Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

焚烧炉控制系统

化工废气、废液焚烧炉是一种常用的环保处理装置，就其工艺详细介绍焚烧炉燃烧过程的控制及其安全联锁措施。     

厚度控制技术在中厚板轧制生产中的应用

本文探讨了影响中厚板厚度波动的因素，结合安钢中板厂2800mm轧机按合同轧制一批交货重量不大于理论重量船板的生产实践，总结了实际生产中实现高精度厚度控制的有效方法。     

Ideal-gas thermodynamic properties for natural-gas applications

Calculating caloric properties from a thermal equation of state requires information such as isobaric heat capacities in the ideal-gas state as a function of temperature. In this work, values for the parameters of thec _p ⁰ correlation proposed by Aly and Lee were newly determined for 21 pure gases which are compounds of natural gas mixtures. The values of the parameters were adjusted to selectedc _p ⁰ data calculated from spectroscopic data for temperatures ranging from 10 to 1000 K. The data sources used are discussed and compared with literature data deduced from theoretic models and caloric measurements. The parameters presented will be applied in a current GERG project for evaluating equations of state (e.g., the AGA 8 equation) for their suitability for calculating caloric properties.     

�¸�������в������Ȼ�����꾮�ٶȵ�;��

本文针对天然气井提高钻井速度问题,总结分析了盆地中部井身结构,水力、机械参数,聚合物钻井液,正注反挤固井等工艺技术对该地区钻速的影响。指出提高天然气井钻井速度,必须搞好系统工程,形成配套技术。     

代数应力模式的分析解及其在充分发展旋转管流中的应用

本文通过求解雷诺应力在代数应力模式中与平均速度梯度之间的分析关系，研究了代数应力模式在涡旋流动特别是在充分发展旋转管流中存在的内在缺陷，这些缺陷的主要表现为：（１）在不考虑固壁对湍流影响的代数应力模式中，分析解给出Ｗ∝ｒ和ｖｗ＝０的错误结论；（２）若在代数应力模式中考虑固壁对湍流影响，在对称轴上会有ｖ＾２不等于ｗ＾２的非物理解。与诺应力输运模式相比，代数应力模式的缺陷归限结底在于该模式的基本假设不     

Study on Factors Affecting the Structure of High SpeedSteel Ingot Produced by ESR

ＳｔｕｄｙｏｎＦａｃｔｏｒｓＡｆｆｅｃｔｉｎｇｔｈｅＳｔｒｕｃｔｕｒｅｏｆＨｉｇｈＳｐｅｅｄＳｔｅｅｌＩｎｇｏｔＰｒｏｄｕｃｅｄｂｙＥＳＲＬｉＺｈｅｎｇｂａｎｇ；ＣｈｅＸｉａｎｇｑｉａｎＡｂｓｔｒａｃｔ：Ｔｈｅｉｎｆｌｕｅｎｃｅｏｆｔｈｅｍｅｔａｌｐ...     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

关于供排水管网的水力计算和校核

以往对电站技术供排水系统大都未进行水力平差计算，致使一些实际电站的供排水系统达不到预期的效果，甚至影响机组的正常运行。据此，给出了供排水管网的平差计算方法，有利于正确评估电站管网，另外，提出了管网校核应注意的问题。