CSTN-LCD用铬版清洗效果的改善

利用铬版清洗机对CSTN-LCD用铬版进行清洗处理,分析了清洗过程中出现的铬层脱落现象,铬层脱落与轴向喷射压力和水平切力密切相关,通过调整转速和喷射压力探索了安全使用条件:在转速不超过1000r/min,喷射压力低于0.5×105Pa的情况下使用铬版清洗机进行清洗是相对安全的。同时采用预清洗处理的方法满足清洁要求,使换线时间由平均3h缩短到平均1h以内,年产能提高270000片。     

Quality of Service in VoIP Communication

The focus of this paper lies in the practical aspects of voice over IP communication. VoIP configurations in the H.323 standard will be presented briefly. Following that, the fundamental protocol procedure of H.323 communication will be briefly explained. A further part of the paper will address the subject QoS (quality of service), and present the common measurement methods used in QoS. Results gained from experiments conducted in a VoIP environment will then follow. The investigations concentrate primarily on the load behavior of voice packets in relation to important parameters of this service. The results obtained are presented and evaluated in diagrams. The paper concludes with a summary.     

Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Mean residence time of gas in mechanically agitated gas–liquid contactors

In the present study of gas–liquid contactors, mean residence/contact time was calculated from knowledge of superficial velocity and the gas phase hold-up, for various gas rates and impeller geometry and speeds, and compared with values obtained from RTD measurements. A new correlation, involving Flow Number, Froude Number, system geometry and the physical properties, is proposed. This uses the authors data and those available in literature.     

在经典极限下量子斯特林制冷机的优化

经济利润率是评价一个实际热力装置的主要指标之一。将有限时间热力学，非平衡量子统计理论和yong经济学相结合，导出了量子斯特林制冷机的最大利润率以及对应的性能界限，其结果与实际斯特林制冷机的优化设计和模型评估提供了一个最佳的预选方案。     

Driver detection and recognition of lineside signals and signs at different approach speeds

A study was carried out using simulation to investigate driver responses to lineside signals and signs at various approach speeds. The objectives of the study were: (1) to find out whether train speed would significantly affect signal/sign reading; (2) to examine at which point certain types of signs or signals could be detected or recognised, and (3) to determine a speed cut-off level above which certain types of signs or signals are no longer recognisable or detectable. Fifty-seven train drivers from 12 Train Operating Companies in the UK participated in the trials. Twenty different types of lineside signs and ten types of signals were tested under six different approach speeds ranging from 100 to 350 km/h (62–218 mph). Driver performance measures were ‘time remaining to the signal/sign’ at the point of detection or recognition, and reading error rate. The results showed a significant influence of train speed on driver responses to lineside signals/signs and demonstrated a non-linear relationship between driver responses to signals/signs and approach speed. This has been used to estimate a maximum approach speed limit within which a specific signal or sign can be correctly detected or recognised. The findings and implications of the study are discussed in the paper.     

石油测井仪器可靠性指标探讨

在分析常用可靠性指标及其应用现状的基础上，根据可靠性理论及石油测井仪器的特点。提出了石油测井仪器的可靠性模型。在探讨常用可靠性指标对石油测井仪器适用性的同时，提出将平衡稳定工作时间NWTURE和免维修测井井次NOLWNM作为石油测井仪器可靠性指标的思想；探讨了获取可靠性指标的途径。给出了推荐使用的石油测井仪器可靠性指标。     

Spare parts inventory management with demand lead times and rationing

We study an inventory system that consists of two demand classes. The orders in the first class need to be satisfied immediately, whereas the orders in the second class are to be filled in a given demand lead time. The two classes are also of different criticality. For this system, we propose a policy that rations the non-critical orders. Under a one-for-one replenishment policy with backordering and for Poisson demand arrivals for both classes, we first derive expressions for the service levels of both classes. The service level for the critical class is an approximation, whereas the service level for the non-critical class is exact. We then conduct a computational study to show that our approximation works reasonably, the benefits of rationing can be substantial, and the incorporation of demand lead time provides more value when the demand class with demand lead time is the critical class. The research is motivated by the spare parts service system of a major capital equipment manufacturer that faces two types of demand. For this company, the critical down orders need to be satisfied immediately, while the less critical maintenance orders can be satisfied after a fixed demand lead time. We conduct a case study with 64 representative parts and show that significant savings (as much as 14% on inventory on hand) are possible through incorporation of demand lead times and rationing.     

The Gas-to-Particle Heat Transfer and Hydrodynamics in Spouted Bed Drying of Sawdust

This article presents experimental results for spouted bed drying of sawdust, carried out in a full-scale as well as in a laboratory-scale dryer using air as well as steam as drying media. The aim is to present design parameters for a spouted-bed sawdust dryer that can be used by the industry in designing full-scale dryers. A hydrodynamically stable spouted jet spouted bed was obtained. The heat transfer characteristics of the bed were represented in terms of a volumetric heat transfer coefficient (VHC). When sawdust is dried in a spouted bed, the mean VHC is increasing up to fiber saturation level (20-25% wb) from 40 to 110 W/m³ K. The VHC decreases with the residence time and with an increased static bed height. Gas temperature profiles are also presented for the bottom part of the drying chamber.