DC-DC变换器突加负载时的动态性能研究

提出了一种能够有效改善DC-DC变换器动态性能的方案。该方案是在全桥电路基础上并联一单端正激变换电路，使变换器负载从10%轻载突加到100%满载时，其暂态过程小于1μs输出电压达到设计要求。文中对具体电路进行了详细分析，并通过仿真进行了验证。     

砖混结构现浇楼板的裂缝分析及预防措施

针对目前多层住宅采用砖混结构现浇钢筋混凝土产生裂缝的情况，分析了其产生原因，提出了预防措施。指出这些预防措施可使裂缝得到有效控制。     

基于PLC电液比例控制的液力测功装置开发及其应用

本文介绍一种齿轮动态加载试验规范及技术要求，论述了运用电液比例控制技术所设计的液压加载系统原理及其使用效果，并简述由此构造的液力测功装置的原理与应用前景。     

冬冷夏热地区户式空调设计与节能分析

以一单元式住宅的风道式户式空调系统为例，探讨了冬冷夏热地区户式空调的新风量确定方法，分析了户式空调的负荷特性，节能设计及户式空调系统的设计负荷与设计风量。     

大跨度钢桁架桥的施工与实践

介绍了天生桥一级水电站引水道进水塔大跨度钢桁架桥施工的全过程，包括制作，运输、安装、试验等几个部分，以供类似工程施工参考。     

Residue curve maps for reactive distillation systems with liquid-phase splitting

A model has been developed to study the effects of chemical kinetics on the residue curve maps (RCM) for reactive distillation systems with liquid phase splitting. In the model, chemical reaction can occur in both or only one of the two liquid phases. The heating policy V/V₀=H/H₀ is applied so that the kinetic effect can be described by a single parameter, the Damköhler number Da. The effects of reaction kinetics on pseudohomogeneous and heterogeneous mixtures have been compared. The properties of their RCMs are the same outside, but are fully different inside the liquid-liquid (L-L) region if they have different chemical equilibrium curves. Inside the L-L region, the chemical equilibrium curve coincides to a unique reactive liquid-liquid tie line in case that the pseudohomogeneous chemical equilibrium curve intersects with the L-L envelope. When the reaction occurs in only one of the two liquid phases, the residue curves inside the L-L region are strongly affected by the L-L envelope, especially at high Da. In the present paper, first an illustrative arbitrary reaction system, and then the reaction of cyclohexene with water to cyclohexanol are analysed with respect to their RCMs.     

加载单极子天线的时域辐射特性

基本的单极子天线由于其本身的特社会在天线内部对馈入的信号进行多次反射，严重,制约着它的辐射性能。采用时域有限差分法对比计算了加载与非加载单极子天线的时域辐射特性。计算结果表明，加载是改善单极子天线时域辐射性能的最佳选择，但需要以牺牲辐射效率为代价。     

船艇电站仿真与综合管理系统

论文介绍了船艇电站模拟器的组成和实时仿真功能,着重描述了多层次的图形管理系统及其仿真界面。课题将多媒体课件制作与模拟器有机地结合,涵盖了船舶主要电气设备的控制电路,既利于实践训练又便于原理的讲解,并在实践中取得了良好的效果。     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.