大型矿车用减速机齿轮系统的疲劳分析

提出一种基于"放大因子"、采用二维平面单元模拟三维实体动态工况的计算疲劳的方法,对某矿车减速机齿轮系统进行疲劳分析,得到太阳轮、行星轮和扭力管在不同抗拉强度下的疲劳寿命.结果表明:太阳轮和扭力管最易发生疲劳破坏;齿轮寿命对抗拉强度的依赖性较敏感;得出的齿轮系统热处理后的抗拉强度建议值能为设计提供参考,且该方法能大大提高计算效率.     

校车车身结构的有限元分析

建立某型校车的有限元模型,计算在不同工况下其车身骨架的静态强度.计算结果表明:在弯曲和扭转工况下,该校车最大应力分别为154.8和171.4 MPa,均小于Q235屈服应力235 MPa;最大变形分别为4.925和12.92 mm,满足《客车定型试验规程(GB/T 13043—2006)》中所规定的弯曲和扭转工况下10及12 mm的限额;车身结构整体应力大多集中在30 MPa左右,有较大的安全裕度.分析结果可为该校车车身骨架结构优化提供参考.     

柴油发动机活塞静强度分析

针对铁路运输向高速重载方向发展对机车发动机性能要求不断提高的问题,为确保柴油发动机工作的可靠性,对其活塞进行静强度分析.用HyperMesh建立某柴油发动机活塞的三维有限元模型,利用ANSYS对其进行有限元分析.综合考虑热负荷与机械负荷的耦合作用,确定活塞最大应力和最大应变分布的危险部位.分析结果可以为铁路机车柴油发动机活塞设计提供参考.     

A型地铁空调系统及客室内流场数值分析

为给目前国内A型地铁车辆的舒适度设计提供理论参考,针对地铁车辆静压风道结构特点,基于k-ε两方程湍流模型和SIMPLE算法,建立包含空调送风风道和客室的三维计算模型.对计算模型的空气流动和传热状况进行CFD数值计算.计算过程综合考虑车体壁面传热和人体散热等多种传热.分析计算结果得到客室内温度场和速度场的分布规律,并对空调通风设计方案进行量化评估.计算结果表明:客室内人体头部区域温度场分布均匀,平均温度为26.6℃,最大温差为6℃;车厢内有较理想的气流组织形式,速度分布范围为0.50~0.79 m/s,而且客室端部和中部区域人体头部周围速度较大.将计算结果与欧洲EN 14750-1标准进行对比分析,认为乘客的舒适性较好.     

Effect of Cr3C2 on Valence-Electron Structure and Plasticity of Rim Phase in Ti(C,N)-Based Cermets

Based on the empirical electron theory of solids and molecules, the valence-electron structure (VES) of the rim phase in Ti(C,N)-based cermets was calculated, and the relationship between the VES and plasticity was determined. The results indicated that the plasticity of the rim phase in a Ti(C,N)-based cermet could be defined using the sum of the n _a values for the covalent bonds, and that chromium dissolution in the rim phase improved the plasticity of the rim phase. Moreover, a series of experiments showed that adding Cr₂C₃ to a typical Ti(C,N)-based cermet strengthened the interface. Based on those results, a Ti(C,N)-based cermet with added Cr₃C₂ was manufactured; the new cermet had more than twice the transverse rupture strength of a typical cermet.     

酯化反应偶联渗透汽化膜过程模型(Ⅰ)催化剂的影响

1 INTRODUCTION In former report, the kinetic model for anesterification process coupled by pervaporation wasestablished and the modeling result agreed well withthe experimental result[1].     

Brillouin-Scattering Study of the Elastic Constants of ErVO4

The room-temperature elastic constants of ErVO₄ were considerably smaller than those of isostructural silicate and phosphate analogs. The generally "less-rigid" crystalline lattice and weaker metal-oxygen bond-strength in the RVO₄ (R = rare earth elements) phases indicates that these materials are of interest for potential applications as an interphase component in toughened oxide ceramic composites.     

Experimental Evaluation of the Acceptor-States Compensation in Positive-Temperature-Coefficient-Type Barium Titanate

Experimental evidence shows that the acceptor-state levels in Sb-doped positive-temperature-coefficient-type BaTiO₃ are compensated up to a critical acceptor-state density. Using the slope of the natural logarithm of the resistivity with respect to 1/ T , instead of maximum resistivity as a measure for the acceptor-state density, it is possible to estimate this critical value. The value obtained (4.2 × 10¹⁷ m⁻²) is believed to be the first reported estimate based on experimental data. It is in good agreement with the estimate of 6 × 10¹⁷ m⁻² (first reported by Jonker) obtained from the spontaneous polarization of BaTiO₃. This shows that the ferroelectric behavior of BaTiO₃ is indeed a feasible explanation for the low resistivity below the Curie point, as proposed by Jonker.     

利用神木不粘性块煤炼制炭质还原剂

本文介绍利用神木不粘结性块煤炼制优质铁合金专用焦，通过对块焦的筛分组成分析、工业分析和灰分分析，焦炭的反应性能、比电阻、强度、石墨化程度研究，证明该煤炼制的块焦具有比电阻高，灰分、硫、磷、铝和高温下石墨化程度低的优点。该焦可代替冶金焦冶炼铁合金。     

在工程设计中采用循环流化床锅炉必须做好调查研究工作

本文概述了循环流化床锅的现状及发展,针对普遍存在的问题,指出在工程设计采用这类锅炉时,必须做好调查研究工作,向用户提供优质服务。