基于移动Agent技术的QoS保障机制

介绍了移动Agent的基本特性。移动Agent可在异构的网络各个节点间自由地移动,它能感知网络的状态,监控系统并与其他Agent进行交互。IETF的IS模型采用了RSVP(ResourcereSerVationProtocol)协议对系统资源进行预留,从而达到一定程度上保障所需QoS的目的。QoS保障机制将移动agent技术与RSVP协议结合起来,通过资源预留和agent动态移动的实现可以达到更好地改善QoS的目的。     

双马来酰亚胺树脂体系的固化反应研究

利用ＤＳＣ及原位ＦＴＩＲ技术研究了双马来酰亚妥树脂体系的固化反应，获得了在固化反应过程中各组分的转化率与时间的关系，结合热分析数据，确立了最佳固化工艺。     

黑钨矿细泥浮选时有机螯合剂的活化作用

黑钨矿细泥的有效浮选仍是有待解决的选矿难题。本文试图采用有机螯合剂作活化剂，以实现黑钨细泥浮选药剂低耗高效的目的。     

稀土在搪瓷面釉上应用的研究

采用稀土氧化物和无机化合物的复合物（不简称ＲＩ－复合物）作为搪瓷釉浆悬浮剂，使之全部或大部分代替粘土，进行了一系列试验，已获得成功，突破了长期来搪瓷工业离不开粘土的传统工艺，并实现了工业化生产。     

The combined effects of curing and environmental exposure on fracture properties of woven carbon/epoxy laminates

This paper concerns a study of the combined effects of curing conditions and environmental exposure on the ultimate properties of two commercial woven carbon/epoxy laminates. Curing parameters (heating rate and applied pressure) were varied so as to obtain six different conditions for each material. Moisture saturation was also achieved by exposing some of the cured samples to environmental conditions of 70°C and 95% relative humidity. Four different tests (tensile, impact, Mode I and Mode II interlaminar fracture resistance) were therefore performed, and the results obtained on the different materials before and after moisture saturation compared. Neither curing pressure nor heating rate nor moisture absorption were observed to have any practical effect on tensile and impact properties. On the contrary, one noticeable effect was the interlaminar fracture resistance of the laminates. The results are discussed and interpreted in terms of damage formation and stress intensification mechanisms.     

改性玻纤增强尼龙610,1010塑料

研究了采用(准)中粘度级尼龙做基体树脂,加入成核剂改善尼龙的结晶过程,提高结晶速率和初始熔融温度;添加光、热氧稳定剂,防止尼龙在成型加工和使用过程中产生降解与老化,提高塑料制品的质量和减少性能的分散性;采用合理的工艺条件,确保添加剂的均匀分散与减少玻纤的磨损,得到适于军工、航空和机电等领域需要的高性能的受力结构工程塑料。     

稳定锐态型钛白粉分散性能工业试验

试验分别用水性分散剂和油性分散剂对钛白粉半成品进行粉碎包膜，检测成品的应用性能，发现水性分散剂效果不明显，而油性分散剂对分散性和分散稳定化程度都有提高，同时分析了在锐态型钛白粉行业产品包膜效果的影响因素，以供参考。     

新型处理药剂（EP-110）处理各种重金属离子的实验研究

各行各业生产过程中会产生大量废水,重金属离子污染物是其中的重要控制指标,传统的处理方法不能完全解 决这类污染。本文通过大量的实验数据,对新型的处理药剂(EP-110)处理各种重金属离子的性能做了全面的测试、分析,并 提出了使用方法。     

移动IP的关键技术

本详细描述了移动IP的工作过程，并介绍了移动IP的隧道技术和IPSec，最后对移动IP技术中存在几个热点问题进行了讨论。     

Short fibre elastomer composites: effect of fibre length,orientation, loading and bonding agent

A series of short fibre reinforced styrene butadiene rubber (SBR) composites were prepared by incorporating sisal fibres of different lengths and different concentrations. The vulcanization behaviour and the properties of the vulcanizates were measured by the relevant ASTM procedures. The processing characteristics such as green strength and mill shrinkage were improved by the addition of fibres. The properties like tensile strength, tear strength, moduli at 10% and 20% elongations were found to be maximum for composites containing longitudinally oriented fibres of length 6 mm. Mixes containing 35 phr loading of fibres and bonding agent showed better mechanical performance than others. The failure behaviour of tensile and tear specimens have been analysed by scanning electron microscopy techniques. Paper presented at the poster session of MRSI AGM VI, Kharagpur, 1995