A low wall-loading DEMO reactor design with high priority for early and reliable realization of a tokamak fusion reactor over the cost performance

Based on scientific databases adopted for designing ITER plasmas and on the advancement of fusion nuclear technology from the recent R&D program, a low wall-loading DEMO fusion reactor has been designed, where high priority has been given to the early and reliable realization of a tokamak fusion plasma over the cost performance. Since the major radius of this DEMO reactor is chosen to be 10 m, plasma ignition is achievable with a low fusion power of 0.8 GW and an operation period of 4–5 hours is available only with inductive current drive. The low ignition power makes it possible to adopt a first wall with an austenitic stainless steel, for which significant databases and operating experience exists, due to its use in the presence of neutron irradiation in fission reactors. In step with development of advanced materials, a step-wise increase of the fusion power seems to be feasible and realistic, because this DEMO reactor has the potential to produce a fusion power of 5 GW.     

强磁场对硅锰铸钢于A_1点附近等温珠光体相变的影响

通过开展12 T强磁下硅锰铸钢(50Si_2Mn_3)于A_1点温度附近不同等温时间的热处理试验,并对比强磁场与无磁场条件下等温珠光体相变试验结果,研究了磁场对珠光体转变量及组织形貌的影响。研究表明,对于50Si_2Mn_3在A1点以下较高温度范围内,强磁场可缩短珠光体相变的孕育期,促进硅锰铸钢珠光体转变,使其转变量明显增加;强磁场能够提高珠光体转变临界点,使50Si_2Mn_3在A1点以上等温过程中能够发生珠光体相变。     

二溴对甲基偶氮甲磺光度法测定钢中微量锶

研究了二溴对甲基偶氮甲磺与锶生成2:1兰色络合物进行钢中微量锶的测定.该法λ_(max)=638nm,摩尔吸光系数E_(638)=5.01×10~4,锶量在0.02～0.34μg/L范围内服从比尔定律.方法已用于钢中微量锶的测定,结果满意.     

基于多目视觉的变形钢板三维测量方法

提出了一种使用4个相机测量变形钢板三维形状的方法;在没有纹理的钢板上画一些点,使用4个相机同时拍摄钢板;利用边缘检测算法找出钢板的边缘,利用特征点提取算法提取出4个图像中钢板上的特征点,并找到4个图像上精确的特征点匹配关系,然后测量出这些特征点的三维点;最后,以这些三维点为种子点向外区域增长,从而得到钢板的三维形状;实验对变形钢板进行三维测量,得到了钢板的精确的三维形状,结果验证了该方法的有效性和可行性。     

不锈钢活性炭滤器的氯腐蚀与防腐

本文就活性炭在预处理中脱氯的不锈钢滤器的氯腐蚀机理进行了探讨，并提出了不锈钢活性炭脱氯滤器的防腐方法和措施。     

A method for observing the three-dimensional morphologies of inclusions in steel

A method for observing the three-dimensional morphologies of inclusions by deeply eroding a steel sample with a kind of organic solution composed of bromine water,acetone,and HC1 (volume ratio,45∶45∶10...     

Corrosion-resistant analogue of Hadfield steel

The concept of alloying austenitic steels with carbon + nitrogen is used for the development of a corrosion-resistant austenitic CrMn steel having an impact wear resistance close to that of the Hadfield steel. A higher stabilization of the austenitic phase by C + N, as compared to carbon or nitrogen alone, is substantiated by ab initio calculation of the electron structure, measurements of the concentration of free electrons and calculations of the phase equilibrium. Based on these results, the compositions (mass%) Cr18Mn18C0.34N0.61 and Cr18Mn18C0.49N0.58 were melted and tested along with Hadfield steel Mn12C1.2. Mechanical tests have shown that, as compared to the Hadfield steel, the experimental steels possess a higher strength, plasticity, hardness and the same resistance to impact wear. TEM studies of the surface layer after impact treatment revealed a mixture of the amorphous phase, nanocrystals and fine-twinned austenite. At the same time, using Mössbauer spectroscopy of conversion electrons, the ferromagnetic ordering was found in the surface layer of up to 10 μm in depth, which is the sign of the strain-induced martensitic phase. The hypothesis of a transition from the low-spin to the high-spin state of the iron atoms within the thin twins in austenite was proposed in order to interpret the discrepancy between TEM and Mössbauer studies. Potentiodynamic measurements and immersion tests show that the CrMnCN steels possess a significantly higher pitting potential and resistance to general corrosion in comparison with Hadfield steel.