Si(111)上生长LiNbO_3薄膜的研究

利用射频磁控溅射的方法,在Si(111)衬底上制备了LiNbO3薄膜。采用X射线衍射(XRD)和扫描电子显微镜(SEM)研究了衬底温度、退火温度和溅射气体压强对LiNbO3薄膜结晶和表面形貌的影响,并用椭圆偏振仪测量了薄膜的厚度和折射率。结果表明:衬底温度为450℃时制备的薄膜,退火前后都没有LiNbO3相生成;衬底温度为500～600℃时,LiNbO3薄膜出现(012)、(104)和(116)面衍射峰,经600℃退火后3个衍射峰的强度加强;衬底温度为600℃时,经600～900℃退火得到的LiNbO3薄膜,除出现(012)、(104)和(116)面衍射峰外,还出现(006)面衍射峰;溅射气体压强从0.8 Pa增大到2.4 Pa时,经800℃退火后得到的LiNbO3薄膜表面晶粒团簇变小,而0.8 Pa制备的薄膜经800℃退火后LiNbO3相的结晶程度较其它压强下完善;900℃退火后得到的LiNbO3薄膜折射率为2.25,与LiNbO3晶体相当。     

Corner forming of AZ61A magnesium alloy tube within warm hydroforming

The corners with small radii on cross sections are crucial for forming hydroformed components with polygonal sections.In this paper,warm hydroforming experiments of AZ61A magnesium alloy tubes were carried out to study the forming regularity of round corners by using a demonstration part with square sections.Effects of temperature on radius forming,thinning ratio distribution and microstructure were revealed and a component with relative outer corner radius of 3.0 was obtained by warm hydroforming at 240℃.The minimum thickness of the formed square section was located in the transition position between the corner and the straight wall.The thinning ratio of the round corner increased with the increase of forming temperature.Formability of the magnesium tube was improved by raising temperature under the effect of dynamic recrystallization at 240℃.     

考虑冷变形加工硬化的翻边力理论计算

在分析现有计算公式存在不足的基础上,根据翻边变形区材料的应力应变特点,考虑了冷变形加工硬化(取幂函数硬化规律)和变形区材料厚度变化(翻边为变薄)两个因素的影响,利用金属塑性成形问题求解理论中的主应力法,推导和提出了圆孔翻边力计算的一个新公式.通过用钢板(SPCC)和铜板(T1)进行了翻边工艺试验的验证,并与经验公式和现有理论公式的计算结果进行了比较,表明新公式计算结果能接近于实际,且原理上更为科学合理.     

Characteristics of shell thickness in a slab continuous casting mold

The key to reduce shell breakout in the continuous casting process is to control shell thickness in the mold.A numerical simulation on the turbulent flow and heat transfer coupled with solidification in the slab mold using the volume of fluid (VOF) model and the enthalpy-porosity scheme was conducted and the emphasis was put upon the flow effect on the shell thickness profiles in longitudinal and transverse directions.The results show that the jet acts a stronger impingement on the shell of narrow face,which causes a zero-increase of shell thickness in a certain range near the impingement point.The thinnest shell on the slab cross-section locates primarily in the center of the narrow face,and secondly near the comer of the wide face.Nozzle optimization can obviously increase the shell thickness and make it more uniform.     

跨音压气机转子多目标气动优化设计

采用基于雷诺平均N-S方程的全三维流场模拟程序和基于多目标遗传算法的数值优化程序,对跨音压气机转子NASA Rotor37进行了优化设计。对所开发的三维N-S方程求解程序进行了实验验证,完善了多目标遗传算法与响应面方法相结合的具有全局寻优能力的优化程序,以总压比和绝热效率最大为设计目标,应用该优化方法对NASA Rotor37进行考虑中弧线和厚度分布的多目标气动优化设计。结果表明:在满足流量约束的条件下,绝热效率提高了0.7%,总压比提高了0.66%,并且优化设计时间大幅减小。     

硅基底上制备纳米镍粒子

采用微波加热法在单晶硅基底上制备纳米镍粒子。考察了镍源、还原剂、表面活性剂、加热方式等实验条件对单晶硅基底上制备纳米镍粒子的影响。对硅基底上纳米镍粒子的成分、结构及表面形态进行了表征。结果表明:以水合肼为还原剂、氯化镍为镍源,微波加热3 min在硅基底上可以制备出直径为30 nm的均匀单一分布的纳米镍粒子。     

Formation mechanism of subtrenches on cone-shaped patterned sapphire substrate

In this paper, the cone-shaped patterned sapphire substrates (PSS) were etched by an inductively couple plasma with BCl 3 as the reacting gas. The influence of the operating pressure and the RF bias power on subtrenches of the cone-shaped PSS and the formation mechanism of subtrenches were investigated. The profiles of patterns were characterized by FESEM (field emission scanning electron microscope). It showed that the subtrench size varied with the operating pressure and the RF bias power. As the operatin...     

不同AlQ厚度黄光OLEDs的研究

制备了一种新型的黄光器件,其结构为：ITO/2T-NATA（15 nm）/NPB（50 nm）/ADN（20 nm）：2%DCJTB：2%TBPe/Al Q（x）/LiF（5 nm）/Al（100 nm）（x=10 nm,15 nm,20nm,25 nm,30 nm）,通过对不同Al Q厚度的黄光器件的性能如发光光谱、效率、亮度-电压曲线进行比较发现Al Q厚度为20 nm时,发光强度、效率和亮度都是最好的,而发光颜色几乎不发生改变.     

ZnO一维纳米结构在金属基底上的原位生长和表征

以Cu—Zn合金片为基底并提供Zn源,在含氧气氛中通过调控反应温度和氧偏压,采用热氧化法直接在Cu-Zn合金片上大面积可控地合成了多种形貌的ZnO一雏纳米材料薄膜（包括纳米带、纳米片、纳米梳和纳米线等）,采用多种分析方法对产物的形貌、结构进行了详细的表征,并对其相应的生长模型进行了讨论。结果表明,反应温度和氧偏压对ZnO纳米结构的生长至关重要,随着反应温度升高或氧含量的减少,气相Zn／O物种的偏压比增加,ZnO纳米结构尺寸变小。