Corrosion resistance of Al–Cr-slag containing chromium–corundum refractories to slags with different basicity

Al–Cr slag is the solid waste generated by the smelting of Cr metal. It presents a range of environmental hazards. This study addressed the corrosion resistance of Al–Cr slag containing chromium–corundum refractories to slags with different basicity. Herein, we provide suggestions for the use of Cr–corundum of different basicity in kilns. Al–Cr slag, brown fused Al₂O₃, and chrome green were used as the raw materials, with pure calcium aluminate cement being used as a binder. The brick samples, prepared using different blends of chrome green and corundum, were fired at 1600?°C, and subsequently subjected to a slag corrosion test. After corrosion by slag of different basicity, the phase composition and microstructure of the sample were analyzed by X-ray diffraction, energy dispersive spectrometer and scanning electron microscopy. There were two major findings. First, Cr–corundum brick made from Al–Cr slag has a better slag corrosion resistance than that made from Cr₂O₃ and brown fused Al₂O₃. Second, Cr–corundum brick made from Al–Cr slag has superior corrosion resistance to slag with a CaO:SiO₂ ratio of 2:1.     

A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.     

Formation of a protective layer against corrosion on Mg alloy via alkali pretreatment followed by vanillic acid treatment

Although Mg alloy possesses high specific strength, low density, and good biocompatibility, poor corrosion resistance hinders its further applications. In the present study, an innovative protective layer against corrosion was prepared on the AZ31 Mg alloy via alkali pretreatment followed by vanillic acid treatment. The alkali pretreatment supplied –OH for the AZ31 Mg alloy surface to react with vanillic acid. The vanillic acid treatment played a crucial role in enhancing the corrosion resistance due to the excellent ability to act as a barrier and retard aqueous solution penetration, which effectively isolated the underlying Mg alloy from the corrosive environment. The corrosion current density of alkali and vanillic acid-treated Mg alloy (AZ31V) almost showed two orders of magnitude lower values in comparison with that of the AZ31 Mg alloy, and the corrosion potential of AZ31V Mg alloy increased from −1.41 to −1.25 V. The immersion tests proved that there was no occurrence of severe corrosion. Hence, the alkali pretreatment and vanillic acid treatment may represent a promising method to improve the corrosion resistance of Mg alloy.     

某油田油井采出水腐蚀因素研究

我国油田油井生产中采油井管柱腐蚀现象十分普遍,所以在注CO_2驱进行开采过程中要进行采出水的质量分析。对现阶段的油田生产腐蚀及防腐技术进行论述,提出相对应的防腐措施,进一步为油田生产作业提高产量。     

Corrosion behavior of Cu–Sn bronze alloys in simulated archeological soil media

The corrosion behavior of synthetic Cu–Sn bronze alloys with six different Sn contents was examined through an electrochemical test and a synthetic test in a simulated corrosive medium. The mechanism of corrosion and the morphology of the corroded surfaces were characterized through field emission scanning electron microscopy equipped with energy-dispersive spectroscopy. At the corrosion potential, the corrosion behavior appears to be determined by the charge transfer step and the diffusion process. It was found that the bronze-IV (Cu–26.8Sn) specimen exhibited the best corrosion resistance, as evidenced by a low corrosion current density and a high impedance. This improvement resulted from an increase in the content of the Cu–Sn solid solution in the alloy, which was conducive to forming a relatively more protective passive film on the surface of the bronze alloy. This finding would be valuable in the anticorrosion protection of archeological artefacts after their excavation.     

膨胀剂对约束条件下UHPC早期抗裂性能影响的试验研究

超高性能混凝土(UHPC)在钢桥面铺装结构中由于铺装材料受到钢板、栓钉等的约束,加上材料本身水胶比小,更易收缩,早期容易承受拉应力导致开裂。通过在拌和过程中添加膨胀剂可以起到减小收缩的作用,但该方法对于约束条件下的UHPC铺装的早期抗裂性能提升是否有促进作用,仍需通过更多试验进行合理评估和深入研究。通过圆环法对3组不同配方的UHPC在均匀约束条件下的早期抗裂性能进行定量测试,并将试验数据进行回归分析和计算,得到了各组的平均应力发展速率,进而评估了各组的开裂风险等级。试验结果表明,通过在UHPC中加入适量膨胀剂,可使其最终收缩应力减小,并可降低其收缩应力发展速率,进一步降低其在约束条件下的开裂风险。     

Corrosion behaviour of AA2024 aluminium alloy in different tempers in NaCl solution and with the CeCl3 corrosion inhibitor

The paper analyses the corrosion behaviour of naturally and artificially aged AA2024 alloy in NaCl solution and in the presence of an environment-friendly corrosion inhibitor, CeCl₃. On the basis of the values of polarisation resistance and corrosion current density, the corrosion resistance of the protective inhibitor film is established as well as the general corrosion resistance of this aluminium alloy. Resistance to pit formation is determined based on the difference in pitting and corrosion potentials while resistance to pit growth is determined based on the amount of charge consumed during pit growth. A scanning electron microscope is used to examine the morphology of the pits formed during the pitting corrosion testing, as well as to determine the cerium content on intermetallic particles and the matrix AA2024 alloy. The corrosion behaviour of AA2024 alloy is investigated after different test periods in NaCl solution and in the same solution with the CeCl₃ inhibitor. The corrosion resistance of both tempers of AA2024 alloy is more than one order of magnitude higher in the presence of CeCl₃. An explanation of the observed differences in the corrosion behaviour of the naturally and artificially aged AA2024 alloy is proposed. Different corrosion behaviour of the alloy after different test periods is also explained.     

Significant population genetic structuring in Rhyzopertha dominica across Turkey: Biogeographic and practical implications

Rhyzopertha dominica is a key pest of stored grain. Understanding the movement of this beetle on broad geographic scales is crucial, particularly when developing strategies to prevent the spread of phosphine resistance. We assessed population genetic structuring in this pest across Turkey, using a combination of mitochondrial (cytochrome oxidase I) and microsatellite markers. In addition, we screened samples for Wolbachia, as this endosymbiont has previously been suggested to be associated with low mitochondrial genetic diversity in this beetle. Mitochondrial genetic diversity was low, with only six haplotypes identified. The genetic diversity was, however, substantially higher than that previously found in Australia or India, suggesting that R. dominica may have originated in the Middle East. Wolbachia were detected only at a single site, indicating they are not impacting the mitochondrial genetic diversity of R. dominica across Turkey. Microsatellite markers indicated there is significant geographic genetic structuring across Turkey, even among sites less than 100 km apart, suggesting there is little movement of beetles across regions within the country. This contrasts with the significantly higher levels of gene-flow found in Australia and the United States. We suggest that the limited movement of beetles across Turkey may be due to a combination of the historically localised agricultural practices (which limits anthropogenic movement among regions), and the mountainous landscape (which limits active flight among regions). Our results demonstrate that the movement of stored product pests may differ significantly across studies conducted in different countries. As a consequence, phosphine resistance management strategies must incorporate region specific information on the extent of beetle movement.     

氧气底吹熔炼氧枪浅析

系统地论述了氧气底吹熔炼氧枪的结构、工作原理、设计计算方法、材质及蚀损机理．指出了延长氧枪使用寿命的措施。