快干涂料铸渗法获得铸件表面复合层的研究

对快干涂料法铸渗工艺进行了研究。查明了影响铸件表面复合层质量的主要工艺因素,确定了最佳工艺参数,为生产实践提供了依据。     

不同活化剂对石油焦基活性炭孔结构的影响

以石油焦为原料 ,Na OH,KOH和 Na2 CO3 为活化剂制备活性炭 ,采用氮气吸附考察了不同活化剂对活性炭的比表面积、中孔和微孔孔径分布、孔容积及平均孔径等孔结构的影响 .结果表明 :KOH活化制备的活性炭包含 1 nm的微孔和 4nm的中孔 ,总孔容 0 .648cm3 /g,比表面积大 ;Na OH制备的活性炭以 1 nm的微孔为主 ,占总孔容 ( 0 .1 65 cm3 /g)的 98% ,平均孔径 1 .83nm;Na2 CO3 制备的活性炭以 4nm的中孔为主 ,占总孔容 ( 0 .1 43cm3 /g)的 68.5 % ,平均孔径 3.42 nm,比表面积小 .3种样品的孔径都呈现出多峰分布特征 .KOH和 Na2 CO3 活化制备的活性炭的 N2 吸附脱附曲线属于 型 ,Na OH活化制备的活性炭吸附脱附曲线属于 型 .     

The Structure of the Irreversibly Bound Adhesion Promoter-Substrate Interfacial Layer of γ-Aminopropylsilanetriol on Crystalline Si, as Measured by XPS and FTIR

The irreversibly bound interfacial layer deposited by the γ-aminopropysilanetriol adhesion promoter onto a crystalline silicon substrate, which remains even after profuse washing, was found by XPS to have resulted from the fragmentation and rearrangement of the original γ-aminopropylsilanetriol molecule. A mechanism is proposed, involving the homolytic scission of the terminal N-C bond. One of the subsequent reactions is believed to involve hydrogen loss by abstraction and the formation of a terminal vinyl group, which bonds to the substrate. Support for this mechanism is found in IR spectroscopy of this layer.     

Investigations of surface degradation of high‐density polyethylene materials resulting from tracking,using physicochemical analysis

In the present work tracking phenomena were studied with high‐density polyethylene (HDPE) materials under dc voltage, with NH₄Cl and acid rain as contaminants. It was determined that the tracking time of the material depends on the conductivity and flow rate of the contaminant. Furthermore, physicochemical analysis by wide‐angle X‐ray diffraction studies, differential scanning calorimetry, and luminescence spectroscopy was carried out, whereupon it was concluded that the tracking process is a surface‐degradation process. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2843–2849, 2002; DOI 10.1002/app.10260     

Surface Areas of Nitrated Hydrotalcites

Hydrotalcites in the nitrate form were prepared using microwave irradiation in the hydrotreatment step. The surface area (BET) of nitrated hydrotalcites was evaluated. Solids were characterized by atomic absorption, X-ray diffraction and BET analysis. Thermal pretreatment temperature determined the surface area of the hydrotalcites.     

聚硅氧烷-丙烯酸酯共聚物互改性产物的表面特性

通过测定参照液体在固体表面的接触角，计算固体的表面能及固体／液体接触体系的粘附功，考查了聚硅氧烷-丙烯酸酯共聚物互改性产物的表面特性及其对粘接性能影响。     

Zinc Coated Steel/Epoxy Adhesive Systems: Investigation of the Interfacial Zone by FTIR Spectroscopy

The present study takes advantage of the ability of Fourier Transform Infrared Spectroscopy (FTIR) for the analysis of ultrathin organic films on metals. FTIR in the reflection mode (IRRAS) is used in order to study the interaction of ultrathin films of dicyandiamide (hardener of most one-pack epoxy resins) with various substrates, model ones such as gold or zinc and industrial ones such as steel and zinc-coated steels.

Pure zinc surfaces and, to a lesser extent, zinc-coated steels are shown to react with dicyandiamide after heating at 180°C, as evidenced by the frequency shift of the absorption band (at about 2200 cm^-1) characteristic for nitrile groups. As real systems consist of thick layers of a fully formulated adhesive cured onto a metallic substrate, the direct investigation of such a buried interphase is no longer possible by FTIR and by most of the known spectroscopies. Some mechanically tested specimens are then analysed, after failure, by FTIR microspectrometry. The spectra obtained, corresponding to the fracture initiation zone which is about 100 μm in diameter, advocate for the presence of an ultrathin layer of modified polymer still covering the substrate.     

HEAT TRANSFER BETWEEN ROUGH SURFACES IN CONTACT OVER A HIGHLY ELLIPTICAL CONTOUR AREA: COMPARISON OF EXPERIMENTAL AND NUMERICAL RESULTS

This paper describes experimental and numerical studies of heat transfer between surfaces in contact over a highly elliptical area in a gas or in vacuum. Measurements of the steady-state thermal resistance of a high aspect ratio contact formed between cylindrical steel surfaces with widely different radii of curvature (76 cm vs 0.95 cm) are reported for two levels of surface roughness (0.05 μm and 1.0 μm rms) and compared to 3-D numerical results obtained with the multigrid method. Theoretical results obtained by evaluating the contact conductance acting over each surface element within the contour area with a method developed previously for rough but nominally flat surfaces are shown to be in excellent agreement with the rough surface experimental data.     

Preadhesion Laser Treatment of Aluminum Surfaces

An excimer laser may be used for preadhesion treatment of aluminum alloys. This method presents an alternative to the use of ecologically unfriendly chemicals involved in conventional anodizing pretreatments.

Experimental results indicate that preadhesion laser surface treatment significantly improved the shear strength of modified-epoxy bonded aluminum specimens compared with untreated and anodized substrates. The best results were obtained with laser energy of about 0.2 J/Pulse/cm² where single lap shear strength was improved by 600-700% compared with that of untreated Al alloy, and by 40% compared with chromic acid anodizing pretreatment.

The mode of failure changed from adhesive to cohesive as the number of laser pulses increased during treatment. The latter phenomenon has been correlated with morphology changes as revealed by electron microscopy, and chemical modification as indicated by Auger and infrared spectroscopy.

It can be concluded that the excimer laser has potential as a precise, clean and simple preadhesion treatment of Al alloys.     

采用表面粘涂技术提高设备的抗腐蚀性能

通过表面粘涂，对受到腐蚀、冲蚀、气蚀的设备进行表面修补与防护，可提高设备的使用寿命。