混凝土大坝导温系数反演及其随时间变化的规律

随着时间的推移,混凝土的导温系数将发生变化,为了了解参数随时间的变化规律,利用原型观测资料对导温系数进行分段反演,从而拟合出大坝混凝土导温系数随时间的变化规律.     

Swelling behavior induced by alteration in granite and its implications on underground excavation

Granite is commonly recognized as an ideal medium for underground construction. However, in the site investigation for Heimifeng Pumped Storage Power Station project, it was found that there are swelling behaviors induced by alteration in granite and eventually causing slaking and disintegration of rock blocks. The study shows that hydrothermal alteration in granite is primarily due to the intrusion of multi-phase igneous magma. The clay minerals, such as montmorillonite, chlorite, kaolinite, are the main causes for the swelling behavior of granite. In the exploratory adits, alteration was observed to occur mainly along faults or fractures in the rock masses and resulted in roof caving if water is present. Some of the highly altered borehole cores swell and crack within 24 h in water and eventually disintegrate completely. From the testing results on the samples, the maximum axial free swelling strain is about 1.2%, while the maximum axial confined swelling strain is around 0.1% with swelling stress less than 25 kPa. Under free swelling tests, 80% of swelling is completed within 24 hours. Under confined swelling condition, swelling process is completed within 1 h for some samples, with 80% of maximum swelling strain finished within around 22 h for most of the samples. Contraction of samples occurs after swelling completed. The strength of granite, reflected by deformation and elastic moduli, shear strength, decreases due to alteration. The deformation and elastic moduli are even lower compared to highly weathered rock. The shear strength is between that for highly weathered and slightly weathered rocks. The swelling characteristics of the altered rock present great challenges for support or lining during construction and operation stages. Support or lining shall be in place immediately after excavation. Since the rock may swell when encountering water, the shotcrete shall be designed accordingly. During the construction of access tunnel and caverns, water shall be drained in time. Drainage directly from surface shall be avoided so as to prevent floor heave.     

Influence of polymer modulus on the percolation threshold of latex-based composites

Monodispersed copolymer emulsions with different glass transition temperatures were synthesized to investigate the effect of room temperature polymer matrix modulus on the electrical properties of carbon black (CB) filled segregated network composites. The emulsion with the highest modulus at room temperature produced composites with the lowest percolation threshold. The threshold for a composite made from a copolymer latex containing an equal ratio of butyl acrylate and methyl methacrylate (BA5) is 1.5 vol%, while the percolation threshold for the much lower modulus BA7 (7:3 BA/MMA ratio) is 4.93 vol%. The microstructure of each composite shows significant differences in the level of CB dispersion within the polymer matrix. Higher modulus polymer particles push the CB more efficiently into the interstitial space between them, resulting in a lower percolation threshold. This modulus effect was confirmed by increasing the drying temperature, where the moduli of latexes (BA5, BA5.5, and BA6) were more similar and the percolation thresholds for three composites also become closer to one another.     

橡胶Mooney—Rivlin模型材料系数对轴向刚度影响分析

在橡胶小变形范围内，采用理论推断的方法，得到在相同硬度下橡胶Mooney—Rivlin模型材料系数由C2／C1决定的关系式。并采用ABAQUS有限元软件分析的方法，结合橡胶轴向刚度常规解，分析了C2／C1不同值对橡胶轴向刚度的影响进行，结果显示其影响呈现一定规律性。     

Analytical prediction of composite beams response in fire situations

In this paper an extension of the method of the Fourier series expansion to the fire analysis of composite beams is presented. In particular the extension concerns the introduction of the temperature dependent interaction of all the components: steel beams, concrete slab and steel connectors. These last are considered of finite stiffness, and a proper account is given to the combined effect of thermal degradation of the properties, and stress amplification caused by the differential thermal expansion across the interface.The proposed method compares very well with some experimental fire tests of simply supported and framed composite beams. Due to its relative simplicity and speed, it can be used for design purposes in evaluating the critical temperature in terms of critical deflection. Finally we recall that the method is capable of dealing with every type of fastening distribution, such as discontinuous or variable length.     

静载荷和疲劳载荷作用下 C/Al 正交层压板的力学响应

本文讨论静载荷及疲劳载荷作用下 C/Al 正交层压板的力学响应,并考虑损伤过程中的临界现象,以此作为结构设计准则的基础。对静载荷作用的情况:(1)90°铺层的门槛应变ε_(FPF)随着约束程度增加而增加,而且开裂后的行为也受约束程度的影响。(2)经历加载-卸载再重新加载至断裂的过程后,初始试样存在一个剩余永久变形,其损伤状态可以用刚度的变化来表征;而疲劳试样在加载-卸载过程中刚度变化很小,反映其损伤达到一个稳定的状态。对疲劳载荷作用的情况:(1)对于给定的应力比 R,试样会趋于与它所承受的 S_(max)最大值相应的 SDS 状态。循环应力范围的不断增大,会引起基体损伤的增加,从而重新建立新的饱和损伤状态。(2)对于每一损伤状态均有一对应的循环应变范围 Δε。在 SDS 状态下,Δε保持不变。(3)以刚度下降为损伤参数对 C/Al 层压板进行了降级应力分析,并由此来预计在ΔS_(sh)以下,层压板不会发生疲劳损伤累积。     

空间柔性机械臂三维动力学数值仿真

本文应用ｄ＇Ａｌｅｍｂｅｒｔ－Ｌａｇｒａｎｇｅ原理，对由基座、（ｎ－１）个柔性连杆及端部负载组成，相互用柱铰连接的柔性链式多体系统进行建模；对在空间技术中，具有一刚杆，两柔杆加上刚性负载所组成的三维机械臂系统，采用Ｇｅａｒ算法进行数值仿真。仿真结果比较符合实际，从而在柔性多体系统的数学模型为刚性常微分方程的情况下，为解决其数值仿真问题，特别是三维问题的数值仿真取得了进展。     

Frequency response function of magnetic bearings using high-temperature superconductor

A high-temperature superconductor YBa₂Cu₃O_7-x with strong pinning force has allowed stable magnetic suspension with no control to be developed. Two types of superconducting magnetic bearings (SMB) using YBCO and permanent magnet were assembled. The two types are radial and axial. The dynamic stiffness of each SMB as it was cooled down under a magnetic field by liquid nitrogen was measured both radially and axially. As a result, it was found that the spring constants of these SMBs were almost as large as a practically desirable value; however, their damping coefficients were lower than the practical level. These findings are useful as one of the data bases for development of an optimum SMB design to support the weight of rotors in an axial direction.     

Charge density dependence of elastic modulus of strong polyelectrolyte hydrogels

The mechanical behavior of a series of strong polyelectrolyte hydrogels based on acrylamide and 2-acrylamido-2-methylpropane sulfonic acid sodium salt (AMPS) was investigated. The hydrogels were prepared at a fixed crosslinker ratio and monomer concentration, but at various charge densities, i.e. AMPS contents between 0 and 100 mol%. The elastic modulus of the hydrogels after their preparation first increases with increasing charge density but then decreases continuously. Investigation of the swollen state properties of the hydrogels shows existence of a large number of ionic groups inside the gel that are ineffective in gel swelling. The results indicate two opposite effects of charged groups on the elastic modulus of the hydrogels: formation of multiplets acting as additional crosslinks in the gel increases the elastic modulus of ionic hydrogels, whereas the effect of the electrostatic interaction of charged groups on elastic free energy decreases the modulus.