包钢CSP生产线HP295焊接气瓶用热轧钢带研制和开发

通过合理的化学成分设计和控制轧制、控制冷却技术的应用,包钢钢联公司薄板坯连铸连轧厂成功地开发和研制出了HP295焊接气瓶用热轧钢带,并对批量试生产产品的性能和金相组织进行了分析。     

钢筋混凝土用钢筋SD390产品开发

介绍了日标对SD390的要求及其开发过程。     

国内管线钢标准应用现状分析

简要介绍了国内管线钢的组织分类及其特性要求,并对国内管线钢目前应用标准情况进行了分析研究。     

安钢高线品种开发的优势与实践

介绍了安钢高线的技术装备、工艺转化及创新，以及自投产以来的产品结构调整和重点产品的开发情况。     

热轧板带板形检测发展分析

分析了国内外热轧板带的板形检测技术及几种板形检测方法的发展应用状况,并就热轧板带产 品的发展及要求展望了未来板形检测的发展方向。     

无取向硅钢热轧板形控制与轧制特性的关系

无取向硅钢板形质量要求日趋严苛。热轧是控制无取向硅钢成品横截面厚差偏大、尤其是边部减薄显著的关键工序。通过测试并分析无取向硅钢板形控制与专有轧制特性的关系,提出可通过采用合理的ASR非对称自补偿工作辊和常规工作辊的辊形配置及相应的窜辊策略可有效控制带钢边部减薄和凸度,使板形质量达到用户要求。     

AOD冶炼脱碳反应模型与计算机模拟

AOD冶炼中,终点碳和终点温度的命中率是提高生产率和产品质量的关键。由初始温度,初始成分及补加合金量等原始数据,通过本模型可预报要达到目标终点碳所需要的脱碳时间以及相应的终点温度。本模型计算得到的终点碳与实际终点碳,在同等条件下,两者极为接近,可作为一般AOD冶炼中预报终点碳与脱碳时间关系之用。通过分级调整O2、Ar、N2气比例得到最佳脱碳效果,终点碳命中率可提高到98％以上,最高温度可以控制不超过1750℃,延长炉衬寿命。     

浅析影响SCR法铸坯质量的因素

分析了SCR连铸连轧工艺生产铜银合金导线时,铸坯凝固的热阻界、铸模的传热条件、铸坯组织的控制对产品质量的影响。     

Tests During Three Stages of Construction of a Road Bridge with a Flexible Load-Carrying Structure Made of Super Cor Type Steel Corrugated Plates Interacting with Soil

The way in which a new road bridge made of steel corrugated plates Super Cor type was tested during the three stages of its construction is described and the test results are presented. Backfill in construction Stage I and two ballasting vehicles in Stages II and III constituted the loads. The box bridge spans the Bystrzyca Dusznicka River in Polanica Zdroj, Poland. The span’s effective length is 12.27?m and its vertical inside diameter is 3.85?m. The steel span is founded on two reinforced concrete strip foundations. The average values of the displacements and strains (normal stresses) measured in selected points and on selected elements of the steel shell structure were much smaller than the ones computed for the same load. The conclusions drawn from this research can be helpful in determining the interaction between the steel shell and the backfill. Since this type of steel–soil structure is increasingly used in Poland and in the world, the conclusions can be generalized to a whole class of similar bridge designs.     

Recent Progress on Non‐oriented Silicon Steel

Control of crystalline orientation and consequent enhancement of magnetic properties are important for decreasing core loss of non‐oriented silicon steel as well as grain‐oriented silicon steel. Through the development of special process techniques to produce clean refined steel, it is now possible to use any element to improve the crystalline texture control of steel without producing harmful effects. Utilization of these effects have actually lowered the core loss and raised the magnetic flux density of the products, and a product series of high‐efficiency non‐oriented silicon steel has been developed. Recently, demand has grown for non‐oriented silicon steel with particular properties, such as lower core loss at high frequencies or high strength, as high‐speed motors have progressed in regard to high efficiency and miniaturization. In response to this trend, non‐oriented thin gauge silicon steel with a thickness of 0.20 and 0.15mm and high strength non‐oriented thin gauge silicon steel with the same thickness but a yield strength of more than 570MPa and 780MPa have been developed.