合金钢连铸机生产工艺分析及实践

对新钢特殊钢有限责任公司整个合金钢连铸机的生产工艺进行了分析，提出了提高钢水质量和优化连铸工艺参数的有效措施，使铸坯的质量得到了有效控制和改善。     

�����������������������������ܿ��������о�

白马庙气田蓬莱镇气藏储层致密 ,孔隙结构复杂 ,非均质性强 ,单井产能低 ,研究储层特征和受控因素 ,加强储层改造方是气藏效益开发的出路。储层精细研究揭示 ,气井产能受沉积相和构造条件控制 ;高、中产井与大而厚、物性好的河口坝、河道砂坝沉积微相有关 ,纵向上具很强的层段性 ,主产层集中在Ⅳ～③、Ⅲ～③两套砂组 ,其钻探成功率分别达 82 %和 10 0 % ;平面上多分布于主体构造和东南鼻状突起 ,二者高、中产能井分别占 30 %和 70 %。在深入的地质研究和储层压裂评层选井的基础上 ,采用多层打开、分层压裂、多层合采的方法可提高气井产能 ,并形成了一套行之有效的压裂评层选井的综合配套技术。采用该技术优选出 19口井 ,已实施 5口井全获成功 ,气产量成倍或十几倍增加 ,其中白浅 4 5井气无阻流量高达 18× 10 4m3 /d ,白浅 38井投产 16 5d净增产值 10 0余万元     

Filtration of Non-Newtonian Hydrocarbon Fluid in a High-Frequency Electromagnetic Field

The paper gives the results of experimental investigations of the initial pressure gradient of bituminous oil and the time dependences of variation of the temperature in a formation model and of the well production rate in a microwave-frequency electromagnetic field. The effect of strong decay of the non-Newtonian properties of bituminous oil is revealed. The nonuniformity of temperature distribution over the formation thickness is demonstrated, which depends on the initial production rate of the well and on the duration of stimulation of the bottom-hole zone of formation.     

膜分离技术在水处理领域的应用

对2000年底巴黎“饮用水和工业用水制造领域中的膜技术”国际会议进行了简单的回顾，根据会议经历对当今膜分离技术在水处理领域的应用市场进行分析，提出今后液体膜分离技术的研究和发展的重点。最后对我国液体分离膜技术的发展提出一些建议。     

也谈防水卷材生产的设备与工艺

介绍了防水卷材生产设备设计和操作的工艺参数，以及配套系统的配置依据，由此制造出的成套设备可生产出各规格的达标产品。     

The complexity of economic equilibria for house allocation markets

We prove NP-completeness of deciding the existence of an economic equilibrium in so-called house allocation markets. House allocation markets are markets with indivisible goods in which every agent holds exactly one copy of some good.     

鞍钢现有人造富矿产能及1600万t/a生铁规模的合理炉料结构的探讨

简要介绍了鞍钢现有人造富矿生产能力，分析了鞍钢生产1600万t／a生铁所需要的炉料数量、品种和质量，并提出了解决炉料缺口的方法和措施。     

硫酸盐浆厂污水处理工程及单元技术特点

本文简略介绍云南某硫酸盐浆厂污水处理工程采用的国内不多见的污水单元技术，并对其先进性和实用性效果进行评价和探讨。     

油管电热清防蜡技术在强水敏油田的应用

江苏油田的庄 2、韦 2油田属强水敏油田 ,采用热 (水 )洗油井和化学清防蜡效果较差 ,两油田每年因洗井造成地层污染影响的产量损失在 5 0 0 0t以上 ,约占油田产量的 4 5 %。根据集肤效应 ,采用油管电热清蜡技术 ,在含水小于 6 0 %、井斜小于 4 0°的油井上可正常使用 ,一般通电加热 4 0～ 80min后 ,油井井口温度能达到 5 0℃左右 ,最高可达到 6 5℃以上 ,连续加热 5～ 6h即可达到清蜡目的 ,电热清蜡为周期 6 0～ 90d。影响电热清蜡主要指标因素是油井的产液量 ,产液量越小 ,所需要的加热电流和加热电压也越小 ,井口温度达到最高值越低 ,清蜡效果越差。试验的 7口井平均年度投入产出比达到 1∶5 ,经济效益和社会效益十分明显。     

Production of hydrogen over bimetallic Pt–Ni/δ-Al2O3: I. Indirect partial oxidation of propane

Indirect partial oxidation (IPOX) of propane was studied over bimetallic 0.2 wt.% Pt–15 wt.% Ni/δ-Al₂O₃ catalyst in the 623–743 K temperature range. The unreduced and reduced forms of the catalyst were characterized by ESEM–EDAX and X-ray diffraction (XRD). In the IPOX tests, the effects of steam to carbon ratio (S/C), carbon to oxygen ratio (C/O₂) and residence time (W/F (g_cat h/mol HC)) on the hydrogen production activity, selectivity and product distribution were studied in detail. The effect of temperature program applied (increasing from 623 to 743 K, ITP; decreasing from 743 to 623 K, DTP) during reaction was also tested. The results showed that the Pt–Ni bimetallic system has superior performance characteristics compared to the monometallic catalysts reported in literature. The reason is thought to be the utilization of the catalyst particles as micro heat exchangers during IPOX; the heat generated by Pt sites during exothermic total oxidation (TOX) being readily transferred through the catalyst particles acting as micro heat exchangers to the Ni sites, which promote endothermic steam reforming (SR). The optimal conditions were found as S/C = 3, C/O₂ = 2.70 and W/F = 0.51 g_cat h/mol HC for IPOX of propane on the basis of high hydrogen productivity and selectivity between 623 and 748 K for the experimental conditions tested. The thermo-neutral points obtained showed the sustainability of reaction in terms of energy.