Calcium addition in straw gasification

The present work focuses on the influence of calcium addition in gasification. The inorganic-organic element interaction as well as the detailed inorganic-inorganic elements interaction has been studied. The effect of calcium addition as calcium sugar/molasses solutions to straw significantly affected the ash chemistry and the ash sintering tendency but much less the char reactivity. Thermo balance test are made and high-temperature X-ray diffraction measurements are performed, the experimental results indicate that with calcium addition major inorganic-inorganic reactions take place very late in the char conversion process. Comprehensive global equilibrium calculations predicted important characteristics of the inorganic ash residue. Equilibrium calculations predict the formation of liquid salt if sufficient amounts of Ca are added and according to experiments as well as calculations calcium binds silicon primarily as calcium silicates and less as potassium calcium silicates.     

Effect of carbide additions on grain growth in TiC−Ni cermets

The growth of carbide particles in TiC-XC-2 vol.% Ni and TiC-XC-30 vol.% Ni alloys, where X=Zr, Cr, W, Ta and Mo, was fitted to an equation of the form d³-d_o ³=Kt. The grain growth behavior during liquid phase sintering at 1673K decreased markedly with the addition of Mo₂C or WC, changed little for TaC, and increased with the addition of ZrC or Cr₃C₂. The grain contiguity decreased with increasing Ni content in the TiC−Mo₂C−Ni alloy and was greater in the alloys with smaller growth rate constant. Consequently, the effect of carbide addition on the grain growth of 2 vol.% Ni alloys was found to be similar to that of 30 vol.% Ni alloys. The grain growth mechanism could be explained by the effect of contiguous carbide grain boundaries in restricting the overall grain growth, as well as the area of the solid/liquid interfaces in the alloy by the usual solution/reprecipitation model.     

mc-Si:H/c-Si solar cell prepared by PECVD

Hetero-junction solar cells with an mc-Si:H window layer were achieved. The open voltage is increased while short current is decreased with increasing the mc-Si:H layer's thickness of emitter layer. The highest of V oc of 597 mV has obtained. When fixed the thickness of 30 nm, changing the N type from amorphous silicon layer to micro-crystalline layer, the efficiency of the hetero-junction solar cells is increased. Although the hydrogen etching before deposition enables the c-Si substrates to become rough by AFM images, it enhances the formation of epitaxial-like micro-crystalline silicon and better parameters of solar cell can be obtained by implying this process. The best result of efficiency is 13.86% with the V oc of 549.8 mV, J sc of 32.19 mA·cm-2 and the cell's area of 1cm2.     

发电机同轴励磁机电刷火花过大的原因及处理方法

本文对发电机同轴励磁机电刷火花过大的原因进行了分析．并针对这些原因提出了相应的处理办法。对规范励磁机的运行维护有很大的帮助。     

论直流电动机换向火花的检测与调整

本文着重探讨直流电动机换向火花的形成、征状以及使用的一些对其进行判别、调整的简单方法，并阐述其原理及效果。     

短纤维增强透气性莫来石/铁(A3S2/Fe)复合材料烧结特性的研究

本文研究了A₃S₂/Fe复合材料的烧结特性、透气性和纤维增强效果,分析了烧结过程中材料宏观结构和微观组织的形成机理.实验结果表明:纤维增强A₃S₂/Fe复合材料在900～1000℃具有良好的烧结性能,烧成后表层存在一定厚度的硬化层;纤维增强效果显着.材料抗压强度达17～23MPa,相对透气系数为4.30～9.69cm3/(cm2·s·atm).已能满足实际应用的需要.     

高频MnZn功率铁氧体烧结工艺研究

按照氧化物陶瓷工艺对高频MnZn功率铁氧体烧结工艺条件进行了研究。烧结温度越高，晶粒越大，晶界越薄，电阻率越低，磁芯损耗越大，起始磁导率和烧结密度分别在1240℃和1230℃达到最大值。延长保温时间，可以使晶粒充分生长，晶界变薄，电阻率减小，损耗增大。保温3h后，起始磁导率和烧结密度均可达到最大值。氧分压越低，材料起始磁导率越高，电阻率越小，损耗越大，但氧分压低于5％后烧结密度不再继续增加。     

纳米陶瓷的制备

纳米陶瓷材料可显著降低材料的烧结致密化程度,节约能源;并可改善陶瓷材料的性能,提高其使用可靠性。主要介绍了纳米陶瓷的制备方法,包括纳米陶瓷粉体的制备、成型和烧结。     

The Influence of Medium on Low-Voltage Circuit Breaker Arcs

This paper mainly focuses on the influence of three kinds of media： air, air-10%PA （Nylon） and air-10% POM （polyoxymethylene） on low-voltage circuit breaker arcs. A threedimensional （3-D） model of arc motioa under the effect of external magnetic field is built based on magnetohydrodynamics （MHD） equations. By adopting the commercial computational fluid dynamics （CFD） package based on the control-volume method, the above MHD equations are solved. For the media of air-10%PA and air-10%POM, the distributions of stationary temperature and electrical potential and the transient motion processes are compared with those of air arc. The research shows that both air-10%PA and air -10% POM can cool the arc plasma and the former is more effective. Both of them can increase the stationary voltage as well. Moreover, the presence of the two mixtures can accelerate the arc motion toward the quenching area and ensures the arc quenched in time.     

首钢烧结生产技术近年来的发展与进步

近几年来，炼铁厂烧结生产通过改进工艺技术和设备，使烧结产质量稳步提高，在满足高炉生产需要的同时，实现了低耗、清洁的目标。