降温速率对Ba0.92Ca0.08TiO3 PTCR陶瓷室温电阻率"反常"现象的影响

通过系统研究烧结工艺对BaO92Ca0.08TiO3电阻正温度系数(possitive temperature coefficient resistance，PTCR)陶瓷的影响，在晶粒生长过程中分析液相在晶界中的分布。着重研究降温速率对PTCR室温电阻率的影响。发现在1300～1150℃温区内，当降温速率大于15℃／min时，出现随降温速率增加，室温电阻率增大的“反常”现象。根据液相在晶界区分布随降温速率的变化规律，对这种“反常”进行解释。     

表面处理对氮化硅陶瓷力学性能的影响

采用X射线衍射应力分析的sin2ψ法计算了Si3N4陶瓷试样的残余应力，并分别测量了表面处理前后Si3N4试样的力学性能。结果表明，经平面磨削后的Si3N4试样表面残余应力为拉应力，而抛光处理可适当降低残余应力。两种方法都使试样抗弯强度降低。     

丙烯抗冲共聚产品EPF30R的开发

介绍了聚丙烯抗冲共聚产品EPF30R的工艺生产特点,并详细阐述了EPF30R重要物理性能与相关工艺控制参数的关系。通过调整TEAL/DONOR比、液相和气相聚合中的氢气浓度、气相组份和乙烯含量,使多相共聚物EPF30R具有良好的高刚性、流动性和冲击性能。     

偶联剂处理对碱式硫酸镁晶须填充UP树脂浇铸体力学性能的影响

利用钛酸酯类偶联剂NDZ101、NDZ401和硅烷类偶联剂KH550、KH570对碱式硫酸镁晶须进行处理,研究了几种偶联剂及其加入比例对晶须填充不饱和聚酯树脂(UP)浇铸体力学性能的影响,并结合应力-应变曲线和SEM的图片,对试验结果进行了讨论。实验结果表明,采用偶联剂处理晶须可改善其填充UP树脂浇注体的拉伸强度、拉伸模量、弯曲模量和冲击强度。其中,采用2%KH570进行处理,拉伸强度改善幅度最高,可提高47.54%;采用3%NDZ101进行处理,拉伸模量和弯曲模量均获得最大幅度的提高,分别为65.99%和69.33%;而采用4%KH550进行处理,却可最大幅度地提高冲击强度,为29.21%。对弯曲强度而言,偶联剂处理总体上对其影响效果不如其它的力学性能那样明显。相对而言,硅烷类偶联剂的效果优于钛酸酯类的偶联剂。加入4%KH570和5%KH550时获得的弯曲强度最大,分别为54.43MPa和53.19MPa,较未处理的浇铸体弯曲强度分别提高了25.10%和22.25%,而采用NDZ101或NDZ401,弯曲强度值却基本上都下降。碱式硫酸镁晶须填充UP树脂浇铸体的断裂属于脆性断裂。     

高温变换催化剂制备条件的神经网络优化

将影响低汽气比条件下LB型节能高温变换催化剂活性的主要因素作为人工神经网络的特征输入向量,将全部实验数据分为训练集和预测集,运用Matlab神经网络工具箱,按改进的Bayes自动归一化算法建立反向传播神经网络模型,不仅可防止网络陷入局部最小,而且提高了网络训练精度和泛化能力。适当拓宽正交实验各因素的水平范围,经过不同因素、不同水平间的组合模拟,预测出LB型节能高温变换催化剂的最佳制备条件为氧化铈质量分数0.76%、氧化铜质量分数5.8%、氧化铬质量分数8.6%、氧化镧质量分数1.0%、铁液浓度92 g/L、中和过程最终pH值9.5。在最佳条件下试制催化剂在低汽气比下的平均活性达77.6%。     

Restricted chain segment mobility in poly(amide) 6/clay nanocomposites evidenced by quasi-isothermal crystallization

Modulated temperature differential scanning calorimetry is used to explore the interactions between a poly(amide) 6 matrix and various types of clay reinforcement. During quasi-isothermal crystallization of the polymer/clay nanocomposites, an excess contribution is observed in the recorded heat capacity signal, due to reversible melting and crystallization. It is proposed that the magnitude of this excess contribution can be used to qualify the polymer/clay interfacial interaction, as it is directly linked to the segmental mobility of the polymer chains in the interphase region, where both the crystalline and amorphous polymer fractions are affected. It is shown that the interfacial interaction strongly depends on the type of clay filler used. These interactions play a key role in the development of specific material properties for the different types of nanocomposites. A simple interphase model for the poly(amide) 6/clay nanocomposites is proposed.     

稀土丁异戊橡胶改性天然橡胶的应用研究

采用稀土丁异戊橡胶代替顺丁橡胶，测试并分析了改性天然橡胶的低温性能及相关性能。结果表明，稀土丁异戊橡胶改性的天然橡胶室强力学性能和粘接性能与顺丁橡胶改性的天然橡胶相近，但低温性能有较大的改善。在-40℃下贮存2h后，顶丁橡胶改性天然橡胶硫化胶有明显的结晶现象，其剪切模量较室温下的相应值增加了6倍，而稀土丁异戊橡胶改性的天然橡胶硫化胶保持了良好的弹性，其剪切模量值与室温下的相当。     

受限节点的WSNs非均匀分簇算法应用研究

针对常规分簇路由算法不能有效解决节点位置、能量、频段受限的固态发酵温度检测无线传感器网络(WSNs)中节点过早死亡和能耗不均衡的问题,提出了一种基于粒子群优化(PSO)算法的非均匀分簇路由协议。首先,根据网络规模选择固定数目的簇首节点,然后,引入PSO算法和非均匀分簇机制,以簇首节点覆盖范围和簇内节点与簇首之间平均欧氏距离作为评价函数的影响因子,选取一组最优簇首。仿真实验结果表明:所提算法有效改善了受限节点无线测温网络"热区"效应,均衡了节点能耗,显著延长了网络生存周期。     

含温度补偿的便携式土壤水分测定仪研制

针对现有土壤水分测定仪的不足,研制了一种新型的便携式土壤水分测定仪。传感器快速测量出土壤温、湿度数据,GPS自动获取时间、经纬度信息,数据既可临时保存在仪器的存储芯片中,又可通过GPRS/GSM将数据及时发送到后台数据库和手机用户。通过温度补偿和野外验证实验得出,温度补偿项为Δy=0.0002 t3-0.011 t2+0.444 1 t-6.423 2,仪器所有功能运行正常,测量绝对误差为-3.64%~3.82%,平均绝对误差为2.24%,精度较高,适合在地方农技和水利部门推广应用,有助于农业水利信息化水平的提高。     

The effect of cooling rate on the impact performance and dynamic mechanical properties of rotationally molded metallocene catalyzed linear low density polyethylene

This article examines changes to the morphology of rotationally molded metallocene catalyzed linear low density polyethylene brought about by varying the cooling rate during processing. These changes in morphology lead to variations in the impact performance, which is reflected in the dynamic mechanical characteristics of the materials. Various analytical techniques are used in an attempt to explain the differences in impact behavior. Slow cooling is shown to result in high crystallinity, and in the formation of large spherulites, which in turn is detrimental to the impact performance of the material, particularly at low temperatures. The high crystallinity corresponds with a shift in the β transition of the material to a higher temperature, and is shown to result in a higher brittle–ductile transition. A case study was also carried out on samples from a finished part provided by an industrial molder, one section of which failed in a brittle manner when impact tested while the other failed in a ductile manner. Microscopy results showed that the brittle material had large spherulites at the inside surface, while the ductile material showed incipient degradation at this surface, which has previously been shown to be of benefit to impact strength in rotationally molded parts. Dynamic mechanical studies again showed a β transition at a higher temperature in the brittle samples. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1963–1971, 2006