角接接头焊缝外观检查质量标准的探讨

针对厚壁管角接接头多次出现裂缝,解剖后又没有发现足以引起裂缝的除未焊透外的其它焊接缺陷的情况,认为除应力集中外,角接接头本身的强度也是决定是否会开裂的一个重要原因,为此建立了一个数学模型,同时结合实例证明.按目前大多数人认可的角接接头焊脚的定义,根据DL/T869-2004<火力发电厂焊接技术规程>去控制焊接尺寸,会出现焊缝有效厚度不足的问题.从而根据角接接头有效厚度不应小于最小壁厚的观点,提出对此类角接接头焊缝外观质量控制的几点意见.     

CoCrPtNb／CrTi／C多层膜记录介质的制备和性能研究

采用CoCrPtNb四元合金作磁记录介质，并采用多层膜结构（CoCrPt）100-Nbx/CrTi／C／Glass制备玻璃盘基硬盘。实验结果表明：采用适宜厚度的籽晶层与合适组分的底层和磁性层的多层膜结构，即使在室温下溅射，此种薄膜磁记录介质也可得到高达260kA／m的矫顽力；在550℃高温下，经过30min真空退火后，其矫顽力有较大幅度提高，并在Nb含量为2．4％（原子分数）时达到极大值386kA／m，适用于高密度磁记录。同时，也详细分析了磁性层和底层组分、籽晶层厚度以及真空退火对磁记录介质磁性能和微结构的影响。     

不等厚板过渡削薄对接焊缝的超声波探伤

不等厚板经过渡削薄处理后的对接焊缝,由于厚度的不均匀,射线穿透时的衰减不一样,对射线检测带来很大的麻烦。常用的超声波探伤方法在定位和定级方面比较困难,本文给出利用现在先进的数字式超声波探伤仪进行准确探伤的方法。     

Experimental Investigation of Epoxy Bonded Polymethylmethacrylate Joints

This paper presents an experimental investigation into various aspects of epoxy-bonded polymethylmethacrylate (PMMA) and PMMA-to-aluminium joints. The effects of adhesive thickness, overlap area, surface roughness, and environmental exposure on the joint strength were studied. Results indicated that the joint strength was not directly proportional to the overlap area, while sanding had a positive effect on the joint strength. A negative effect was observed when adhesive thickness was increased. The fatigue behaviour of adhesively-bonded joints under dynamic loading was found to be independent of frequency, for the range of values tested; however, it was dependent on the test temperature with greater reduction in fatigue life observed in PMMA-to-aluminium joints at higher temperature. Empirical equations from which the fatigue life of joints can be predicted were obtained by regression analysis. Intermittent fatigue testing of the joints was also performed. The epoxy adhesive tested proved to be a satisfactory choice for outdoor exposure. The rate of degradation of the adhesive was slow with the adherend itself degrading at a faster rate than the adhesive or the bondline.     

PKA国家参考品的制备

本文应用 PKA 微量滴定板方法,用 WHO1984年建立的 PKA 国际标准品进行标定,制备了我国第一批 PKA 国家参考品。     

多层水平气流带式干燥机的数学模型

根据干燥传质传热学原理和干燥动力学特性，建立了水平气流带式干燥机干燥过程的数学模型。该模型可以预测干燥机合理的通风道高度、带翻转最佳时间和热风风速等。为优化多层带式干燥机的结构或设计新的水平气流带式干燥机提供了理论依据。     

Analysis of the diffusion layer thickness, equivalent circuit and conductance behaviour for reversible electron transfer processes in linear sweep voltammetry

The parametric dependence of the diffusion layer thickness upon electrode potential and scan rate has been derived for reversible electron transfer processes in linear sweep voltammetry (LSV) using a simple analytical expression for the dimensionless current function. The quantitative variation of the conductance with potential and scan rate has been illustrated and the equivalent circuit pertaining to LSV has been proposed. Several earlier results pertaining to potential step experiments, thin layer voltammetry, surface bound LSV, radial flow at micro-ring electrodes, etc. are shown to arise from the general expression for the current function obtained here, thus indicating an isomorphism among various potential perturbation techniques.     

两极控制图在注塑瓶盖壁厚控制中的应用

针对注塑瓶盖壁厚控制的特点,介绍了统计过程控制(SPC)中的均值-极差(x-R)控制图在塑料瓶盖壁厚控制中的局限性,将两极(L-s)控制图与均值-极差控制图进行了比较,阐述了两极控制图在塑料瓶盖壁厚控制中的优越性,论述了两极控制图的构造原理和控制限计算方法,提出了两极控制图在注塑瓶盖壁厚控制中的应用,并在对两极控制图分析的基础上,对注塑成型的过程能力进行分析和改善。     

Particle-Substrate Collisions, Particle Rebound and Removal

Recent progress in particle capture and rebound and its effect on the adhesion force is reviewed in this paper. Particles rebound when the incident velocity is greater than a characteristic critical velocity. Lower impaction velocity particles experience elastic and plastic deformation. Recent models for particle rebound and capture are discussed and evaluated in terms of their restrictive assumptions and results. Recent experimental data of particle rebound and capture is also discussed, as is the hydrodynamic removal of captured particles. The removal of particles occurs when the applied hydrodynamic removal force overcomes the adhesion force. The effect of adhesion-induced deformation on the removal of particles is introduced and discussed.     

Shear-induced interactions in blends of HMMPE containing a small amount of thermotropic copolyester HBA/HQ/SA

Shear-induced interactions between high molecular mass polyethylene (HMMPE) melt and a thermotropic liquid crystalline copolyester, HBA/HQ/SA (TLCP) were investigated using large amplitude oscillatory shear and capillary shear. Polarized optical microscopy (POM) observations show that the mono-domain nematic TLCP droplets embedded inside a HMMPE melt may be readily elongated using large amplitude oscillatory shear. The HMMPE melt adjacent to the elongated TLCP filament was observed to crystallize faster than that in the matrix away from the interface. TEM analysis on the 1 wt% TLCP/HMMPE blend quenched after capillary shear shows that there are strong interfacial interactions between the elongated TLCP filament and the HMMPE matrix. Long range PE lamellae orientational order up to 2 μm away from the TLCP filament surface were observed, with all the lamellae surface normal parallel to the TLCP fiber. Additionally, a strong interfacial compatibility between the TLCP filament and the HMMPE matrix with an interfacial thickness of ∼30 nm has also been observed. The enhanced interfacial compatibility is attributed to the -CH₂- group interactions due to chain alignment in both components at their interface. These results provide a fundamental insight to other TLCP containing thermoplastics where compatibilities may be present due to segmental interactions.