出现一个介电峰，其主要原因是跃迁极化，金属阳离子由一个位置跃迁到另一个位置，在介电损耗所对应的频率和温度时出现跃迁极化率最大     

热释电系数的测量方法

描述热释电系数的两种测量方法。其一为电荷积分法，测试系统简单，测量数据准确，且能满足零电场条件下的测量。其二为动态电流法，采用调制热源技术，研究在特定温度条件下热释电材料的动态热释电响应。     

电致伸缩陶瓷微位移器非线性的数值方法补偿

本文通过对电致伸缩陶瓷材料的非线性进行分析。找到了补偿电致伸缩陶瓷非线性的数值方法，并对不同回程大小的电滞回线进行了分段处理，使补偿结果更为精确。     

发泡金属的开发、性质及应用(Ⅰ)──发泡金属的制备方法

系统地综述了发泡金属的生产方法，包括铸造法、粉末冶金法、烧结法、沉积法和高压浸透法等。介绍了各种方法的特点及适用范围，指出了它们的优缺点及相应的改进措施，并对今后的发展方向提出了建议。     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.