Reticulated Porous Multiphase Ceramics with Improved Compressive Strength and Fracture Toughness

A multiphase reticulated porous ceramic (RPC) as Si₃N₄–Al₂O₃–SiO₂ was fabricated by replication techniques. Proper volumes of additives and twice sinter- twice immerse process endow the RPC an excellent crack healing and submerging property. The compressive strength and fracture toughness improved owing to the crack bridging behavior. The existence of pores in struts in RPC blunt the crack tip and increased the external force needed to propagate the crack. The mechanisms play a beneficial role in enhancing the compressive strength and fracture strength. Si₃N₄ RPC with additives of 5%Al and 5% Al₂O₃ yielded the compressive strength of 9.8 MPa and fracture toughness of 0.3 MPa m^1/2.     

高强铝合金断裂韧性的研究现状及展望

通过对三种裂纹模式的概述，引出了铝合金断裂韧性的概念及断裂判据，重点评述了影响高强铝合金断裂韧性的内在与外在因素，以及断裂韧性与其它力学性能间的关系，最后提出了几个在今后的研究及应用中需要重点解决的问题。     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

利用测井资料预测塔河油田地层破裂压力

针对塔河油田奥陶系碳酸盐岩油藏 ,介绍了地层破裂压力预测和地层裂缝高度预测的基本原理 ,选择了塔河油田 4口井的资料进行了破裂压力和裂缝高度预测的成果处理。为塔河油田奥陶系碳酸盐岩储层改造提供了较为可靠的施工参数     

拉伸试验测量不确定度的研究

分析了拉伸试验中抗拉强度Rm的影响因素，对测量不确定度的主要分量进行量化，评定了Rm的相对测量不确定度，作为生产检验中评定测量不确定度的尝试，以便为用户提供钢材性能测量结果的不确定度。     

钢带试样位向及拉伸性能的探讨

从碳素结构钢热轧钢带各向异性的事实出发 ,阐述不同试样位向导致同一钢带不同的拉伸性能 ,因而影响钢带合格与否的判定。在全面考虑钢带和焊管标准的基础上 ,提出解决钢带判定的两种方法。同时 ,还对标准中存在的缺点作了说明 ,提出改进意见 ,供标准修订时参考。     

非均匀裂缝性油藏压力动态

在介绍具有连续基质颗粒大小分布和孔间表皮裂缝性油藏的不稳定压力分析模型的同时。提出了代表实际变化的裂缝密度和均匀性油藏的基质岩块大小分布概率密度函数，给出Laplace空间井筒压力解。该理论通过裂缝跨度变化拓宽了以前的双孔隙油藏模型，在不考虑孔间表皮的情况下，对非均匀裂缝性油藏压力动态进行了分析。     

Prediction of the energy dissipation rate in ductile crack propagation

In this paper, energy dissipation rate D vs. Δa curves in ductile fracture are predicted using a ‘conversion’ between loads, load‐point displacements and crack lengths predicted by NLEFM and those found in real ELPL propagation. The NLEFM/ELPL link was recently discovered for the DCB testpiece, and we believe it applies to other cracked geometries. The predictions for D agree with experimental results. The model permits a crack tip toughness R(Δa) which rises from J_c and saturates out when (if) steady state propagation is reached after a transient stage in which all tunnelling, crack tip necking and shear lip formation is established. J_R is always greater than the crack tip R(Δa) and continues to rise even after R(Δa) levels off. The analysis is capable of predicting the usual D vs. Δa curves in the literature which have high initial values and fall monotonically to a plateau at large Δa. It also predicts that D curves for CCT testpieces should be higher than those for SENB/CT, as found in practice. The possibility that D curves at some intermediate Δa may dip to a minimum below the levelled‐off value at large Δa is predicted and confirmed by experiment. Recently reported D curves that have smaller initial D than the D‐values after extensive propagation can also be predicted. The testpiece geometry and crack tip R(Δa) conditions required to produce these different‐shaped D vs. Δa curves are established and confirmed by comparison with experiment. The energy dissipation rate D vs. Δa is not a transferable property as it depends on geometry. The material characteristic R(Δa) may be the ‘transferable property’ for scaling problems in ELPL fracture. How it can be deduced from D vs. Δa curves (and by implication, J_R vs. Δa curves) is established.     

离心式高炉鼓风机扩压叶片断裂事故分析及处理

通过高炉鼓风机扩压叶片断裂事故，从化学分析、物理检验，结合使用情况对扩压叶片断裂原因进行了详细分析，并提出了改进措施。