Effects of genotype and treatment on the antioxidant activity of sweet potato in Taiwan

Six genotypes of sweet potato commercially available in Taiwan, including TNG57, TNG66, TNG68, TYY1, RP and WP, were used as samples in this study of the effects of steaming and kneading with pre-steaming treatments on the antioxidant components and antioxidant properties of methanolic extracts. Steam treatment increased the total phenols contents of all genotypes (2–13 times), flavonoids content of RP (1.3 times) and anthocyanins contents of RP and WP (5–6 times). Steam treatment also increased the reducing power and scavenging DPPH radical effect of sweet potato flours. For the methanolic extracts of steamed and kneaded flours, reducing powers were 0.02–1.70 at 5.0 mg ml⁻¹ and the scavenging effects on DPPH radicals were 19–92% at 2.5 mg ml⁻¹. Both showed the order of RP > WP > TYY1 and TNG66 > TNG57 and TNG68. However, the chelating effect of the six genotypes at 1.0 mg ml⁻¹ ranged from 50% to 73%. Contents of total phenols, flavonoids, and anthocyanins of sweet potato flours were significantly positively correlated with the reducing power and scavenging DPPH radical effects. After steaming and kneading treatments, RP showed the highest increase in the contents of total phenols, flavonoids and anthocyanins among the six genotypes studied.     

积层板的制造方法

概述了积层板的开发背景、制造工艺和最近的开发动向。     

非线性扩频序列的三项式特性

讨论了三类非线性扩频序列(GMW序列、No序列和Kasami序列)的三项式特性，利用这三类序列的迹表示，证明了GMW序列、No序列和Kasami序列均具有正则三项式对。     

Effect of Stoichiometry on Properties of Rare-Earth-Based Hydrogen Storage Alloy for Nickel-Metal Hydride Secondary Battery

Effect of stoichiometry on microstructures, electrochemical properties and PCT characteristics of the alloys MI(Ni0.71Co0.15-Al0.06Mn0.08)x (MI=Lanthanum-rich Michmetal, x=4.6~5.2) have been investigated. The lattice constants a, c, and cellvolumes of non-stoichiometric alloys are bigger than those of the stoichiometric alloy. With the increasing stoichiometry x,the value of a decreases, and the value of c and cell volume increases except for those of the stoichiometric alloy; the plateaupressure of PCT curve, discharge capacity and cycling stability all increase. The alloy with x=5.2 shows the highest dischargecapacity and the best cycling stability among the studied alloys.     

泌阳凹陷新庄辫状三角洲沉积体系及储集性能

依据岩心和测井资料，对泌阳凹陷新庄辫状三角洲沉积体系进行了沉积微相划分和微相特征分析。在此基础上，进行了沉积模式和油气储集性能的研究。研究认为，水下分流河道、河口砂坝是该区最好的油气储集体，其它微相依次为辫状河道、浊积岩、前缘席状砂和决口扇。研究结果可为下一步的滚动勘探提供地质依据。     

Investigation into polishing process of CVD diamond films

A new technique used for polishing chemical vapor deposition (CVD) diamond films has been investigated, by which rough polishing of the CVD diamond films can be achieved efficiently. A CVD diamond film is coated with a thin layer of electrically conductive material in advance, and then electro-discharge machining (EDM) is used to machine the coated surface. As a result, peaks on the surface of the diamond film are removed rapidly. During machining, graphitization of diamond enables the EDM process to continue. The single pulse discharge shows that the material of the coated layer evidently affects removal behavior of the CVD diamond films. Compared with the machining of ordinary metal materials, the process of EDM CVD diamond films possesses a quite different characteristic. The removal mechanism of the CVD diamond films is discussed.     

工艺参数对纳米颗粒Cu/SiO_2复合薄膜结构和光谱特性的影响

用离子束溅射法制备了具有反常光吸收特性的纳米颗粒CU／SiO2复合薄膜。获得了在离子来参数一定时，基片温度、膜料的沉积时间和镀膜后的保温时间等工艺参数对这种薄膜结构和光学特性的影响规律，并对纳米颗粒Cu／SiO2复合薄膜的反常光吸收特性作了计算和解释。     

烧结NdFeB合金中的夹杂物

使用金相显微镜、扫描电镜及Ｘ射线能谱和波谱观察并分析了ＮｄＦｅＢ烧结材料中夹杂物的形态、数量和组成。磁粉制备后立即烧结的ＮｄＦｅＢ磁体中的夹杂物是氧化钕；而在不同环境条件下放置后的ＮｄＦｅＢ粉再烧结的材料中发现，除了氧化钕的夹杂物外，还有钕的氮化物及钕的氮氧复合夹杂物。同时还论讨了这些夹杂物对于ＮｄＦｅＢ材料磁性能的影响。     

烧结工艺对液相合成（SrPb）TiO3基陶瓷热敏特性影响的研究

本文在液相合成（ＳｒＰｂ）ＴｉＯ３粉的基础上，研究了升温速率、保温时间、烧结温度及降温方式对（ＳｒＰｂ）ＴｉＯ３基陶瓷的Ｖ型ＰＴＣ热敏特性的影响。实验表明：升温速率对其热敏特性影响不大，保温时间和烧结温度的作用是一致的，具有一最佳范围。而降浊方式对材料的热敏特性影响较大。综合各因素的影响，本配方中，样品的烧结制度定为：以２００℃／ｈ的速率升温，在１２５０℃保温１ｈ，炉冷至９５０℃，保温０．５ｈ，再     

PP／SiO2／SBS共混复合材料性能的研究

通过加入增强剂、增韧剂、抗氧剂等添国剂可改善聚丙烯力学性能。以ＳｉＯ２为填料，丁苯橡胶（ＳＢＳ）为增韧剂，探讨ＳｉＯ２、丁苯橡胶含量对共混体系强度、韧性的影响，结果表明，在ＳＢＳ含量大于５％、ＳｉＯ２一小于１０％的范围内，可使ＰＰ／ＳｉＯ２／ＳＢＳ复合的拉伸弹性模量和冲击强度明显提高，其力学性能均为均衡。