Determination of polymer–polymer interaction parameters using inverse gas chromatography

A modified method is discussed that is based on Farooque and Deshpande's method to obtain polymer–polymer interaction parameters using inverse gas chromatography (IGC) data. In the Farooque and Deshpande method, the ratio of the difference of probe–polymer interaction parameters between two polymers and the probe volume [(χ₁₂ ? χ₁₃)/V₁] is used as the abscissa. In the modified method, the ratio [(?₂χ₁₂ + ?₃χ₁₃)/V₁] is used as the abscissa. Experimental data previously reported for a poly(?‐caprolactone)‐polyepichlorohydrin (PCL/PECH) blend and a poly(ethyl acrylate)‐poly(vinyl propionate) (PEA/PVPr) blend are analyzed. It is found that the slopes obtained by the new method had smaller deviations from the theoretical values than the Farooque and Deshpande method. The standard deviations of both slopes and intercepts obtained from the new method are also smaller. Using the new method, the polymer–polymer interaction parameters obtained from the intercept are negative numbers for the PCL/PECH system and very small positive numbers for PEA/PVPr. Explanations are given for the probe and concentration dependency of the polymer–polymer interaction parameters that are generally observed in IGC studies. A new method for selecting the best probe for calculating the interaction parameter is discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 671–680, 2003     

Thermoreversible hydrogels. XIX. Synthesis and swelling behavior and drug release behavior for the N‐isopropylacrylamide/poly(ethylene glycol) methylether acrylate copolymeric hydrogels

A series of thermosensitive copolymeric hydrogels were prepared from various molar ratios of N‐isopropylacrylamide (NIPAAm) and poly(ethylene glycol) methylether acrylate (PEGMEA_n), which was synthesized from acryloyl chloride and poly(ethylene glycol) mono methylether with three oxyethylene chain lengths. Investigation of the effect of the chain length of oxyethylene in PEGMEA_n, and the amount of the PEGMEA_n in the NIPAAm/PEGMEA_n copolymeric gels, on swelling behavior in deionized water was the main purpose of this study. Results showed that the swelling ratio for the present copolymeric gels increased with increasing chain length of oxyethylene in PEGMEA_n and also increased with increase in the amount of PEGMEA_n in the copolymeric gels. However, the gel strength and effective crosslinking density of these gels decreased with increase in swelling ratio. Some kinetic parameters were also evaluated in this study. Finally, the drug release and drug delivery behavior for these gels were also assessed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1683–1691, 2003     

Preparation and characterization of a polyaniline/poly(butyl acrylate–vinyl acetate) composite as a novel conducting polymer composite

This is the first report on the preparation and characterization of a polyaniline/poly(butyl acrylate–vinyl acetate) composite. The composite was prepared by the emulsion polymerization of aniline in a medium containing poly(butyl acrylate–vinyl acetate). Films prepared from the composite (cast from an aqueous medium) had excellent mechanical properties and could be stretched up to 900%. The resultant composite was soluble in common organic solvents, and a stable water‐based dispersion could also be prepared. An electrical conductivity of 2.2 S cm^?1 was obtained. Cyclic voltammograms revealed that the composite was electroactive. It had excellent adhesion to either glass or steel plate. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2525–2531, 2003     

Molecular weight development in emulsion copolymerization of n‐butyl acrylate and styrene

The seeded emulsion copolymerization of n‐butyl acrylate and styrene in a weight ratio of 50/50 was investigated. The effect of the type of process (batch vs. semicontinuous) and the amounts of initiator and emulsifier charged into the reactor on the time evolution of the fractional conversion, number of polymer particles, and weight‐average molecular weight (M_w) was analyzed. It was found that the M_w depends to a slight extent on the type of process and the emulsifier concentration and to a larger extent on the initiator concentration. The molecular weight distributions (MWDs) and the gel content of the final latexes were also analyzed. In the absence of chain transfer agents (CTAs), the fraction of gel was higher in the semicontinuous processes. It was also found that the gel content increased with increasing initiator concentration in the recipe. The addition of 1 wt % CTA avoided gel formation and led to an important reduction of the M_w. Nevertheless, the MWDs presented a shoulder or even a second peak at high molecular weights that was due to reactions of chain transfer to the polymer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1918–1926, 2003     

Synthesis and rapid expansion in supercritical carbon dioxide through porous sintered metal plate of poly(1,1,2,2‐tetrahydroperfluorodecyl acrylate)

Poly(1,1,2,2‐tetrahydroperfluorodecyl acrylate) [poly(TA‐N)] was synthesized in dry benzene using AIBN as an initiator at 60°C. The effects of the monomer concentration (C_m), initiator concentration (C_i), and reaction time on the polymerization were investigated. The results of DSC and TGA showed that when the C_i remains constant, the higher the C_m value is, the better the thermal character for the product in the range of experiments. When the reaction was conducted for 30 h, polymerization is almost completed. The C_i should remain lower than 0.25 g/100 g monomer when the C_m is lower than 15 g/L. When the C_m is higher than 15 g/L, the C_i should be increased slightly. When the C_m remains constant, it was observed that an increase in the C_i increases the yield (mass of polymer after reaction/mass of monomer before reaction). On the other hand, the melting (T_m) and decomposition (T_d) temperatures of the reaction product decrease, except when the C_m reaches 20 g/L and the reaction time is 30 h. High purity CO₂ was continuously pumped using a high pressure syringe pump. Rapid expansion of poly(TA‐N) in supercritical CO₂ happened under control through a porous sintered metal plate. The poly(TA‐N) morphology was analyzed with a scanning electron microscope. An amorphous polymer was formed at a preexpansion temperature of 45°C. Fibers were formed at temperatures of around 60–80°C. An increase of the temperature slightly increases the particle size. At 105°C, most of the particles are spheres and dendrites. The corresponding CO₂ flow rate upon expansion was 2.5–5.0 ± 0.3 L/min (STP) and the pressure drop was 2 MPa. At the higher CO₂ flow rate, the spheres and dendrites became smaller. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2763–2768, 2003     

电子束固化聚氨酯丙烯酸酯的研究

电子束固化（EB）作为一种新型的固化技术,与传统固化方法相比较,具有高效,低成本,环保等优点,有着独特的优势,已经应用于印刷业、EB油墨和胶粘剂行业中.目前已经通过电子束固化成功的涂料主要是环氧树脂体系.文章对电子束固化的另一很有前景的体系水性聚氨酯丙烯酸酯固化的机理及发展进行综述.     

Semicontinuous heterophase copolymerization of vinyl acetate and butyl acrylate

Vinyl acetate (VAc) and butyl acrylate (BuA) were copolymerized in heterophase by a semicontinuous process (unseeded) and compared with the seeded semicontinuous microemulsion polymerization of the same monomers. A mixture of sodium dodecyl sulfate (SDS) and poly(ethylene oxide) dodecyl ether (Brij‐35®) were used as surfactants. The effects of monomer addition rate (R_a) and surfactants concentrations (4 or 1 wt % with respect to the initial mixture of reaction) on polymer and latex properties were studied. High copolymer content latexes (24–36 wt %) with average particle diameters (D_p) from 38 to 55 nm and relatively narrow particle size distributions, high polymerization rates, weight ratios of polymer to surfactant (P/S) from 13.3 to 32.8 were obtained. The number‐average molecular weights (M_n) were between 96,000 and 188,000 g/mol. Homogeneous copolymer compositions were obtained throughout the reaction for both, seeded and unseeded processes, which is not possible by the usual batch microemulsion process. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and properties of poly(urethane acrylate) (PUA) and tetrapod ZnO whisker (TZnO‐W) composite films

Tetrapod zinc oxide whiskers (TZnO‐Ws) were successfully synthesized via a thermal oxidation method and confirmed using Fourier transform infrared spectroscopy, X‐ray diffraction and scanning electron microscopy. A series of poly(urethane acrylate) (PUA)/TZnO‐W composite films with various TZnO‐W contents were prepared via a UV curing method and their physical properties were investigated to understand their possible use as packaging materials. The morphological, thermal, mechanical, antibacterial and barrier properties of the PUA/TZnO‐W composite films were interpreted as a function of TZnO‐W content. The thermal stability, barrier properties and antibacterial properties of the composite films, which were strongly dependent upon their chemical and morphological structure, were enhanced as the TZnO‐W content increased. The oxygen transmission rate and water vapor transmission rate decreased from 614 to 161 cm³ m^?2 per day and 28.70 to 28.16 g m^?2 per day, respectively. However, the mechanical strength of the films decreased due to the low interfacial interaction and poor dispersion with high TZnO‐W loading. The enhanced barrier properties and good antibacterial properties of the PUA/TZnO‐W composite films indicate that these materials are potentially suitable for many packaging applications. However, further studies are needed to increase the compatibility of polymer matrix and filler. © 2012 Society of Chemical Industry     

Performance Analysis of a Disk-Type Viscous Pump with Radial Pumping Grooves

A new disk-type viscous pump, with radial pumping grooves on its stator, is described and its performance analyzed. Its flow rate and discharge pressure relationship is found to be linear. Two proposed viscous pumps of this new design having slightly different dimensions are considered and compared to the recently reported design utilizing multilobes. Analyses on these two proposed pumps show that this new design exhibits higher flow rate characteristics than the recent multilobe design for the same pump size and rotor–stator clearances.     

DEGRADATION RATE OF WATER-SOLUBLE POLYMERS BY OZONE

Water-soluble polymers were degraded by ozone, and the degradation rate defined by the change of weight average polymerization degree per unit time was obtained. The degradation rate of poly(oxyethylene) (PEG) was proportional to the 1.5 to 2.0 power of the polymerization degree, and was 20 to 60 times that of poly(acrylamide) (PAAm). The experimental results of PEG and PAAm were correlated as a function of polymerization degree, temperature, dissolved ozone concentration and OH^? ion concentration. The degradation rate of poly(sodium acrylate)(PANa) was proportional to the 2.0 power of the polymerization degree when no other electrolyte was added. However, the degradation rate of PANa decreased with the increase in NaCl concentration, and approached that of PAAm in the range of high NaCl concentrations.