一种新的修正恒模算法

阐述了恒模算法(CMA)、修正恒模算法(MCMA)和判决引导(DD)算法的基本原理。针对CMA和MCMA收敛速度慢,固定步长条件下收敛速度和剩余误差之间存在矛盾的缺陷,在分析CMA误差特性的基础上,利用DD算法误差函数的模值和判决器输出构造新的误差函数,提出了一种新的变步长MCMA。新算法在加快收敛速度的同时保持小的剩余误差。仿真结果表明,新算法比CMA和MCMA收敛速度快,均衡输出剩余码间干扰(ISI)小而且能克服相位偏移,具有很好的实用性。     

冲压-刚度的耦合仿真分析技术

提出冲压——刚度的耦合仿真方法，即用动力显式算法计算冲压，静力隐式算法计算回弹，用动力显式算法计算最终的刚度，给出耦合仿真过程中3个环节的实施过程及其关键技术点。应用本方法对双曲率的盒形件进行了刚度仿真分析，并和试验结果进行了比较，取得了令人满意的计算精度。     

地聚合物混凝土配比及力学性能研究

混凝土是巷道支护过程中的重要建筑材料,然而混凝土在巷道施工中常常出现质量问题,为了不影响正常生产,需要对其进行修补。地聚合物混凝土凝结时间快,早期强度高,界面结合能力强,耐高温性和抗冻性强,耐腐蚀性良好,具有用作修补材料的潜力。以粉煤灰和矿粉为原料,Na₂SiO₃溶液和NaOH为碱激发剂制备地聚合物胶砂,研究不同的碱激发剂模数（1.0、1.2、1.4）和掺量（10%、15%、20%）对不同龄期胶砂力学性能的影响。结果表明：当碱激发剂模数为1.2,碱掺量为15%时,胶砂强度达到最大值。设计正交试验,研究了不同水胶比（0.45、0.50、0.55）、粉煤灰掺量（30%、50%、70%）和砂率（30%、35%、40%）对不同龄期地聚合物混凝土的工作性能和力学性能的影响。结果表明：粉煤灰掺量对抗压强度影响最为显著,水胶比次之,而砂率对强度发展几乎没有影响。最优的配合比为水胶比为0.50,粉煤灰掺量为50%,砂率为35%。     

Aging and mechanical properties of NR/BR blends

The mechanical properties and post-thermal aging properties of natural rubber (NR) and polybutadiene rubber (BR) blends at different blending ratios are investigated herein. The experimental results show that both tensile and tear strengths of NR/BR blends increase with increasing NR content. BR has a higher compression stiffness than NR. The deformation of BR is less than that of NR under the same load conditions. With regard to aging properties, both tensile stress and strain of NR/BR blends decrease after prolonged aging. In addition, the stress loss of BR is lower than that of NR, meaning that the aging resistance property of BR is superior to that of NR. Furthermore, accumulated thermal history has shifted the glass transition temperature (T _g) of NR/BR blends toward lower temperatures while the loss tangent (tan δ) value increases with prolonged thermal aging.     

压入深度与膜厚对薄膜与基体复合硬度及弹性模量的影响

根据高华建的复合弹性模量模型，提出了用一个测点的载荷-位移曲线计算整个压入深度内薄膜和基体复合硬度分布的方法，探讨了压入深度与膜厚对硬度与弹性模量测量值的影响，指出可由膜-基复合性能反推膜本身的性能。     

熔模铸造型壳抗弯弹性模量的研究

依据材料力学、陶瓷材料的有关理论和方法,分别对水玻璃型壳、硅溶胶型壳及其复合型壳在不同温度时的抗弯弹性模量进行了测试研究.结果表明,耐火材料、温度对型壳的弹性模量有较大的影响,硅溶胶型壳和复合型壳的弹性模量值比水玻璃型壳的大.     

Effect of cold spray deposition of a titanium coating on fatigue behavior of a titanium alloy

The deposition of titanium on a titanium alloy substrate is being examined for potential use as a surface treatment for medical prostheses. A Ti6Al4V alloy was coated with pure titanium by cold gas dynamic spraying. Coatings were deposited onto samples with two different surface preparation methods (as-received and grit-blasted). The fatigue life of the as-received and grit-blasted materials, both before and after coating, was measured with a rotating-bend fatigue rig. A 15% reduction in fatigue endurance limit was observed after application of the coating to the as-received substrate, but no significant reduction was observed on its application to the grit-blasted substrate. The reduction in fatigue endurance limit has been related to the substrate-coating interface properties, the elastic modulus, and the residual stress states. This article was originally published inBuilding on 100 Years of Success, Proceedings of the 2006 International Thermal Spray Conference, (Seattle, WA), May 15–18, 2006, B.R. Marple, M.M. Hyland, Y.-Ch. Lau, R.S. Lima, and J. Voyer, Ed., ASM International, Materials Park, 2006.     

在纳米压入仪上进行悬臂梁法测量弹性模量的影响因素分析

对在纳米压入仪上进行悬臂梁法测量弹性模量的主要影响因素进行了综合分析,主要包括加载系统悬置弹簧刚度、压头压入、梁沿截面宽度方向挠曲、梁支座附加挠曲等影响。在考虑这些因素的基础上,得到了悬臂梁的有效挠度,利用有效挠度与载荷之间的关系,评价悬臂梁材料的弹性模量。对单晶硅(100)悬臂梁试样进行了实验,得到其弹性模量为155GPa±9.5%GPa,与参考文献值符合较好。表明在纳米压入仪上进行悬臂梁法测量,只有综合这些影响因素后,才能获得有效、准确的弹性模量测量结果。     

Some new operational modes and parameters of stress relaxation for the viscoelastic characterization of solid polymers. III. The area ratio mode and the intrinsic “strain–clock” function

The introduced area ratio mode of operation with its corresponding parameters seems to have a fairly high sensitivity to the viscoelastic response of the solid polymer. This appeared from the fact that a good distinction among the linear viscoelastic, the nonlinear viscoelastic, and the viscoplastic ranges of behavior can be made. By using a relevant rheological modeling and its corresponding algorithmical approach, in the case of isotactic polypropylene, this material can be characterized as a morphological three‐phase material consisting of an intraspherulitic crystalline, an amorphous phase, and a interspherulitic para‐crystalline phase. In this sense, the material was simulated using two models: the Poynting–Thomson and the Maxwell–Wierchert, from where a good response of the material to the first model appeared. The so‐called intrinsic “strain–clock” function and its corresponding coefficient of strength of nonlinear viscoelastic behavior, which were relieved by the experimental data, seem to be some powerful and very practical “tools” that can give a proven suplementary characterization of the material. Finally, by this intrinsic function, the existence of permanent internal stresses, was confirmed, in an indirect way, which was mentioned in part II of this study. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 149–158, 2003     

Adhesion Mechanisms of Polyurethanes to Glass Surfaces I. Structure-Property Relationships in Polyurethanes and Their Effects on Adhesion to Glass

Polyurethanes were prepared from toluene diisocyanate (TDI), 1-4-butane diol (BDO) and polycaprolactone-based triols with varying molecular weights. Among each molecular weight triol-based urethane, hard segment content was varied from 20% to 70%. Differential scanning calorimetry, tensile testing, and Iosipescu shear testing were done on all the various urethanes prepared. Thermal characterization data revealed the dependence of phase separation on hard segment content as well as on the triol molecular weight. Tensile data and Iosipescu shear data further confirmed the observations made from the DSC data. The data further indicated that phase separation can greatly improve the modulus of cross-linked segmented urethanes. Adhesion of these urethanes to glass surface was evaluated using soda-lime float glass plate. Urethane samples were cast on the air side of the glass plates and adhesion was measured in shear mode. Adhesion data indicated that in addition to hard segment content, modulus, cross-link density, and molecular weight of the triols, phase separation seems to be a major factor in controlling adhesion. Surfaces of the failed adhesion samples were also analyzed and the failure mode was found to be cohesive, in varying degree, with the different urethane systems.