Nitric oxide reduction and carbon monoxide oxidation over carbon-supported copper-chromium catalysts

Carbon supported copper-chromium catalysts are shown to be very active for both the reduction of nitric oxide with carbon monoxide and the oxidation of carbon monoxide with oxygen. Mixed copper-chromium oxide active phases have good activity in the simultaneous removal of nitric oxide and carbon monoxide from exhaust gases. The influence of several catalyst variables has been investigated. The activity per volume of catalyst increases with increasing loading, while the intrinsic activity shows a maximum around C/M=100−50. An optimum catalyst for nitric oxide reduction and carbon monoxide oxidation has a copper/chromium ratio of 2/1. The apparent activation energy for the carbon monoxide oxidation over carbon supported copper-chromium catalysts is 77 kJ/mol, suggesting that the Cu---O bond rupture is the rate-limiting process. The reduction of nitric oxide takes place at higher temperatures. Since all catalysts have a low selectivity for molecular nitrogen formation at lower temperatures, the dissociation of nitric oxide is probably rate determining, resulting in a slightly reduced catalyst system. In an excess of carbon monoxide the reaction is first-order in nitric oxide and zero-order in carbon monoxide. Moisture inhibits the reaction by reversible competitive adsorption, whereas carbon dioxide does not. Oxygen completely inhibits the reduction of nitric oxide due to the more rapid reoxidation of the catalytic sites compared to nitric oxide. Therefore, the reduction of nitric oxide takes place only when all oxygen has been converted and, hence, is shifted to higher temperatures. As a possible consequence, the production of nitrous oxide is reduced. Nitric oxide and molecular oxygen react preferentially with carbon monoxide, so, in an excess of oxidizing component, gasification of the carbon support occurs at higher temperatures after carbon monoxide has been completely consumed.     

无油润滑压缩机活塞环和支承环设计

通过对填充聚四氟乙烯材料活塞环及带卸荷槽结构支承环的研究 ,确定了活塞及活塞环结构 ,建立了带卸荷槽支承环的力学分析模型 ,并将其结果用于结构尺寸的确定。在压缩机工艺指标不变的情况下 ,用该方法设计的活塞环和支承环性能优良。     

深基坑支护结构计算的有限元方法

针对软土地基的特性，本文提出了考虑土体抗力释放与结构模型随施工过程改变的新杆系有限元法，并 编制了求解支护结构内力与变形的计算程序，通过对事例分析．计算结果与实际情况非常吻合，证明了该方法的合理 性。     

Information systems and uncertainty: a conspiracy of misplaced confidence

Abstract. Information technology is becoming an increasingly important factor in contemporary management. Information systems are being set up in business explicitly to accommodate the new opportunities of this technology, and these are having a lasting effect on managerial practice. The full implications of this technology-driven development have not been appreciated by organizations, which in absorbing technological systems, are tolerating a great drain on their resources.
The efficacy of computers is predicated on the acceptance of some very specific perspectives. A growing discontent and disappointment with their limited achievements is our reason for advocating a different point of view. We will discuss how a shift in perspective, particularly in respect to the perception of uncertainty, will affect thinking and practice in the field of management support systems. We will render our view of the application of computerized decision support systems (DSS), and especially, we will focus on the beliefs and assumptions that have shaped this technology thus far. To this end we will discuss the concept of uncertainty, by juxtaposing current thinking and practice with our understanding of the context of its application. Finally, we will place our understanding of uncertainty in a managerial context and explain the implications this would have for strategists.     

Pruning Redundant Alarm Correlation Patterns

1　ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｓｔｉｃｋｉｎｇｐｏｉｎｔｏｆａｓｓｏｃｉａｔｉｏｎｒｕｌｅａｌｇｏｒｉｔｈｍｓｄｅｐｅｎｄｓｏｎｅｆｆｅｃｔｉｖｅｌｙｆｉｎｄｉｎｇａｌｌｃｏｒｒｅｌａｔｉｏｎｐａｔｔｅｒｎｓｔｈａｔｓａｔｉｓｆｙｖａｌｕｅｒｅｑｕｉｒｅｍｅｎｔｉｎｔｈｅｍａｇｎａｎｉｍｉｔｙｏｆｄａｔａ.Ｂｕｔｔｈｅａｌｇｏｒｉｔｈｍｓａｌｓｏｂｒｉｎｇａｎｅｇａｔｉｖｅｅｆ ｆｅｃｔ:ｔｈｅｎｕｍｂｅｒｏｆａｓｓｏｃｉａｔｉｏｎｒｕｌｅｓｉｓｖｅｒｙｌａｒｇｅ.Ａｌｓｏｉｎｆｏｒｍａｔｉｏｎ…     

机动武器系统的含间隙动力学研究--下篇:系统仿真

本文把中篇建立的间隙铰模型引入多体系统动力学分析中,得到了一种处理含间隙多体系统动力学问题的一般方法.应用这种方法对机动武器的发射过程进行了原理性的仿真,验证了前面建立的碰撞模型和间隙模型,并分析了间隙对导弹运动状态的影响.导弹发射过程具有变拓扑的特点,本文方法提供了一种处理这类问题的思路.     

化工软测量技术研究进展

详细说明了软测量技术的含义以及软测量系统的组成。在此基础上，介绍了软测量技术中基于机理分析建模、应用状态观测器建模、应用统计分析建模、神经元网络、模糊技术、以及支持向量机的智能建模等软测量建模理论方法和最新研究成果，之后介绍了小波分析、推断控制算法在软测量数据处理中的应用，最后介绍了基于虚拟仪器开发平台的软测量系统实现技术。     

Immobilization and activation of vanadium(III) and titanium(III) single‐site catalysts for ethylene polymerization using MgCl2‐based supports

Significant increases in the activity of vanadium(III) amidinate catalysts for ethylene polymerization have been obtained by immobilization on a MgCl₂‐based support prepared by reaction of AlEt₃ with a MgCl₂/ethanol adduct. Catalyst immobilization and activation on this type of support prevents the rapid decay in activity observed under homogeneous polymerization conditions with unsupported catalysts. Stable polymerization activity is also observed with analogous titanium(III) complexes. Polyethylene with narrow molecular weight distribution and spherical particle morphology is obtained without reactor fouling. Copyright © 2005 Society of Chemical Industry     

A framework of virtual prototyping environment for the design and analysis of mechanical mechanism with clearance

Mechanical mechanisms with clearance abound in technological fields such as robotics, machine and steam turbine industry. The dynamic performance of these mechanisms in working condition can be achieved provided that the effects of the different on the mechanisms (such as mechanism dynamics, technological effects and thermal behaviour) are thoroughly understood. Virtual prototyping provides an integration of multi-domain dynamic simulation for the design and analysis process. In the current paper, a framework of virtual prototyping environment for the design and analysis of mechanical mechanism with clearance is presented. A case study with such a simulation strategy is studied for the optimum design and analysis of the technological parameter.     

The new structure of fibre glass reinforced plastics bolt

The develop actuality and direction of FRP (fibre glass reinforced plastics) bolt in the world are analyzed. The new type structure of FRP bolt was designed. Trial data indicate that, all kinds of capability target of this FRP bolt all achieve and exceed the country stand-ard, substitute present metal bolt, wood bolt and bamboo bolt and other side bolt, it can gain magnitude technology and economy benefit. FRP bolt mechanization product line produce ef-ficiency is high, its throughput a day are 750 base, this can meet demand of hit-small mining company.