An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

降低气体悬浮焙烧炉焙烧过程中Al_2O_3粒度破损的措施

为了降低气体悬浮焙烧炉焙烧过程中Al_2O_3粒度的破损,对气体悬浮焙烧炉焙烧过程中氧化铝粒度的影响因素进行了分析,提出了降低粒度破损的一些措施。     

Effect of gas mixing ratio on gas-phase composition and etch rate in an inductively coupled CF4/Ar plasma

In this work, we carried out investigations aimed at understanding the effect of gas mixing ratio on plasma parameters, gas phase composition and etch rate in CF₄/Ar inductively coupled plasma. For this purpose, a combination of experimental methods and modelling was used. Experiments showed that electron temperature and electron density are not very sensitive to variations of Ar content in CF₄/Ar plasma. From a zero-dimensional plasma model, the densities of both neutral and charged particles change monotonically. The analysis of surface kinetics based on an ion-assisted etching mechanism showed the possibility of non-monotonic etch rate behaviour due to a concurrence of chemical and physical etching pathways.     

Filtration of Non-Newtonian Hydrocarbon Fluid in a High-Frequency Electromagnetic Field

The paper gives the results of experimental investigations of the initial pressure gradient of bituminous oil and the time dependences of variation of the temperature in a formation model and of the well production rate in a microwave-frequency electromagnetic field. The effect of strong decay of the non-Newtonian properties of bituminous oil is revealed. The nonuniformity of temperature distribution over the formation thickness is demonstrated, which depends on the initial production rate of the well and on the duration of stimulation of the bottom-hole zone of formation.     

黑岱沟露天矿重型汽车预防性维修的探讨

通过对黑岱沟露天煤矿运输设备出动率调查,初步分析了目前主要运输设备的现状以及存在问题的原因和影响因素,就加大预防性维修的比重,实行全面的预防性维修制度提出了一些看法。     

东方N-18250-2型凝汽器胶球清洗系统改造

对湘潭电厂存在已久的胶球清洗装置收球率低的问题进行了深入探讨，结合电厂对胶球清洗系统的改造、试验过程，分析并提出了影响胶球清洗装置清洗效果及收球率的诸多原因及其解决方法。     

德国联邦物理技术研究院(PTB)气体微流量计量评介

在真空技术应用中 ,高精度气体微流量计用于连续膨胀法校准系统压力的产生、漏孔漏率的测量以及真空泵抽速的测定。PTB先后研制了三代气体微流量计 ,第一代为手动型 ,第二代为半自动型 ,第三代为全自动型。本文详细介绍了PTB研制的气体微流量计的性能和特点 ,并介绍了气体微流量计在真空漏孔的漏率测量方面的应用。另外 ,还介绍了PTB最近研制的大气压力下漏孔漏率测量系统的性能和特点     

难处理金矿石加石灰焙烧焙砂中CaS的消除

介绍了用空气氧化预浸加石灰焙烧焙砂中的CaS，以消除其对金氰化的影响。预浸后金的氰化浸出率可从58％提高到80％以上。     

高效率平面磁控溅射器的研制

介绍一种新型磁控溅射装置。它采用两块极性相对的环状磁铁的设计方法，通过扩大靶表面的等离子放电区域面积，使传统磁控溅射枪使用中经常受到的两个限制──溅射速率与靶的利用率得到了较大的改善。实验中铜靶在溅射功率密度为11W／cm~2时溅射速率约为800nm／min，如果继续提高功率则可获得更高的速率。而靶的利用率可达64％左右。另外，在认为出射粒子符合cos~nθ分布的前提下，发现当n＝3．3时，实验数据和理论数据符合得较好。