Two kinds of bio-based polyurethane coatings for controlled-release urea were prepared by in-situ polymerization used castor oil and liquefied starch as raw materials, respectively. Scanning electron microscopy (SEM) showed that the section morphology of castor oil based polyurethane (Castor-PU) coating was uniform and dense, and that of liquefied starch based polyurethane (Starch-PU) coating had certain proportion of microporous. Infrared spectroscopy (IR) showed that the two coatings had typical urethane characteristic structure, but the difference was that the Starch-PU had obvious unreacted isocyanate structure. Differential scanning calorimetry (DSC) showed that the glass transition temperature of the two coatings was around 58°C, but the Castor-PU had a crystallization domain with obvious crystallization melting peak at 130°C. Thermogravimetric analysis (TG) showed that the thermal stability of Castor-PU was significantly higher than that of Starch-PU. The controlled-release property test showed that when the coating ratio was 2.8%, the nutrient release longevity of urea coated with Castor-PU was 49 days and that of urea coated with Starch-PU was 14 days. The reasons for the poor controlled-release performance of Starch-PU were analyzed, which probably caused by concentrated sulfuric acid and hydrophilic dispersant added in the liquefied starch. 相似文献
Owing to its high degree of crystallinity and orientation, the surface of aramid fiber is smooth, causing its low bonding strength with polymer matrix. This has restricted the application of aramid fiber in reinforced polymer materials. Effective methods are by introducing functional groups through surface modification and by increasing its surface roughness thereby greatly improving its bonding strength with the polymer. In this work, molecular dynamics (MD) simulation study fiber functionalized with hydroxyl (OH), carboxyl (COOH), and the silane coupling agent as nanofillers for polymer nanocomposites. The interfacial characteristics and the mechanical behavior of polymer nanocomposites are investigated. The results show that the functionalization can enhance the interfacial shear stress and tensile strength. The functional group not only provides a stronger interface, but also provides additional mechanical interlocking effect, which effectively improves load-bearing transmission capacity. The analysis of the micro-mechanism from the energy level also provides new insights for the functionalized design of nanocomposites. 相似文献
The modification of the surface characteristics after treatment with plasma in polymeric materials, such as the aging phenomenon, calls the attention of research in the area of nonthermal plasma technology. In this work, a direct treatment with dielectric-barrier discharge plasma was used on the surfaces of ultrafiltration membranes. The measurements of the contact angle with water, attenuated total reflectance accessory, zeta potential, atomic force microscopy and scanning electron microscopy-MEV were performed on the surfaces to verify changes after plasma treatment and to understand the occurrence and timing of the plasma aging effect. In the analysis of the membrane performance, hydraulic permeation and protein retention tests were performed. The results showed an improvement in wettability and hydrophilic properties in the post-treated membranes. The study of reversibility/aging of the post-plasma surface is important for research that deals with the modification of polymeric membranes. Changes in surface morphology, topography and wettability of the membranes were observed up to seven days after treatment, with a tendency to return to the initial characteristics of the membranes. 相似文献
In this work, Bis-(3-triethoxysilylpropyl) tetrasulphane was employed for surface modification of silica, ferrite and kenaf fiber filled natural rubber composites using aqueous solvent deposition, dry blending and integral blend methods. The efficiency of each method and the preferred modification method for improving the mechanical performance of natural rubber composites was assessed. The appearance of the Fourier transform infrared spectroscopy peak around 1088 cm−1 for all types of fillers provided evidence that silane interaction had occurred between the fillers and rubber and the formation of siloxane linkages were quantitatively determined by the crosslink density measurement. The surface treatment by dry method for silica and ferrite fillers showed significant improvement of tensile performance at approximately 67% and 34% compared to those with untreated fillers. For kenaf fiber-filled rubber composites, the surface treatment by aqueous solvent deposition showed the highest tensile improvement of 59% compared to the dry blending and integral blend method. 相似文献
In order to improve the interfacial adhesion between aramid fiber (AF) and rubber matrix, a simple and facile method of aramid nanofiber (ANF) coating is demonstrated in this article. Tannic acid (TA) and polyethyleneimine (PEI) are polymerized in an alkaline solution to form a thin TA/PEI (TP) layer that is deposited on the surface of AF to introduce functional groups such as hydroxyl and amino groups. Then, the ANF coating is utilized to construct nanostructures on the surface of AF to improve the interfacial adhesion between the fiber and the rubber. Through hydrogen bonding and/or π-π stacking between the TP layer and the ANF, the ANF coating is firmly attached to the surface of AF. Compared with the untreated fiber, the interfacial adhesion of AF coated with ANF after 1, 3, 5, 7, 9 deposition cycles is increased by 27.8%, 29.1%, 31.5%, 43.1%, and 30.3%, and the mechanical properties of the fibers remain almost unchanged. This method shows its advantages of simple, facile, and time-effective, which is of great significance for industrial applications. 相似文献
A simple approach was developed to fabricate high-performance MXene/cellulose (MC)-based electromagnetic interference (EMI) shielding papers. The oriented MXene sheets located on one side of cellulose filter paper construct a continuous conductive layer, endowing the MC paper with high electrical conductivity (240.1 S/m) and excellent EMI shielding effectiveness (29.3 dB for 0.192-mm thickness) at an MXene content of 0.72 vol%. Moreover, the EMI shielding effectiveness of four stacked MC papers reached 40.5 dB. This result means that 99.9911% of the microwave radiation is attenuated, and 0.0089% is transmitted, through the four-piece MXene/cellulose filter papers. Therefore, MC paper has promising properties for excellent EMI shielding materials in current electronic devices. 相似文献
In this paper, the use of the ball burnishing process to improve the final quality of form tools (moulds and dies) is studied. This process changes the roughness of the previously ball-end milled surfaces, achieving the finishing requirements for plastic injection moulds and stamping dies. Ball burnishing can be easily applied in the same machining centres as those used for milling. In this way, both lead times and production costs can be dramatically reduced.
Both the burnishing system and its main parameters are taken into account, considering their influence on finishing. Workpiece surface integrity is ensured due to the surface smoothing effect of process and the associated cold working. Examples of different materials, machined surfaces, and industrial applications are explained, with respect to the maximum and mean surface roughness achieved.
The main conclusion is that using a large radial depth of cut in the previous ball-end milling operation, together with a small radial depth during burnishing can produce acceptable final roughness. Savings of production times are high, as burnishing is applied using the maximum linear feed of the machine, while milling must be made at moderate feeds. Moreover, ball burnishing NC programming is less critical and needs less care in its definition than CAM for milling. 相似文献