涂层材料的断裂分析(英文)

和基体厚度相比,涂层很薄,因此细观力学模型可把基体作为半无限弹性体。由于涂层和基体材料的膨胀系数及弹性系数不匹配,涂层材料中残余热应力的解析解为 E_c/(1-γ_c)·(α_s-α_c)△T。用有限元法校核,该应力和解析解吻合得好。通过对涂层产生裂纹驱动力和断裂韧性的讨论,提出了抗裂涂层厚度公式。     

Measurement of the thermal diffusivity of thin films on substrate by the photoacoustic method

Measurements of the thermal diffusivity of thin films on substrate have been performed by the photoacoustic method. In order to examine the method we have built a new apparatus and proposed (1) a system calibration procedure using optically and thermally thick reference samples and (2) a data analysis procedure based on the RG (Rosencwaig and Gersho) theory. As a result of using a transparent photoacoustic cell, the systematic errors which are caused by stray light have been reduced. With this apparatus, measurements have been performed on platinum, titanium, and stainless steel (SUS304) thin foils (thickness form 50 to 100 µm) with three different liquid backing materials (water, glycerol, and ethyl alcohol). The reproducibility was within ±7% regardless of film thickness and substrate materials.     

Si衬底上横向外延GaN材料的微结构和光学性质的研究

用氢化物气相外延 (HVPE)方法在Si(III)衬底上成功横向外延生长出晶体质量较好的GaN薄膜材料。透射电子显微镜 (TEM )的研究结果表明 ,横向外延区域GaN的位错密度明显减小。由于SiO2 掩膜腐蚀角的不同 (分别为 90°和 6 6°) ,导致了横向外延GaN材料一些独特的微观形貌。微区拉曼光谱由数百条拉曼散射曲线组成 ,每一条曲线有三个振动模 ,分别对应Si振动模式 (5 2 0cm- 1) ,E2 模式 (5 6 6cm- 1)和E1(LO)模式(732cm- 1)。在垂直条纹方向 ,峰位和峰宽没有明显的变化 ,而峰强约 5 μm会发生周期性变化     

关于彩涂压型钢板构件设计中的选材问题

近年来 ,在彩涂压型钢板构件设计应用中 ,由于不重视、不了解如何合理选材 ,在实际工程的材料订货中也都不提出对材料性能的技术要求 ,致使供货材质、材性不能满足使用要求 ,存在降低彩板构件承载力或减少其使用寿命的隐患 ,应引起设计人员的注意。同时对当前如何按使用条件及材料供应条件合理地选定彩板材料的性能技术要求 ,包括基板钢材的级别及力学性能、板厚及公差控制要求、镀锌层质量与彩涂层类别以及参照的技术标准等 ,提出了一些建议 ,供设计应用参考。最后还对板的强度、厚度以及镀铝锌板的选用问题进行了讨论     

Charge transfer resistance of spray deposited and compressed counter electrodes for dye-sensitized nanoparticle solar cells on plastic substrates

Electrochemical impedance spectroscopy was used to determine the effective charge transfer resistances of porous dye-sensitized solar cell counter electrodes prepared by low-temperature spray deposition and compression of conductive carbon and platinized Sb-doped SnO₂ powders on indium tin oxide-coated plastic substrates. The charge transfer resistances were 0.5–2 and 8–13 Ω cm², respectively, when using 3-methoxypropionitrile as the electrolyte solvent. The manufacturing method used lends itself to produce mechanically stable and even-quality electrodes in an easy and fast manner.     

Growth of CeO_2, Y_2O_3 Buffer Layers for YBCO Coated Conductor

~~Growth of CeO_2, Y_2O_3 Buffer Layers for YBCO Coated Conductor     

Effects of Substrate Temperatures on the Structure and UV-shielding Properties of TiO_2-CeO_2 Films Deposited on Glass by Radio-frequency Magnetron Sputtering

1Introduction Theultravioletrays(UV)insunlight(-4%)cantransmitintoroomthroughcommonfloatglass,theUVcanmakethematerialsintheroom,eg,paper,furni ture,textilefabricandplastics,becoloredanddeterio rated.ShieldingfromUVirradiationisofinterestinmanyfields.Formu…     

对未来我国覆铜板业技术发展的战略与任务的探讨

对未来十年我国覆铜板业技术发展的战略与技术开发重点任务进行了探讨。     

C－BN衬底上金刚石的异质外延生长研究

用热灯丝ＣＶＤ方法在Ｃ－ＢＮ单晶衬底上制备出金刚石膜，并且在Ｃ－ＢＮ（１００）面上观察到金刚石的异质外延。     

InGaAsP／InP PFBH激光器

采用Ｎ－ＩｎＰ衬底研制ＩｎＧａＡｓＰ／ＩｎＰ激光器和ＤＦＢ激光器在国内已报导过多次，本文介绍用Ｐ－ＩｎＰ衬底研制ＩｎＧａＡｓＰ／ＩｎＰ平面埋层异质结构激光器和ＤＦＢ－ＰＦＢＨ激光器，同时利用晶体生长和晶向的依赖关系，改进埋区的结构，使器件最高激射温度大于１００℃。